Seiko I Infotech IP-260 User manual

User's Guide
Dryer 64
for Solvent Ink Inkjet Printer IP-6600
IP-260/IP-263
Seiko I Infotech Inc.
Read this User's Guide to use the printer safely and
properly. Keep this manual in a place where you
can quickly access it at any time.
U00087124400

IP-260 / IP-263 Dryer 64 for Solvent Inkjet Printer IP-6600 User's Guide
Documents Number U00087124400
First Edition, March 2004
Copyright © 2004 by Seiko I Infotech Inc.
All rights reserved
Seiko I Infotech Inc. reserves the right to make changes without notice to the specifications and
materials contained herein and shall not be responsible for any damages (including consequential)
caused by reliance on the materials presented, including but not limited to typographical, arithmetic,
or listing errors.
Please address any questions, comments, and suggestions to:
Seiko I Infotech Inc.
Blue Sphere Nihonbashi Bldg.
11-1, NihonbashiTomizawa-cho,
Chuo-ku,Tokyo 103-0006, Japan
This manual acknowledges the following trademarks:
SII is a trademark of Seiko I Infotech Inc.
All other trademarks are the properties of their respective companies.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.

i
Thank you for purchasing the IP-260/263 Dryer 64 that is
exclusively used for our Solvent Inkjet Printer IP-6600.
The unit is designed to effectively dry media (ink) printed by and
released from the printer. This aims to maximize the fast printing
performance (16 m2/hour) that characterizes our Solvent Inkjet
Features:
Printer IP-6600.
•High-speed media (ink) drying in response to fast printing (16
m2/hour.
This warm air-based high-speed media (ink) drying is achieved by
partitioning the media path of the IP-6600 printer, ranging from the
media release guide to the media reel, from the air outside.
Note:
16 m2/hour is the value when the printing width is 50 inches or more.
•Drying time preset function up to 12 hours
Equipping a timer allows users to preset the drying time by each hour
up to 12 hours, resulting in effective drying and power saving.
•Direct media release function
Only switching the media path of the IP-6600 to the direct media
release allows users to directly release media from the rear side of
the IP-6600 printer while drying it.
Note:
Thoroughly drying ink itself is additionally needed for media to which
laminate post processing is applied. Hence, it is not recommended the
laminate post processing be applied just after the media is released.
Some media cannot be dried up sufficiently depending on
a type.
In case of that, set "SCANTIME" on the operation panel of
the printer to dry the media sufficiently.
Introduction

ii
Users can install the dryer in the IP-6600. To maximize the drying
performance of this unit, correctly use it in accordance with the
instructions described in this manual.
The following items should be read before reading Section 1.
- Deliverables
- Safety precautions
- Handling precautions
- Manual legent (Notation rules)
Read these items to use the dryer safely and properly. Keep this
manual in a place where you can quickly access it at any time.

iii
Deliverables
Make sure that the following items are present.
If any parts are missing or damaged, contact the shop where you
purchases the product or the service dealer.
Partition cloth <1>
Components
Drying guide plate <1>
Dryer <1>
User’s Guide (This manual) <1>

iv
Example of symbols:
This symbol ( ) denotes items that require special care
while executing a certain procedure or operation.
This symbol ( ) denotes items that are forbidden.
This symbol ( ) denotes items you should follow to
prevent accidents or injury.
Safety Precautions
The following symbols are used in this manual to ensure the proper
use of the dryer and to prevent the dryer from being damaged.
Follow the instructions marked with these symbols.
Minor personal injury or product and/or
peripheral damage:
Failure to follow the guidelines marked with
this symbol could result in minor personal
injury or product and/or peripheral damage.
Serious personal injury or death:
Failure to follow the guidelines marked with
this symbol could result in serious personal
injury or death.
WARNING
CAUTION

v
Use the power supply voltage specified on the nameplate. DO NOT
plug several devices into a single electrical outlet as this might result in
fire or electric shock.
Make sure the dryer is well grounded. If not, a short circuit may cause
fire or electrical shock.
DO NOT disassemble or remodel the dryer. DO NOT repair the dryer
by yourself. Doing so may cause fire, electric shock or other accidents.
DO NOT damage, break, process, or heat the power cable. Using a
damaged power cable may cause fire or electric shock.
NEVER use the dryer in a place of extreme humidity or any place where
it can possibly be splashed by any liquids. If any liquids get into the
dryer, it could lead to fire, electric shock, or other serious accidents.
DO NOT remove the covers attached to the dryer because they contain
high-voltage and extremely hot parts. Careless removal might result in
an electric shock or burn.
DO NOT allow metal or liquids to touch the internal parts of the dryer.
Doing so may cause fire, electric shock, or other accidents.
DO NOT disconnect or connect the power cable with wet hands. Doing
so may lead to electric shock.
Turn the dryer off and unplug the power cable immediately after and
during an electric storm.
WARNING

