SELT Refleksol 85 SA User manual

2. Sun protection screen Refleksol
2.4 Refleksol 85 SA and 85 MA
TECHNICAL AND OPERATIONAL DOCUMENTATION
INSTALLATION AND OPERATING MANUAL
AND INSTRUCTIONS FOR SAFE USE
2.13
DT-E
DTE
DT-E

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 2 / 19
PRODUCT NAME:
SUN PROTECTION SCREEN
REFLEKSOL 85 SA and 85 MA
PRODUCT MANUFACTURER’S MARKING:
Manufacturer’s name:
SELT Sp. z o. o.
Manufacturer’s head office:
45- 449 Opole, ul. Wschodnia 23A
Plant address:
Wydział Żaluzji Fasadowych i Refleksoli [Façade and External Textile Roller Blind Department]
45- 449 Opole, ul. Wschodnia 23A
Contact details:
Tel: [phone] (secretariat)
Fax: [phone]
Website
www.selt.com
E-mail:
[email protected]
PRODUCT SAFETY MARKING:
Product conforms to CE safety requirements.
This Technical and Operational Documentation:
Is valid from: 01 April 2017
Is valid for product versions designated above

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 3 / 19
TABLE OF CONTENTS
1. Introduction ............................................................................................................................................... 4
1.1. Product safety tips................................................................................................................................. 4
1.2. Notes on symbols and marks................................................................................................................. 4
1.3. Definitions ............................................................................................................................................. 4
1.4. Subject, designation and contents of the documentation .................................................................... 5
2. Product technical information ................................................................................................................... 6
2.1. Technical parameters ............................................................................................................................ 6
2.2. Product characteristics.......................................................................................................................... 6
3. Product transport and storage................................................................................................................... 7
3.1. Completeness and qualitative state of delivery .................................................................................... 7
3.2. General conditions of product trnaport and storage ............................................................................ 7
3.3. Descriptions that have to be put obligatory on the product packaging................................................ 7
4. Product installation.................................................................................................................................... 8
4.1. Requirements for safe installation at heights ....................................................................................... 8
4.2. Preparation to installation..................................................................................................................... 8
4.3. General guidelines for installation......................................................................................................... 9
4.4. Installation tools .................................................................................................................................... 9
4.5. Installation............................................................................................................................................. 9
4.5.1 Installation of wall-ceiling brackets .......................................................................................................... 9
5. System operation and product safety...................................................................................................... 12
5.1. General safety requirements............................................................................................................... 12
5.2. Safety requirements connected with particular conditions and places of product use...................... 12
5.3. Operation safety.................................................................................................................................. 13
5.4. Supervision of safe product use .......................................................................................................... 14
6. System use and maintenance .................................................................................................................. 14
6.1. Using the product in accordance with its intended use ...................................................................... 14
6.2. Instructions for non-professionals....................................................................................................... 14
6.3. Technical inspections, maintenance and service ................................................................................ 15
7. General warranty conditions ................................................................................................................... 16
7.1. Exclusions for warranty ....................................................................................................................... 16
8. Complaints/ technical faults .................................................................................................................... 17
8.1. Complaints........................................................................................................................................... 17
8.2. Technical faults.................................................................................................................................... 17
9. Product disassembly / utilisation / disposal ............................................................................................ 17
10. Marking and labelling the product with the CE mark .............................................................................. 18
10.1. Product compliance with the CE standard .......................................................................................... 18
10.2. Information accompanying the CE marking ........................................................................................ 18
11. Information on safety elements installation............................................................................................ 19

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 4 / 19
1. INTRODUCTION
1.1. PRODUCT SAFETY TIPS
The product was manufactured in accordance with the latest know-how in the area of constructing and manufacturing and
is delivered in condition allowing for its safe use.
Safe construction of the product is achieved by:
No.
Subject
European legal basis
Polish legal basis
1
Internal blinds. Performance
requirements including
safety
EN 13120:2009+A1:2014
PN-EN 13120+A1:2014-04
2
General product safety
Directive 2006/95/EC of the European
Parliament and the Council
DZ.U. [Journal of Laws] of 12 December
2003, no. 229, item 2275 as amended.
Linked documents: manual of installation and use.
1.2. NOTES ON SYMBOLS AND MARKS
The below symbols (icons) denote particularly important information concerning threats and safety.
Icon
Icon meaning
Information
INFORMATION
Prior to using the product, its operating manual should be read.
Following the operating manual guarantees:
- failure-free use of the product,
- warranty coverage against product defects.
Keep the operating manual for safety of people.
INFORMATION
No harmful or dangerous consequences for people or facilities.
ATTENTION!
A situation likely to cause product damage or other damage.
No threat for people.
WARNING!
Threat of danger
DANGER!
This symbol denotes all information concerning danger, failure to observe
which brings about threat to human life and health. Risk: threat of serious injury
or death. Dangerous operation which may cause injuries or product damage.
WARNING
Threat of strangulation
1.3. DEFINITIONS
The terms and definitions used within this documentation shall mean:
ROLLER BLIND: internal blind, installed in front of a window or in a window or in any place within the internal surface of a
building, where stretching and pulling (lifting and lowering) of the fabric is performed with the use of a control mechanism
(manually by chain).
FABRIC: part of the product made from fabric or other material; it is put into motion with the use of a control mechanism
assuring the product fulfills its function.

