SEI HZ030200TX User manual

For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]om
www.seifurniturestore.com
HZ030200TX
Drake Mirror/Hidden Coat
Rack
Assembly Instructions

A Quantity
of 1
Front Frame
B Quantity
of 1
Right Side Frame
CQuantity
of 1
Left Side Frame
DQuantity
of 1
Metal Tube
EQuantity
of 1
Bottom Metal Tube
FQuantity
of 1
Handle Divider Tube
G Quantity
of 1
Mirror Panel
H Quantity
of 1
Paper Panel
J Quantity
of 1
Wood Panel
K Quantity
of 1
Wood Shelf Panel
Drake Mirror/Hidden Coat Rack
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded surface like
carpet or a blanket. Check that you have all parts indicated. Call customer service if any hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures.
Using the incorrect hardware will cause damage.

1 Quantity
of 14
Short Bolt ：Ø1/4”×1/2” L
2 Quantity
of 1
Long Bolt ：Ø1/4”×1-1/4” L
3Quantity
of 1
Allen Wrench
4Quantity
of 4
Wood Screw: 4.0×1/2” L
5Quantity
of 8
Flat washer
6Quantity
of 12
Small Bolt: 4.0×3/8” L
7 Quantity
of 4
Tablet
8 Quantity
of 4
Long Tablet
9 Quantity
of 2
Long Wood screw ：4.0×1” L
10 Quantity
of 2
Wall anchor
11 Quantity
of 2
Wall brackets
12 Quantity
of 2
Plastic strap
Care and cleaning instructions:
Before use, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the finish.Avoid
rubbing or scratching the surface with rough or abrasive
objects.
For replacement parts or questions, please
Call SEI customer service at 1-800-633-5096
Assembly Tool Required
No.2 Phillips Screwdriver (Not Included)
Tool ist: 3/16" Drill Bit, Drill, Tape Measure and Pencil.

Figure 1
.
Put Mirror Panel(G) onto the Front
frame Frame(A).
Then put Paper Panel(H) onto the
Mirror Panel (G).
Put Wood Panel(J) onto the Paper
Panel(H)
Figure 2
Insert 8pcs Small Bolt (6) through
holes on Long Tablet (8) to attach
4pcs Long Tablet (8) onto Front
Panel (A) by Tool Required No.2
Phillips Screwdriver (Not Included).
Insert 4pcs Small Bolt (6) through
holes on Tablet (7) to attach 4pcs
Tablet (7) onto Front Panel(A) by
using- No.2 Phillips Screwdriver (Not
Included).
Drake Mirror/Hidden Coat Rack
Assembly Instructions

Figure 3
Attach Right Side Panel (C) onto
Front Panel (A) as shown.
Insert 4pcs Bolt (1) and 4pcs Flat
Washer (2) and then tighten by using
Allen Wrench (3).
Figure 4
Attach Left Side Panel (B) onto Front
Panel (A).
Insert 4pcs Bolt (1) and 4pcs Flat
Washer (2) tighten by using Allen
Wrench (3).

Figure 5
Insert 2pcs Short Bolt (1) through
holes on Metal Tube (D) to attach
Metal Tube (D) onto both side
Panels(B & C) by Allen Wrench (3).
Insert 2pcs Short Bolt (1) through
holes on Bottom Metal Tube (E) to
attach 1pc Bottom Metal Tube (E)
onto both side Panels(B & C) by
using Allen Wrench (3).
Figure 6
Insert 2pcs Short Bolt (1) through
holes on Handle Divider Tube (F) to
attach Handle Divider Tube (F) onto
Front Panel (A) byAllen Wrench (3).
Insert 1pc Long Bolt (2) through
holes on Metal Tube (D) to attach
Handle Divider Tube (F) onto Metal
Tube(D) by Allen Wrench (3).

Figure 7
Slowly push the Wood Shelf Panel
(K) into the both side Panels (B & C)
by hand
Insert 4pcs Wood Screw (4) through
holes on both side panels (B & C) to
attach Wood Shelf Panel (K) onto
both Side Panels (B & C) by Tool
Required - No.2 Phillips Screwdriver
(Not Included).
Figure 8
Find a desired location. Mark 2
locations for screws on wall
One screw (for each unit) must be
attached directly into a wall stud.
Wall anchor is not needed when
mounting to wall stud.
Drill one of the marking 3/16" hole
(for each unit).
.

Figure 9
Insert plastic anchors(10) into the
hole on wall as shown.(When doing
this, you will need a hammer to help
you)
Figure 10
Using the Phillips head screwdriver,
install screw (9) through holes on
Wall Brackets (11) into Wall Anchors
to attach Wall Brackets (11) onto
Wall Anchors (10).

Figure 11
Move this item close to the fastened wall
brackets and tie in brackets and side
frame with plastic straps(12) as shown in
diagram.
Check to make sure the strap is
securely laced and locked to the
brackets.
Figure 12
Now your Drake Mirror/Hidden Coat
Rack is ready to use!
12

Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time
frame.Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s)
and we are not responsible for any damages due to product modification(s). If damages or missing parts are not
reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central time
if you have product issues or email us at serv[email protected]. Please ask for customer service representative for
issues involving damages or replacement parts. Please ask for technical assistance representative for any issues
with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[email protected]om
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019