vi
Handle the dryer with care because they are very heavy. If you drop
them, it could lead to personal injury.
Hold the electric cable by the plug when connecting or disconnecting it.
Failure to do so may cause the cable to fray or break which could lead to
electric shock and/or fire.
DO NOT install the dryer in unstable places such as on an fastage and an
inclining place.
If you drop or fall the dryer, it could lead to personal injury.
The heater will be hot.
Pay attention not to touch and not to be burned.
In order to ensure the safe operation of the printer, read all of the cautions
and warnings contained throughout this manual.
CAUTION
Power OFF the dryer and unplug the power cord from the power outlet
in any of the following cases:
•When putting your hands inside the dryer.
• Smoke, strange noise or smells generate from the dryer.
•Apiece of metal or any liquid touches the internal parts or slot of
the dryer.
• An error requiring service by a service center occurs.
WARNING

vii
Handling Precautions
Power Supply
1. Install the dryer near an easily accessible electrical outlet.
2. Do not provide power to the dryer through the same power line
as for noise-generating devices, such as a motor.
3. The power supply voltage must be 230 VAC.
4. Connect the power cable to an electrical outlet. Do not plug
several devices into a single electrical outlet.
Dryer
1. Do not place anything on top of the dryer. Do not rest your
elbows on the dryer.
2. Do not clean the surface of the cover with benzene or paint
thinner. The coating may come off or deteriorate.
Wipe the cover clean with a soft cloth. If the cover is very dirty,
use a cloth moistened with a neutral detergent.
3. This dryer is prepared only as the media (ink) drying device for
the IP-6600 printer.
Do not use any other dvices or any other pursoses.
4. Remove the protection sheet attached on the surface of the dryer
before use.
Limitations
1. When the dryer is used, the tension winding cannot be used.
2. When the dryer is used, the media saving mode function cannot
be used.

viii
Marks
Boxes marked with a "WARNING" describe points of caution for
avoiding serious personal injury.
Boxes marked with a "CAUTION" describe points of caution for
avoiding injury to yourself or damage to the dryer.
Boxes marked with a note describe precautions while handling the
dryer.
HINT: Hint mark
The hint symbol describes operations that make using or
handling the dryer easier.
Reference mark
This mark is followed by a reference section or page number.
Manual Legend (Notational rules)
This manual uses the notational rules for marks.
NOTE
HINT
WARNING
CAUTION

CONTENTS-1
TABLE OF CONTENTS
Introduction .....................................................................................................i
Deliverables ..................................................................................................iii
Safety Precautions........................................................................................iv
Handling Precautions...................................................................................vii
Manual Legend (Notational rules)...............................................................viii
Section 1 Part Names and Functions 1
Section 2 Installing 3
2-1 Required Installing Space................................................................3
2-2 Operational Environment.................................................................4
2-3 Pluging the Power Cord and Turning ON/OFF the Dryer................ 5
Section 3 Using the Operation Panel 6
3-1 Part Names and Functions..............................................................6
Section 4 Installing / Uninstalling Media 8
4-1 Installing Media................................................................................8
4-2 Uninstalling Media .........................................................................12
Section 5 Using the Timer 14
Section 6 Attaching the Exhaust Attachments 15

CONTENTS-2
Section 7 Maintenance and Cleaning 16
7-1 Maintenance ..................................................................................16
7-2 Cleaning Outer Case.....................................................................16
Section 8 Specifications 17

CONTENTS-3
Figure
Figure 1-1 External View and Part Names of the Dryer...................1
Figure 2-1 Installing Space for the Dryer...........................................3
Figure 3-1 External View and Part Names of the Operation Panel...6

1
Section 1 Part Names and Functions
This Section explains part names and functions of the dryer.
1. Partition cloth
2. Drying guide plate
3. Dryer
Figure 1-1 External View and Part Names of the Dryer
(2-2)
(1-3)
(1-2)
(1-1)
(2-1)
(2-2)
(3-1)
(3-2)
(3-4)
(3-4)
(3-8)
(3-5)
(3-6)
(3-7)
(3-3)

2
No. Name Description
1 Partition Cloth The cloth that partitions the front of the dryer from the
external air to increase drying efficiency.
1-1 Partition Cloth
Attachment Hook The metallic fitting that attaches the partition cloth to the front of the printer.
1-2 Partition Cloth Bar
(Front) The bar that attaches the partition cloth to the front of the printer.
1-3 Partition Cloth The bar that attaches the partition cloth to the bottom of
the printer.
2 Drying Guide Plate The media path guide plate for using the dryer.
2-1 Drying Guide
Attachment Plate The attachment plate that fits the drying guide plate to the winding unit.
2-2 Drying Guide Sliding
Rail Slide the drying guide plate upward to set the media to the winding unit.
3 Dryer The heater is builtin and the dryer sends warm wind by
fans to dry up the printed media.
3-1 Operation Panel The operation panel for the dryer.
For details, see Chapter 3 Using the Operation Panel.
3-2 Breaker Switch The switch that turns ON/OFF the dryer power.
3-3 Power Cord The power cord that supplies power to the dryer. The one end is secured to the dryer. Specification: 207
to 253 VAC, 50 Hz ± 1 Hz
3-4 Handle The handle used for moving the dryer.
The handles are attached to both sides of the dryer.
3-5 Upper fans The fans that are attached to blow air to the heater for
generating warm air.(Suction type)
3-6 Lower fans The fans that circulate warm air into the dryer.
(Suction type)
3-7 Casters The casters used for moving the dryer.
The caster has a lock and release function.
3-8 Exhaust Attachments
Attaching Part The part to which the exhaust attachments (option) are attached.

