SEI MENDELL HUTCH User manual

For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-6 -5096
[e-mail]
www.seidal.com
MENDELL HUTCH
HO270200TX-ESPRESSO
Assembly Instructions
PO#11906

A Quantity
of 6
CAM BOLT（￠6.5*5mm）
B Quantity
of 0
WOOD DOWEL（￠8*0mm）
C Quantity
of 6
CAM LOCK（￠14.8*11.5mm）
D Quantity
of 14
HEXAGON SOCKET BOLT
（￠1/4”*1- /8”）
E Quantity
of 14
SPRING WASHER（￠1/4”）
F Quantity
of 14
FLAT WASHER（￠1/4”*1 mm）
G Quantity
of 1
ALLEN WRENCH（4mm）
H Quantity
of
STOPPER（L40*W16mm）
I Quantity
of 2
CONNECTION PLATE
（L45*W12*D1mm）
J Quantity
of 24
FLAT HEAD LONG SCREW
（#8*25mm）
K Quantity
of 7
FLAT HEAD SHORT SCREW
（￠ *12mm）
L Quantity
of 2
ROUND HEAD SCREW
（￠ *15mm）
M Quantity
of
KNOB（￠28.5*24mm）
N Quantity
of
BOLT（￠5/ 2”*1-1/4”）
O Quantity
of 6
COVER（￠16mm）
P Quantity
of 2
WALL AHCHOR
Q Quantity
of 2
ANTI-TIP CHAIN
R Quantity
of 4
ANTI-TIP BRACKET
MENDELL HUTCH
Parts List
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware. Do not return to store/retailer.
Using a screw that is too long will cause damage.
Before beginning assembly, separate each type of screw. Carefully study the
screw diagrams below . You may receive extra hardware with your unit.

S Quantity
of 2
SCREW（￠4*16mm）
T Quantity
of 2
SCREW（￠4*25mm）
(1) Quantity
of 1
TOP PANEL
(2) Quantity
of 1
LEFT SIDE PANEL
(3) Quantity
of 1
RIGHT SIDE PANEL
(4) Quantity
of 1
FRONT UPPER BAR
(5) Quantity
of 2
UPPER VERTICAL PANEL
(6) Quantity
of 1
LOWER VERTICAL PANEL
(7) Quantity
of 1
UPPER SHELF PANEL
(8) Quantity
of 1
LOWER SHELF PANEL
( ) Quantity
of 1
BASE
(10) Quantity
of 1
BACK PANEL
(11) Quantity
of 1
LEFT DRAWER FRONT PANEL
(12) Quantity
of 1
MIDDLE DRAWER FRONT PANEL
(13) Quantity
of 1
RIGHT DRAWER FRONT PANEL
(14) Quantity
of 6
DRAWER SIDE PANEL
(15) Quantity
of 2
BACK PANEL OF TWO END DRAWER
(16) Quantity
of 2
BOTTOM PANEL OF TWO END DRAWER
(17) Quantity
of 1
BACK PANEL OF MIDDLE DRAWER
(18) Quantity
of 1
BOTTOM PANEL OF MIDDLE DRAWER
MENDELL HUTCH
Parts List
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware. Do not return to store/retailer.
Using a screw that is too long will cause damage.
Before beginning assembly, separate each type of screw. Carefully study the
screw diagrams below . You may receive extra hardware with your unit.

Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish . Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
Call Customer Service at 1-800-6 -5096
Do not return product to store, please call
Manufacturer for assistance, questions or
Parts.
Assembly Tool Required
No.2 Phillips Screwdriver (Not Included)
Figure 1
USE FLAT HEAD SHORT SCREW
(K) CONNECT STOPPERS (H) &
UPPER SHELF PANEL (7)
TOGETHER.
INSERT CAM LOCKS(C) INTO
PREDRILLED HOLES ON UPPER
VERTICAL PANELS (5).SCREW
CAM BOLT(A) INTO PREDRILLED
HOLES ON UPPER SHELF PANEL
(7). ATTACH UPPER VERTICAL
PANELS (5) TO UPPER SHELF
PANEL (7) BY SLIPPING WOOD
DOWEL(B) & CAM BOLT(A) INTO
CORRESPONDING PREDRILLED
HOLES UNTIL UPPER VERTICAL
PANELS (5) & UPPER SHELF
PANEL (7) MEET.SECURE BY
ROTATING CAM LOCK (C)
COUNTERCLOCKWISE WITH
PHILLIPS SCREWDRIVER.
INSERT CAM LOCKS(C) INTO
PREDRILLED HOLES ON LOWER
VERTICAL PANELS (6).SCREW
CAM BOLT(A) INTO PREDRILLED
HOLES ON LOWER SHELF PANEL
(8). ATTACH LOWER VERTICAL
PANELS (6) TO LOWER SHELF
PANEL (8) BY SLIPPING WOOD
DOWEL(B) & CAM BOLT(A) INTO
CORRESPONDING PREDRILLED
HOLES UNTIL LOWER VERTICAL
PANELS (6) & LOWER SHELF
PANEL (8) MEET.SECURE BY
ROTATING CAM LOCK (C)
COUNTERCLOCKWISE WITH
K
H
MENDELL HUTCH
Assembly Instructions

Figure 2
PHILLIPS SCREWDRIVER.
Figure 3
ATTACH FRONT UPPER BAR (4) &
ASSEMBLED UNIT IN THE STEP
1,2 TO LEFT SIDE PANEL (2) &
RIGHT SIDE PANEL ( ) BY
SLIPPING WOOD DOWEL(B) INTO
CORRESPONDING PREDRILLED
HOLES UNTIL FRONT UPPER BAR
(4) & ASSEMBLED UNIT IN THE
STEP 1,2 & LEFT SIDE PANEL (2)
& RIGHT SIDE PANEL ( )
MEET.USE ALLEN WRENCH (G) &
HEXAGON SOCKET BOLT (D) &
SPRING WASHER (E) & FLAT
WASHER (F) CONNECT
ASSEMBLED UNIT IN THE STEP
1,2 & LEFT SIDE PANEL (2) &
RIGHT SIDE PANEL ( )
TOGETHER .
MENDELL HUTCH
Assembly Instructions

Figure 4
INSERT CAM LOCKS(C) INTO
PREDRILLED HOLES ON
ASSEMBLED UNIT IN THE STEP
.SCREW CAM BOLT(A) INTO
PREDRILLED HOLES ON TOP
PANEL (1). ATTACH TOP PANEL
(1) TO ASSEMBLED UNIT IN THE
STEP BY SLIPPING WOOD
DOWEL(B) & CAM BOLT(A) INTO
CORRESPONDING PREDRILLED
HOLES UNTIL TOP PANEL (1) &
ASSEMBLED UNIT IN THE STEP
MEET.SECURE BY ROTATING CAM
LOCK (C) COUNTERCLOCKWISE
WITH PHILLIPS SCREWDRIVER.
USE ALLEN WRENCH (G) &
HEXAGON SOCKET BOLT (D) &
SPRING WASHER (E) & FLAT
WASHER (F) CONNECT
ASSEMBLED UNIT IN THE STEP
& TOP PANEL (1) TOGETHER .
Figure 5
INSERT BACK PANEL (10) INTO
ASSEMBLED UNIT IN THE STEP 4.
MENDELL HUTCH
Assembly Instructions

Figure 6
INSERT CAM LOCK(C) INTO
PREDRILLED HOLES ON
ASSEMBLED UNIT IN THE STEP
5.SCREW CAM BOLT(A) INTO
PREDRILLED HOLES ON BASE (9).
ATTACH BASE(9) TO ASSEMBLED
UNIT IN THE STEP 5 BY SLIPPING
WOOD DOWEL(B) & CAM BOLT(A)
INTO CORRESPONDING
PREDRILLED HOLES UNTIL BASE
(9) & ASSEMBLED UNIT IN THE
STEP 5 MEET.SECURE BY
ROTATING CAM LOCK (C)
COUNTERCLOCKWISE WITH
PHILLIPS SCREWDRIVER.
USE ALLEN WRENCH (G) &
HEXAGON SOCKET BOLT (D) &
SPRING WASHER (E) & FLAT
WASHER (F) CONNECT
ASSEMBLED UNIT IN THE STEP 5
& BASE (9) TOGETHER .
Figure 7
INSERTING ROUND HEAD SCREW
(L) INTO PREDRILLED HOLES
AND TIGHTENING WITH PHILLIPS
SCREWDRIVER(NOT
INCLUDED),AS SHOWN IN THE
STEP 7.
MENDELL HUTCH
Assembly Instructions

