SEI CM234800TX User manual

Page | 1
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]m
www.seidal.com
CM234800TX
Harvey Mixed Tone Credenza
Assembly Instructions
PO#:

Page | 2
Harvey Mixed Tone Credenza
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures.
Using the incorrect hardware will cause damage.
A.
Quantity
of 1
Top Panel
B.
Quantity
of 1
Bottom Panel
C.
Quantity
of 1
Left Side Panel
D.
Quantity
of 1
Right Side Panel
E.
Quantity
of 1
Left Vertical Panel
F.
Quantity
of 1
Right Vertical Panel
G.
Quantity
of 3
Adjustable Panel
H.
Quan
tity
of 1
Left Door
I.
Quantity
of 1
Middle Door
J.
Quantity
of 1
Right Door
K.
Quantity
of 1
Back Panel
L.
Quantity
of 2
Metal Frame

Page | 3
M.
Quantity
of 4
Metal Rail
1.
Quantity
of 12
Cam Bolt
2.
Quantity
of 12
Cam Lock
3.
Quantity
of 16
Wood Dowel Dia 8 x 30mm
4.
Quantity
of 3
Magnet
5.
Quantity
of 16
Flat Head Screw
Dia 1/8” x 5/8”L
(For Magnet and Bracket)
6.
Quantity
of 3
Magnet Plate
7.
Quantity
of 12
Shelf Pin
8.
Quantity
of 6
Hinge
9.
Quantity
of 36
Screw Dia 1/8” x 5/8”L
(For Hinge )
10.
Quantity
of 4
Leg’s Leveler
11.
Quantity
of 4
Round Head Bolt
12.
Quantity
of 4
T
-
Nut

Page | 4
13.
Quantity
of 32
Round Head Screw
Dia1/8”x1/2”L (For Back Panel)
14.
Quantity
of 20
Flat Washer
15.
Quantity
of 20
Spring Washer
16.
Quantity
of 16
Short Bolt Ø1/4” x 1/2”L
17.
Quantity
of 4
Long Bolt
Ø1/4”
x
1
-
1/2”L
18.
Quantity
of 1
Allen Wrench
19.
Quantity
of 3
Flat Head Screw
Dia 1/8” x 1/2”L
(For Magnet Plate)
20.
Quantity
of 4
Screw
Dia 1/8” x 1-1/2”L
21.
Quantity
of 4
Anchor
22.
Quantity
of 4
Bracket
23.
Quantity
of 2
Plastic Strap
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call customer service at 1-800-633-5096.
Assembly Tool Required No.2 Phillips
Screwdriver (Not Included)

Page | 5
Figure 1
Screw with fingers to help align screws
before using screwdriver.
Attach Magnets (4) to Top Panel (A)
using Flat Head Screws (5).
Tighten Flat Head Screws (5) with
Phillips screwdriver.
Figure
2
Screw with fingers to help align cam
bolts before using screwdriver.
Insert Cam Locks (2) into corresponding
holes on Side Panels (C & D) and
Vertical Panels (E & F).
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Top Panel (A).
Attach Top Panel (A) to Side Panels (C
& D) and Vertical Panels (E & F) by
inserting Wood Dowels (3) and Cam
Bolts (1) into corresponding holes until
panels meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Harvey Mixed Tone Credenza
Assembly Instructions
3

Page | 6
Figure 3
Insert Cam Locks (2) into holes on
assembled unit.
Screw Cam Bolts (1) and insert Wood
Dowels into holes on Bottom Panel (B).
Insert T-Nut (12) into predrilled holes on
Side Panels (C & D).
Attach Bottom Panel (B) to assembled
unit by inserting Wood Dowels (3) and
Cam Bolts (1) into corresponding holes
until panels meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Insert Bolts (11) though corresponding
holes on bottom of Bottom Panel (B)
and into T-nuts (12). Tighten Bolts (11)
with Phillips screwdriver.
Figure 4
Attach Back Panel (K) to backside of
assembled unit with Round Head
Screws (13).
Tighten Screws (13) with a Phillips
screwdriver.
Note: Make sure the arrow on Back
Panel (K) is pointing up.
3
F11

Page | 7
Figure 5
Attach Metal Frame (L) to Metal Rails
(M) with Short Bolts (16), Spring
Washers (15) and Flat Washers (14) as
shown.
Do not fully tighten bolts until Figure 8 is
complete.
Figure 6
Attach second Metal Frame (L) to
assembled rail with Short Bolts (16),
Spring Washers (15) and Flat Washers
(14) as shown.
L
M
M
M
M
M

Page | 8
Figure 7
Attach Leg’s Levelers (10) to rail by
hand.
Figure 8
Connect assembled rail to assembled
unit with Long Bolts (17), Spring
Washers (15) and Flat Washers (14) as
shown.
Tighten Long Bolts (17) with Allen
Wrench (18).
Check and tighten all Bolts with Allen
Wrench (18).
Stand the Credenza up.

Page | 9
Figure 9
Attach Hinges (8) to Door Panels (H), (I)
and (J) with Screws (9).
Tighten Screws (9) with Phillips
screwdriver.
Attach the Metal Plates (6) onto the
inside of the door frames using Flat
Head Screws (19).
Tighten Flat Head Screws (19) with a
Phillips screwdriver.
F igure 10
Attach Door Panels (H), (I), and (J) to
assembled unit with Screws (9) as
shown.
Tighten Screws (9) with Phillips
screwdriver.
screw for
adjusting the
door

Page | 10
Figure 11
Insert Shelf Pins (7) into corresponding
holes on Side Panels and Vertical
Panels.
Place Adjustable Shelves (G) onto Shelf
Pins as show.
Figure 12
To open doors, push on corner
corresponding to magnet.
Push door on corresponding corner to
close.
close open

Page | 11
Figure 13
Attach Brackets (22) to back panel using
Screws (5).
Tighten Screws (5) using Philips
screwdriver.
Mark two desired locations on wall and
drill two 3/16" holes.
Insert Plastic Anchors (21) into two
holes on wall as shown. Use a hammer
to insert plastic anchors until they are
flush with wall.
Then, attach Brackets (22) onto wall
using Screws (20).
Tighten Screws (20) using Philips
screwdriver.
Figure 14
Move this item close to wall Brackets
(22) and tie in all Brackets (22) together
with Plastic Straps (23) as shown in
diagram.
Anti-tipping hardware must be
used for this product to avoid
tipping and injury.
21 20

Page | 12
Figure 15
Tip: If the Credenza is not level, please
adjust the Leg’s Leveler (10) by hand as
shown.
Figure 16
Now your Harvey Mixed Tone
Credenza is ready for use.

Page | 13
Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame.Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to
provide parts or replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas)
Mon-Fri 9am – 4pm CST, or email us at [email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[email protected]om
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
Page 4