SeeEyes SC-IPC07PU User manual
Release Version 1.1
1 Channel IP Over UTP Transmission Solution
SC-IPC07PU
User Manual
1-channel Transmitter
1-channel Receiver
Release Version 1.1
1
Precaution and Safety Guidelines
The content of this guideline is intended to protect user safety and prevent property damage.
Please read these operating instructions carefully and use the device properly.
Warning (If you do not keep any of the below guidelines, you may get
seriously injured or cause somebody’s death.)
■Be sure to install the product after unplugging power cord. Also, do not use many power
plugs at the same time.
- It may cause abnormal heat, fire and electric shock.
■Do not leave the device in a place where water will fall or splash. Also, do not place anything
with water on it, such as a vase of flowers.
- A malfunction or fire may result if liquid gets inside the device
■Do not bend the power cord by excessive force. Make sure the power cord is not crushed by
heavy things.
- It may cause fire.
■Do not open the lid arbitrarily as this device has high voltage part inside. Never disassemble,
repair or modify it.
- Abnormal work could result in fire, electric shock, and injury.
■Do not install this product in places with high humidity, dust, or soot.
- It may cause electric shock and fire.
■Do not tug at the power cord section or unplug the power plug with wet hands. If the power
cord is loose, do not plug in.
- There may be a risk of fire and electric shock.
■Always keep the location clean and dust-free during or after installing the device. When
cleaning the device, be sure to wipe it with a dry towel and do not use water, thinner, or organic
solvents.
- It may cause malfunction or fire
■Keep the device in a cool place where doesn’t let direct sunlight. Keep it at a proper
temperature and avoid heating appliances like candle or heater. Also, keep the equipment or
tools away from places where people come and go.
- There is a risk of damage to the surface of the device and a risk of failure, electric shock or fire.
■Pay attention to possible hazards in the workplace, such as wet floor, ungrounded power
extension cables, old power cords and a lack of safety earth. Consult your place of purchase or
professional if problems arise.
- It may cause fire and electric shock.
■Concerning the input voltage for operating this device, a voltage range must be within 10%
of rated voltage. Also, do not use a heat source such as a hair dryer, iron and refrigerator to the
same power unit.
- It may cause abnormal heat, fire and electric shock.
■When thunder or lightning strikes, please pay attention to the safety and unplug the power
cord.
Release Version 1.1
2
Caution (Failure to follow any of the following guidelines could result in
personal injury or property damage.)
■Avoid installing near strong magnetic fields or radio waves and wireless devices such as
radio or TV.
- Install in a place that is free from magnetic, radio, or excessive vibration.
■Proper ambient temperature and humidity are recommended.
- Avoid extremely high temperatures (above 50°C) or low (below -10°C), and humid conditions.
■Be sure to plug the power cord with grounded outlet.
- There is a risk of electrical shock and personal injury.
■When this device is used near devices that generate strong radio waves, such as Radio
devices (TRANCEIVER, walkie-talkie, etc.), repeaters, etc. this can affect the video signal and
abnormalities such as noise or cracks appear on the device. Do not use it, as this may cause the
device to malfunction.
■Disconnect the power plug with care during thunder and lightning.
■When connecting cables, install as “U” shape in order to prevent rainwater/dew/fog from
getting into the product.
■Refer to the user manual for problems or questions besides the above. Contact our service
center if you need assistance from a professional technician.
■UTP(Unshielded Twisted Pair) Cable is for indoor use only. Use a STP(Shield Twisted Pair)
Cable which is shielded for outdoor use.
- Use standard CAT.5e or higher UTP cable.
■Make sure to separate general communication network (internet / in-house use, etc.) from
CCTV network.
- It may cause malfunction.
■Transmission distance may vary depending on the type of UTP cable.
■Refer to this user guide for any issues and enquiries. If you need professional assistance,
please contact the place of purchase or our service center.
■Be careful not to change the network cable configuration.
- Refer to the cable wiring way below.
Network Cable Diagram
TIA / EIA 568B Type
Pin No.
Color
Function
1
White
Orange
TX+
2
Orange
TX-
3
White
Green
RX+
4
Blue
PWR+
5
White
Blue
PWR+
6
Green
RX-
7
White
Brown
PWR-
8
Brown
PWR-
Release Version 1.1
3
1. Introduction
1-1. Overview
SC-IPC07PU, consisting of a 1-channel transmitter and a 1-channel receiver, transmits Ethernet data
and power via a UTP cable. Its built-in power supply function (IEEE802.3at) operates the transmitter
and the PoE camera from the receiver side without separate power lines. It compensates for the
conventional short-range network system by transmitting Ethernet data over long distances. SeeEyes
EoU solution is highly cost effective by minimizing construction time and costs, as you can replace
your old UTP system with a network by keeping your UTP cable (CAT.5e).
1-2. Features
•Transmission of Ethernet data maximum 800m/10Mbps or 500m/100Mbps via UTP cable(CAT.5e)
•Power supply for the PoE IP camera (PoE type B / max. 30W)
•Transmission bandwidth: maximum PHY rate (Physical Layer Speed): 100 Mbps
•Auto MDI / MDIX function
•Auto-diagnostic function for stable power supply
•PoE ON / OFF switch mounted on the transmitter
•Built-in surge protection circuit
2. Components
2-1. Transmitter
Transmitter
Mounting bracket
RJ-45 Cable
Manual
2-2. Receiver
Receiver
DC 48V(56V)
Adapter
(Option)
Power Cord
Mounting
Bracket
Manual
Release Version 1.1
4
3. Product Parts and Functions
3-1. Transmitter
①CAMERA PoE: A Switch for setting the power supply of the PoE IP camera.
※When the product is turned on, each LED will first light up in sequence and the product will
operate.
※The factory setting for the PoE switch is ON.
※When connecting a non-PoE IP camera, set the CAMERA PoE switch to OFF.
②LED Indicator
Name
Color
Status
PWR
Red
On: Successful power input
Off: No power input
ETH
Green
Flashing: Successful Ethernet connection
Off: No Ethernet connection
LINK
Green
On: Successful connection to the receiver
Off: Not connected to the receiver
PoE
Red
On: Successful PoE supply to the IP camera
Off: No PoE input to the IP camera
Flashing: IP camera overcurrent (short / open circuit)
※When the product is turned on, each LED will first light up in sequence and the product will
operate.
③RECEIVER SIDE: Port for connecting the receiver and outputting video
④CAMERA SIDE: Port for connecting the IP camera
④
③
①
②
Release Version 1.1
5
3-2. Receiver
①NVR SIDE: A connection port to the NVR or PoE hub.
②TRANSMITTER SIDE: A connection port to the transmitter and for the video input.
③DC 48~56V IN: A connector for connecting the DC power adapter (48V or 56V).
※The PoE output and its transmission distance may vary depending on the adapter.
④LED Indicator
Name
Color
Status
PWR
Red
On: Successful power input
Off: No power input
ETH
Green
Flashing: Successful Ethernet connection
Off: Ethernet Not connected
LINK
Green
On: Successful connection to the Transmitter
Off: Not connected to Transmitter
PoE
Red
On: Successful PoC output to the Transmitter
Flashing: Transmitter or cable overcurrent (short / open circuit)
⑤Bandwidth Selector Switch: Supports 100Mbit/s or 10Mbit/s setting
※10M: Transmission at 10Mbps (10Mbps over CAT.5e: 800m).
※100M: Transmission at 100Mbit/s (100Mbit/s via CAT.5e: 500m).
※When the product is turned on, each LED will first light up in sequence and the product will
operate.
⑤
①
②
③
④
Release Version 1.1
6
4. Application Diagram
4-1. When connecting a PoE IP Camera (Tx’s PoE Switch must be ON)
<Installation Guide>
①Set the CAMERA PoE switch on the transmitter to ON. (PoE LED on)
※If you are connecting a non-PoE camera, set the CAMERA PoE switch on the transmitter to OFF.
②After you have connected an IP CAMERA to the transmitter, connect the transmitter and the receiver
using a UTP cable.
③Connect UTP cable connected to Transmitter to Receiver. Connect Receiver to NVR or PoE Hub.
④Check the transmission distance and set the Bandwidth switch of the receiver to the corresponding
transmission speed.
※10M: Transmit by 10Mbps (10Mbps over CAT.5e : 800m).
※100M: Transmit by 100Mbps (100Mbps over CAT.5e : 500m).
⑤Supply power by connecting DC Adapter (48V or 56V) to the DC Jack of the receiver.
⑥Check the camera's video on the monitor connected to the NVR.
※If it is connected correctly, the LINK LED on Tx and Rx lights up and the ETH LED flashes.