Figure8
USE FLAT HEAD LONG SCREW (J)
TO CONNECT DRAWER SIDE
PANELS (14) & LEFT DRAWER
FRONT PANEL (11) & BOTTOM
PANEL OF TWO END DRAWER
(16) & BACK PANEL OF TWO END
DRAWER (15) TOGETHER.
USE BOLT (N) TO CONNECT LEFT
DRAWER FRONT PANEL (11) &
KONB (M) TOGETHER.
USE FLAT HEAD LONG SCREW (J)
TO CONNECT DRAWER SIDE
PANELS (14) & RIGHT DRAWER
FRONT PANEL (1 ) & BOTTOM
PANEL OF TWO END DRAWER
(16) & BACK PANEL OF TWO END
DRAWER (15) TOGETHER.
USE BOLT (N) TO CONNECT
RIGHT DRAWER FRONT PANEL
(1 ) & KONB (M) TOGETHER.
MENDELL HUTCH
Assembly Instructions

Figure
Figure 10
USE FLAT HEAD LONG SCREW (J)
TO CONNECT DRAWER SIDE
PANELS (14) & MIDDLE DRAWER
FRONT PANEL (12) & BOTTOM
PANEL OF MIDDLE DRAWER (18)
& BACK PANEL OF MIDDLE
DRAWER (17) TOGETHER.
USE BOLT (N) TO CONNECT
MIDDLE DRAWER FRONT PANEL
(12) & KONB (M) TOGETHER.
Stick covers (O) to the cam locks
(C) surface.
PUSH DRAWERS INTO
ASSEMBLED UNIT IN THE STEP 7.
MENDELL HUTCH
Assembly Instructions

Figure 11
Figure 12
USE CONNECTION PLATES (I) &
FLAT HEAD SHORT SCREWS (K)
CONNECT HUTCH & DESK
TOGETHER.
NOW YOUR NEW DESK READY TO
USE.
ATTACH BRACKET(R) TO THE TOP
PANEL(1) WITH SCREW(S) FOR
BRACKET
DRILL 1/4 PILOT HOLES IN NEAR
PROXIMITY OF THE BRACKET(R)
ATTACHED TO THE TOP PANEL(1)
AND TAP THE PLASTIC
ANCHOR(P) INTO WALL.
FASTEN BRACKET(R) USING
SCREW(T) FOR WALL INTO THE
IK
K
MENDELL HUTCH
Assembly Instructions

Figure 13
PLASTIC ANCHOR(P).
Figure 14
MOVE THIS ITEM TO THE
FASTENED WALL BRACKET(R)
AND TIE IN BOTH BRACKET(R)
WITH PLASTIC CHAIN(Q) AS
SHOWN IN DIAGRAM.

Please immediately examine this product carefully. Any request for missing parts or damage replacement must
be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this
time frame.Parts will not be available for items arriving fully assembled. We do not recommend modifying
product(s) and we are not responsible for any damages due to product modification(s). If damages or missing
parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or replacement
merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central
time if you have product issues or email us at serv[email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[e-mail]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019

CAUTION
Max weight capacity for the hutch is 20 lb.
DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the
weights indicated may result in instability causing possible injury.
This unit contains a permanent warning sticker located on under side of top shelf or inside drawer.
Do not allow children under 16 years to move the cart.
Model: HO270200TX
MENDELL HUTCH
Southern Enterprises, Inc
600 Freeport Parkway, Suite 200
Coppell, Texas, 75019
Manufacture Date: