Seifert FL 4620A User manual

Version Nr. 4 - 30.10.2016 Doc. Nr. 994620A4000 1 / 6
Table of Content FL 4620A 230V
1. User manual 2 ...................................................................................................................
2. Legal regulations 2 ...........................................................................................................
3. Safety instructions 3 ........................................................................................................
4. Technical data 4 ................................................................................................................
6. Cut out dimensions 5 .......................................................................................................

Version Nr. 4 - 30.10.2016 Doc. Nr. 994620A4000 2 / 6
1. User manual
This instruction manual contains information and instructions to enable the user to work safely,
correctly and economically on the unit. Understanding and adhering to the manual can help one:
Avoid any dangers.
●
Reduce repair costs and stoppages.
●
Extend and improve the reliability and working life of the unit.
●
PLEASE ENSURE TO USE THE RIGHT VERSION OF THE INSTRUCTION MANUAL SUITABLE FOR
YOUR UNIT.
Conditions of use
󰾬The unit is to be used exclusively for the dissipation of heat from control cabinets and enclosures in
order to protect temperature sensitive components in an industrial environment. To meet the
conditions of use, all the information and instructions in the instruction manual must be adhered to.
General danger
Indicates compulsory safety regulations which are not
covered by a specific pictogram such as one of the following.
High electric voltage
Indicates electric shock danger.
Important safety instruction
Indicates instructions for safe maintenance and operation of
the unit.
Attention
Indicates possible burns from hot components.
Attention
Indicates possible damage to the unit.
Instruction
Indicates possible danger to the environment.
2. Legal regulations
Liability
The information, data and instructions contained in this instruction manual are current at the time of
going to press. We reserve the right to make technical changes to the unit in the course of its
development. Therefore, no claims can be accepted for previously delivered units based on the
information, diagrams or descriptions contained in this manual. No liability can be accepted for
damage and production caused by:

Version Nr. 4 - 30.10.2016 Doc. Nr. 994620A4000 3 / 6
Disregarding the instruction manual
●
Operating error
●
Inappropriate work on or with the unit
●
The use of non-specified spare parts and accessories
●
Unauthorised modifications or changes to the unit by the user or his personnel
●
The supplier is only liable for errors and omissions as outlined in the guarantee conditions contained in
the main contractual agreement. Claims for damages on any grounds are excluded.
3. Safety instructions
Upon delivery the unit is already meeting current technical standards therefore it can be safely taken
into operation. Only trained specialists are allowed to work on the unit. Unauthorised personnel must
be prohibited from working on the unit. Operating personnel must inform their superiors immediately if
any malfunction of the unit becomes apparent.
Please note that before starting to work on or with the unit, a procedure must be carried out inside the
cabinet on which the unit is to be mounted.
Before commencing work inside the cabinet, the control cabinet manufacturer's instruction must be
read with regards to:
Safety instructions.
●
Instructions on taking the cabinet out of operation.
●
Instructions on the prevention of unauthorised cabinet reconnection.
●
The electric equipment meets the valid safety regulations. One can find dangerous voltages (above 50
V AC or above 100 V DC)
Behind the control cabinet doors.
●
On the power supply in the unit housing.
●
The unit has to be fused according to the type plate and the wiring diagram, and must be protected
externally from overloading and electrical faults via suitable protective devices such as ground fault
protection breakers.
Danger through incorrect work on the unit
The unit can only be installed and maintained by technical competent and
qualified personnel, using only supplied material according to the supplied
instructions.
󰾬
Danger from electrical voltage
Only specialised personnel are allowed to maintain and clean the unit. The
personnel must ensure that for the duration of the maintenance and cleaning, the
unit is disconnected from the electrical supply.
Attention
Damage to the unit through the use of inappropriate cleaning materials. Please do
not use aggressive cleaning material.
Instruction
Damage to the environment through unauthorised disposal. All spare parts and
associated material must be disposed according to the environmental laws.

Version Nr. 4 - 30.10.2016 Doc. Nr. 994620A4000 4 / 6
4. Technical data
Order Number 4620A4000
Temperature range -10°C - +55°C
Air volume flow 230 m³/h @ 50Hz / 270 m³/h @ 60Hz
Static pressure 115 Pa @ 50Hz
155 Pa @ 60Hz
Dimension HxWxD 250 x 250 x 124.2 mm
Weight 1.5 kg
Cut out dimensions 223 +1.5 x 223 +1.5 mm
Voltage / Frequency 230V 50/60Hz
Rated current 0.134 A @ 50Hz
0.160 A @ 60 Hz
Power consumption 32 W @ 50Hz
36 W @ 60 Hz
1.5 - 2.5 mm
Filter class G3 gemäß EN 779
Installation Elastic clips or by 4 self-threading screws
Noise level 50 dB(A) @ 50Hz
55 dB(A) @ 60 Hz
IP 54
CE, cURus

Version Nr. 4 - 30.10.2016 Doc. Nr. 994620A4000 5 / 6
6. Cut out dimensions

Version Nr. 4 - 30.10.2016 Doc. Nr. 994620A4000 6 / 6