CAMERA PoE switch OFF
Transmitter as OFF
Transmission Distance over UTP cable (CAT.5e):
10Mbps-800m & 100Mbps-500m
Tx
Rx
Release Version 1.1
7
5. Specifications
MODEL
Transmitter
Power Input
PoE (PoE input from the receiver)
Power Output
Midspan PoE (Type B Only, PoE SW On/Off available)
Transmission Bandwidth
100Mbps
Connection Port
RECEIVER SIDE
RJ-45 (TIA/EIA568B Type)
CAMERA SIDE
RJ-45 (TIA/EIA568B Type)
LED Indicator
PWR
RED LED
ETH
GREEN LED
LINK
GREEN LED
PoE
RED LED
CAMERA PoE SW
Slide Switch
Operating Temperature / Humidity
-10℃~ 50℃/ 0 ~ 80%
Case Body / Weight
ABS / 52g
Dimensions
76(W) x 55(H) x 24(D)
MODEL
Receiver
Power Input
DC 48V-56V/1A adapter or PoE HUB (IEEE 802.3at)
Power Output
PoE (DC 48V)
Power Consumption
DC 48V~56V/900mA
Max. Transmission Distance
100Mbps: 500m (CAT.5e)
10Mbps: 800m (CAT.5e)
Transmission Bandwidth
100Mbps
Connection
Port
TRANSMITTER SIDE
RJ-45 (TIA/EIA568B Type)
NVR SIDE
RJ-45 (TIA/EIA568B Type)
DC 48V-56V IN
DC-JACK
LED
Indicator
PWR
RED LED
ETH
GREEN LED
LINK
GREEN LED
PoE
RED LED
Bandwidth Select Switch
10M: 10Mbps, 100M: 100Mbps
Operating Temperature / Humidity
-10℃~ 50℃/ 0 ~ 80%
Case Body / Weight
ABS / 54g
Dimensions
76(W) x 55(H) x 24(D)
Release Version 1.1
8
6. Power Output (Calculated Value)
Cable Transmission
Distance (CAT.5e)
Transmission
Bandwidth
With
DC48V 1A Adapter
With
DC56V 1.16A Adapter
Cable Loop
Resistance
100m
100Mbps
30W
30W
18.2Ω
200m
100Mbps
17.2W
30W
36.2Ω
300m
100Mbps
11.4W
22W
54.7Ω
400m
100Mbps
8.6W
16.6W
72.9Ω
500m
100Mbps
6.86W
13.3W
90.8Ω
600m
10Mbps
5.8W
11.2W
111.1Ω
700m
10Mbps
4.9W
9.6W
128.7Ω
800m
10Mbps
4.2W
8.3W
147.4Ω
※The transmission distance may vary depending on the specification of camera and NVR.
※In case of using PoE function of the Transmitter, the transmission distance may vary depending on
the type of camera.
Especially, use exclusive adapter for cameras with high power consumption such as IP PTZ
cameras and the cameras with many IR LEDs.
※When transmitting cable distance of 500m or more, the camera input voltage may low.
Therefore, use DC56V adapter connected to the receiver.
7. Installation Precautions
※Use exclusive power adapter separately for each product. It is not recommended to use single
adapter for supplying power to several products.
※It is not recommended to place products in close or tie each other.
※It is not recommended to connect adapter to DC jack when supplying power to the Receiver by
PoE.
※When installing the product by supplying power by PoE, it is recommended to check the video
first and ground the camera.
※When using a surge protector, the cable distance between camera and Receiver is recommended
to be within 50M.
※Use of LAN cable extension gender (coupler) may cause signal attenuation. It is not recommended
to use multiple extended gender connections.
Release Version 1.1
9
8. Troubleshooting
Symptom
Identification method
No Power.
<Transmitter>
•Check if the receiver's PoE LED is on and the transmitter's PWR LED
is on.
•Check the UTP cable connection.
<Receiver>
•Check the AC power cable.
•Check that the power switch is ON.
•Check if the PoE LED is operating normally.
No Video.
•Check whether the LINK LED on the product lights up and the ETH
LED flashes.
•Check whether the transmission distance exceeds the recommended
transmission distance.
•Check that the NETWORK CABLE is arranged correctly.
•If you are using the PoE function of the transmitter, check that the
PoE LED is lit. If it's turned off, set the PoE switch to ON..
No PoE supply
•Check the transmitter's PoE switch.
•Check that the PoE LED on the transmitter is RED.
•Check that the NETWORK CABLE is arranged correctly.
•Make sure that your IP CAMERA is PoE capable.
The NETWORK
connection is
abnormal.
•Check that the NETWORK CABLE is arranged correctly.
•Check the area for radio devices or devices that generate strong
radio waves.
•Check whether the network configuration is designed correctly.
The video status is
not stable
•Check the NETWORK cable connection.
•Check the mutual compatibility between the NVR and the camera.
•Check the camera's performance status.
Release Version 1.1
10
9. Warranty Certificate
This product has passed thorough quality control and test, and if this gets broken during
normal use, we provide the two-year warranty service.
Model No.
Serial No.
Distributor
Date you purchased
Place you purchased
Warranty Period
Two (2) year from the date of purchase
Purchaser
Name
Address
•Please check this warranty indication first.
•Please contact your distributor after checking out any defect in the products.
•The standard for repairing, replacement or reimbursement follows Customer.
•Warranty content any defect under normal use within the warranty service period we
give you free repair service according to the warranty certificate.
•We charge you with the fee of parts and service despite of free warranty service period.
Any breakage made without care such as:
- Breakdown due to natural disasters (lightning, fire, flood, tsunami, etc.)
- When disassembled or repaired by the user
- When connecting power other than rated power.
- When you want to reassemble for full system or replace parts within warranty
service period.
- When unauthorized person modified or made damage on the product trying
to repair it.
- Failure due to careless handling of the user
- When replacing consumables
- Lightning strike.
•Please note that we don’t support the breakage after warranty service period expired. If
the customer wants to get it repaired, we charge them with the fee.
•The specification is subject to change without prior notice for quality improvement.
Other manuals for SC-IPC07PU
1
Table of contents
Other SeeEyes Receiver manuals
