Sega Sonic QuadAir User manual

1
Version 9.26.12
Sonic QuadAir
Air Hockey Table Owners Manual
Assembly operation and care instuctions.
Serial #
Distributed By
Sales Person
Technical Service #
QUADAIR PATENTED WORLDWIDE

1
Forward
First, we would like to thank you very much for
purchasing the QuadAir from Barron Games
International. [This product is a multi-player game for
an entertainment centerpiece.]
For your own safety, please read through this
instruction manual that we have prepared for you
thoroughly, and take precautions when using the
product. We hope that you will become accustomed to
the product quickly.
Note before assembling
1. Inspect to make sure all of the parts are included
and not damaged.
2. Prior to assembly, you must ensure there is
sufficient space for placing or shifting this product.
3. QuadAir needs at least 6 people for assembly and
ensure your safety and the safety of others around
you when moving the product.
Tools required for assembling
• QuadAir Manual
• Screw Driver or Drill
• Scissors
• QuadAir Door Key [located inside the table]
*Note: Prepare the above specified tools. Be careful not to damage
the product while using these tools

Assembly Procedures
The wooden side
is the bottom surface
of the QuadAir.
32
1. Use scissors or a knife to cut* through the packing tape.
*Do not cut too deep or you will damage the unit.
2. Open the cardboard box to ensure the wooden side is
facing up and the playfield is facing down to the floor.

For Legs
16 Roundhead screws M8x25
16 Flat washers M8x16
For machine
3 serial number 2868
QuadAir keys
32
Use a screw driver or drill to unscrew the 4 screws on
the panel with the sticker “PARTS” on it. Once the panel
is opened, please take out the parts indicated below.

Power cord holder.
After taking out the keys, open the center door panel, and
take out all other parts from inside of the machine’s body.
+
+
+
20 Pucks 2 Red Mallets 2 Blue Mallets
1 Polish Spray Wax 1 AC power cord
4
4 QuadAir Plastic Legs
4 Adjustable Leg Levelers 2 Accessory boxes
(Accessories inside the
box are illustrated below)
(Do not remove
air blower)

Attach power
cord to
cord holder.
(1) roundhead screw M8x25
(1) flat washer M8x16
Attach the leg levelers
to the base of legs.
Grey surface
Finished picture
Tightly attach.
1
5
Take out the 4 QuadAir plastic legs and screw the adjustable
leg levelers onto the base of the legs. Place the legs on the
bottom surface of the table. Ensure alignment and then
attach with the big flathead screw M5x35 and washer M8x16.
*Make sure grey surface is facing out.
Ensure all legs are tightly attached
then flip the table 90 degrees.
This action requires at least 6
people. Flip it another 90 degrees
to place the legs on the ground.
*Place the included foam padding
on either side of the goal release
bay. Do not damage the goal
bay or LED lights.
Foam
Padding

Warning labels are attached by the goal of each side.
1
6 7
Safety Instructions for use and play.
ATTENTION
ATTENTION
Do not hit the puck with the mallet when the
puck is not leveled and flat.
Spectators don’t stand by the side of table.
This may cause cause injury.
Hold the mallet by the handle and not
the base or puck may hit fingers.
This game features
flashing lights which
may not be suitable for
photosensitive epilepsy
How to Play Quadair
1. Need 2 Players to Start. Insert coins.
2. Defend your Goal!
3. You have 5 lives until Game Over.
4. Insert coin to continue game.
Risk of Electric Shock
Playing Warnings
Hazardous voltage which can cause electrical shock
exists inside the equipment. Only qualified personnel
should work inside the equipment.
Do not hit the puck with the mallet when the puck is
not level and flat.
Spectators should not stand by the side of the table.
This may cause injury.
Hold the mallet by the handle and not the base or the
puck may hit fingers.
This game features flashing lights which may not be
suitable for photosensitive epilepsy.

32
6 7
How to Play QuadAir 1. Need 2 Players to Start. Insert credits. 2. Defend your Goal! You have 5 lives. 3.
After 5 lives Game Over. Time is limited.
4. Insert coin to continue game.
Do not hit the puck with the mallet when the
puck is not level and flat.
ATTENTION
BEWARE OF
ELECTRIC SHOCK

3
9
2
8
ATTENTION
This game features
flashing lights which
may not be suitable for
photosensitive epilepsy
Spectators should not stand by the side of
table. This may cause cause injury.
Hold the mallet by the handle and not
the base or puck may hit fingers.

First, ensure the power is off. Open the door with a key.
Hold the panel's handle and pull it out until half of the
power panel is exposed.
Handle on
the panel
Open the door with a key
Note: Do not touch open terminals or exposed wires while
the game is on. Risk of electric shock.
Descriptions of internal hardware
Power supply
Motherboard
Sound board
Coin Counter
9
8
4
Manual for the software of the machine
BEWARE OF
ELECTRIC SHOCK