3
Section 2 Installing
This Section explains how to install the dryer.
2-1 Required Installing Space
Keep the following installing space for the dryer.
Figure 2-1 Installing Space for the Dryer
400 400
(Front)
(Rear)
Height: 1700
(Unit: mm)
IP-6600
Dryer

4
2-2 Operational Environment
Use the dryer under the following operational environment.
Item Specifications
Operation temperature and
humidity range Temperature: 15 to 30 °C Humidity : 30 to 70%RH (No condensing)
Standby temperature and
humidity range Temperature: 5 to 35 °C Humidity : 10 to 80%RH (No condensing)
Fine particles level Equivalent to office environment
Ventilation Ventilation facilities are recommended for
deodorizing
Power supply
Power voltage : 230 VAC ± 10%
Power frequency: 50 Hz ± 1Hz
Grounding : D class grounding
(The 3rd class grounding)

5
2-3 Pluging the Power Cord and Turning ON/OFF the Dryer
Plug the power cord of the dryer into the inlet after installing the dryer in the printer.
Follow the procedures below.
1. (○)Verify that the breaker switch of the dryer is turned off , and plug
one edge of the power cord into the inlet matched with the
specifications.
2. (│)Turn on the breaker switch of the dryer.
NOTE
The power specifications of the dryer are shown below.
-Power voltage: 230 VAC ± 10 %
-Power frequency: 50 Hz ± 1 Hz
-Grounding: D class grounding (The 3rd class grounding)
Always use power supply matched with the power specifications.
Breaker Switch
Power Cord

6
Section 3 Using the Operation Panel
3-1 Part Names and Functions
Figure 3-1 External View and Part Names of the Operation Panel
(6) (7) (1) (2) (3) (5) (4)
(8) (9)
No. Name Description
1Heater temperature
preset dial
(NOTE1)
Presets heater temperature using this dial. The
heater turns on and off automatically to keep the
preset temperature.
Preset Range: 30 to 60 ° C (thermistor)
2FAN (upper) airflow
preset dial
(NOTE1)
Presets the airflow of the upper FANs.
3FAN (lower) airflow
preset dial
(NOTE1)
Presets the airflow of the lower FANs.
4 Timer switch Selects use or not use of the off-timer.
5 Timer preset dial
Presets time up of the off-timer.
Range: 1 to 12 hours
Unit: 1 hour
Only displays preset time for the off-timer.
Judges the time up by the time up lamp (red).
6 Power lamp (Orange) Displays the power on state of the dryer. Lit: Displays the power on state.
Unlit: Displays the power off state.
(NOTE1) Turn the heater temperature preset dial to the highest and turn the fan (upper and lower)
airflow preset dial to the low or middle to use the dryer ’s performance maximum.
The preset temperature attainment lamp may not light even when the heater temperature
preset dial is turned to the highest. However, temperature is saturated to the maximum
temperature in approx. 20 minutes. When using media delicate for heating, adjust the
heater temperature preset dial to low.

7
No. Name Description
7Preset temperature attainment lamp (Green)
(NOTE2)
Displays that the temperature has attainted the
preset temperature.
Lit: Displays the temperature attains the preset
temperature. (Heater power off)
Unlit: Displays the temperature does not attain
the preset temperature.
8Time up lamp (Red)
(NOTE3)
Displays the time up state.
Lit: Displays that the heater is turned off due to
the time up.
Unlit: Displays that the timer is in the count up
state. (Heater on)
9 Timer active lamp Displays the use state of the timer. Lit: Displays that the timer is in use state.
Unlit: Displays that the timer is not in use state.
(NOTE2) When the heater temperature dial, FAN (upper) airflow preset dial, and FAN (lower) airflow
preset dial are turned maximum, the preset temperature attainment lamp may not be lit.
The dryer is designed so that the fan’s airflow power is slightly stronger than the heater ’s
heating power to maximize the drying up performance. (The heater is always turned on
because the preset temperature cannot attain the maximum temperature 60°C.)
Even though the preset temperature attainment lamp is not lit, the temperature attains the
maximum temperature in approx. 20 minutes after turning the breaker on.
(NOTE3) Even when the time up lamp is lit, the fans (upper and lower) are functioning based on
the preset dials. (The heater is turned off.)
The preset temperature attainment lamp may also not be turned of f due to remaining
heat.