SEI HZ401800TX User manual

For assistance with assembly contact:
Southern Enterprises, Inc.
Customer Service 1-800-633-5096
[email protected]
www.seidal.com
HZ401800TX
Loring Entryway Storage Cubby
Assembly Instructions
PO#:

Loring Entryway Storage Cubby
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures.
Using the incorrect hardware will cause damage.
A
Quantity
of 1
Top Panel
B
Quantity
of 1
Left Side Panel
C
Quantity
of 1
Right Side Panel
D
Quantity
of 1
Left Side Apron
E
Quantity
of 1
Right Side Apron
F
Quantity
of 2
Fixed Shelf Panel
G
Quantity
of 2
Adjustable Shelf Panel
H
Quantity
of 1
Bottom Panel
I
Quantity
of 2
Rear Cross Panel
J
Quantity
of 1
Front Apron
K
Quantity
of 1
Back Panel
L
Quantity
of 5
Wicker Frame

M
Quantity
of 5
Wicker Bottom
1
Quantity
of 26
Cam Bolt
2
Quantity
of 26
Cam Lock
3
Quantity
of 8
Wood Dowel Ø5/16”x1-1/2”L
4
Quantity
of 6
Screw Ø5/32”x1”L
5
Quantity
of 26
Screw Ø1/8”x1/2”L
6
Quantity
of 8
Shelf Holder
7
Quantity
of 2
Anti-Tipping Hardware
8
Quantity
of 4
Adhesive Pad
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
Call Customer Service at 1-800-633-5096
Assembly Tool Required
No.2 Phillips Screwdriver
(Not Included)

“Please do not over tighten cam bolts,
please stop when you feel them tighten"
Figure 1
Attach left side apron (D) to left side panel
(B) by using screws (4) as shown.
Attach right side apron (E) to right side
panel (C) by using screws (4) as shown.
Make sure you are attaching the aprons
on the outside of the side panels.
Figure 2
Insert cam lock (2) into hole on rear cross
panel (I).
Screw cam bolt (1) into hole on bottom
panel (H).
Attach rear cross panel (I) to bottom panel
(H) by inserting cam bolt (1) into
corresponding hole until panels meet.
Tighten by rotating cam lock (2) clockwise
with Phillips screwdriver.
Loring Entryway Storage Cubby
Assembly Instructions
( 2 )
(1)

Figure 3
Insert cam locks (2) into holes on bottom
panel (H), rear cross panel (I), and fixed
shelf panel (F).
Screw cam bolts (1) into holes on side
panels (B) and (C).
Attach bottom panel (H), rear cross panel
(I) and fixed shelf panel (F) to side panels
(B) and (C) by inserting cam bolts (1) and
wood dowels (3) into corresponding holes
until all panels meet.
Tighten by rotating cam locks (2)
clockwise with Phillips screwdriver.
Figure 4
Insert cam locks (2) into holes on bottom
panel (H) and side panels (B) and (C).
Screw cam bolts (1) into holes on front
apron (J).
Attach front apron (J) to bottom panel (H)
and side panels (B) and (C) by inserting
cam bolts (1) into corresponding holes
until all panels meet.
Tighten by rotating cam locks (2)
clockwise with Phillips screwdriver.
H

Figure 5
Insert cam locks (2) into holes on side
panels (B), (C) and rear cross panel (I).
Screw cam bolts (1) into holes on top
panel (A).
Attach top panel (A) to side panel (B), (C),
and rear cross panel (I) by inserting wood
dowels (3) and cam bolts (1) into
corresponding holes until all panels meet.
Tighten by rotating cam locks (2)
clockwise with Phillips screwdriver.
Cover cam locks (2) with adhesive pads
(8) provided.
Figure 6
Attach back panel (K) to assembled unit
with screws (5).
Tighten screws (5) with Phillips
screwdriver.

Figure 7
Insert shelf holders (6) into holes on side
panels then place adjustable shelves (G)
onto shelf holders (6) as shown.
Figure 8
Attach the wicker bottoms (M) to wicker
frames (L).

Figure 9
Place wicker baskets into the assembled
unit.
Figure 10
Attach anti-tipping hardware (7) to back
panel as shown.
Tighten screws with Phillips screwdriver.
Mark two desired locations on wall and
drill two 3/16" holes.
Insert plastic anchors into the two drilled
holes on wall as shown. Lightly tap the
plastic anchors into the wall using a
hammer until plastic anchors are flush to
the wall.
Attach the anti-tipping hardware (7) to
plastic anchors on wall by using screws
as shown.
Move item close to the wall and connect
the anti-tipping hardware together using
the supplied plastic strap (7) as shown.
Anti-tipping hardware must be used for
this product to avoid tipping and
injury.

Figure 11
Now your Loring entryway storage cubby
is ready to use.

Please immediately examine this product carefully. Any request for missing parts or damage
replacement must be received within 90 days of your receipt of the product. Replacement, if
available, will be honored within this time frame.Parts will not be available for items arriving fully
assembled. We do not recommend modifying product(s) and we are not responsible for any
damages due to product modification(s). If damages or missing parts are not reported within 90
days of your receipt, we are under no obligation to provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm
Mon-Fri Central time if you have product issues or email us at [email protected]. Please ask for
customer service representative for issues involving damages or replacement parts. Please ask for
technical assistance representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[email protected]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
Page 4
Page11