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 5 / 19
1.4. SUBJECT, DESIGNATION AND CONTENTS OF THE DOCUMENTATION
Products manufactured by SELT Sp. z o. o. are the subject of this documentation.
Operating manual and instructions for safe use along with the manual for the engine, switches
and control shall be submitted to the end user.
IMPORTANT INFORMATION REGARDING SAFETY
WARNING –FOLLOWING THE MANUAL IS ESSENTIAL FOR SAFETY OF PEOPLE
KEEP THIS MANUAL
The documentation is valid jointly with the information concerning a specific product, which is
available on the website www.selt.com
The documentation includes:
important recommendations concerning product installation, use and maintenance,
important recommendations concerning product transport and storage,
tips following which will assure long-time and fault-free use of the product.
SELT Sp. z o. o. shall not bear responsibility for damage resulting from failure to follow recommendations included in the
documentation.
In order to further improve the product, SELT Sp. z o. o. reserves the right to introduce changes which, while maintaining
the essential technical parameters, shall be deemed purposeful for improving product operation quality and safety of use.
SELT Sp. z o. o. with a head office in Opole shall hold the copyrights to this documentation. The documentation cannot be
used without permission, either partially or as a whole, for any concurrent business activity nor can it be made available to
third parties.

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 6 / 19
2. PRODUCT TECHNICAL INFORMATION
Product technical specification is available at www.selt.com after log in.
2.1. TECHNICAL PARAMETERS
Refleksol 85 SA and Refleksol 85 MA
Dimensions*:
width
height
Cassette
86 mm
85 mm
Refleksol 85 SA manual drive (chain)
2200 mm
2500 mm
Refleksol 85 MA manual drive (chain)
2500 mm
3000 mm
Refleksol 85 SA/MA:
Available in free-hanging version
Manual drives:
Plastic ball chain
Available lengths: 240 cm, 360 cm with connectors for optional shortening
Installation:
Intended use
Only internal
Installation place
To the ceiling or wall
*Maximum dimensions of the system depend on the fabric used, does not apply to Refleksol 85 SA
2.2. PRODUCT CHARACTERISTICS
Refleksol 85 is a free-hanging system designed for shading modern interiors. Can be installed to the ceiling or wall, as well
as in a window niche. Elegant design of small square cassette made from extruded aluminium. System is equipped with
spring-chain mechanism which ensures smooth operation of the blind. System is available in two variants: Refleksol 85
Manual and Refleksol 85 Semi-Automat, which due to unique shape of the bottom bar enables operation of the blind
without using the chain. Gentle touch is enough for the blind to start rolling itself up.
Product types –REFLEKSOL 85 SA/MA:
Refleksol 85 SA manual drive with spring mechanism with automatic rolling up and soft-stop function; free-
hanging, internal application,
Refleksol 85 MA manual drive (chain); free-hanging, internal application,
The products are characterised by the following qualities:
they are designed for installation in the window area,
they limit the sun light coming into the room,
they provide disperse light in the room
they prevent rooms from overheating, thus contributing to the improvement of thermal comfort in rooms,
they help to limit the costs of air conditioning in the rooms,
they limit the noise transmission to the inside
they do not emit any toxic substances during their work,
the construction of the product and driver allows to stop the fabric safely at any height within the up-down work
area and stay there suspended,

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 7 / 19
casings for the movable parts were designed and performed in a manner assuring safety for operators as long as
they are used properly,
product is delivered with elements and marking allowing for safe installation of the chain and its adjustment to
the requirements specified in norm for preventing strangulation.
In Refleksol products with big dimensions, when there is the need to connect the fabric stripes by
welding (horizontal fabric connections), there might appear the “memory effect” of the fabric. The
rolling of the fabric does not cause improper functioning of the system and is not a defect of the
product.
3. PRODUCT TRANSPORT AND STORAGE
3.1. COMPLETENESS AND QUALITATIVE STATE OF DELIVERY
Selt Sp. z o. o. makes every effort to ensure that the goods are produced in accordance with the order. To check the
completeness of the product is purchaser’s duty and it should be conducted at the time of delivery. Any discrepancies of
the product with the order should be reported immediately to the driver/warehouseman/installers and noted in the proof
of delivery at the risk of losing warranty. Checking the quality of the apparent defects should be done by the purchaser at
the time of delivery. As apparent defects are considered mechanical damages, scratches, cracks, etc. Any discrepancies in
quantity or possible replacements of parts being the evident result of Selt Sp. z o. o. fault, the company agrees to
supplement or replace in the shortest possible time.
3.2. GENERAL CONDITIONS OF PRODUCT TRNAPORT AND STORAGE
List:
The product is factory-packed in a cardboard box to prevent its damage during storage, transport and during its
transportation to the place of final assembly,
For the transport purposes, the products should be set in accordance with the arrows on the packaging,
Do not store the products in a number of layers greater than 2 due to the possibility of crushing the package
which in turn can lead to permanent damage of the product,
Products placed on the means of transport must be secured against movement and damage during transport (e.g.
spacers, safety belts, etc.),
During transportation the products must be protected from the rain or snow,
Storage places should be dry, airy and protected from the harmful effects of weather conditions (sun,
rain, etc.),
Where the weight of the product exceeds 25kg and its transportation to the place of final assembly
must be carried out by at least two persons.
3.3. DESCRIPTIONS THAT HAVE TO BE PUT OBLIGATORY ON THE PRODUCT PACKAGING
Before the installation and use of the product its Technical and operation documentation, available at
www.selt.com/doc-en, should be read carefully.
On Refleksol 85 SA and Refleksol 85 MA packaging the below warning is included.
Moreover, packaging with safety devices are marked with the following note:
Y o u n g c h i l d r e n c a n b e s t r a n g l e d w h e n t h e s a f e t y d e v i c e i s n o t i n s t a l l e d a n d a d j u s t e d .
R e a d c a r e f u l l y t h e i n s t r u c t i o n s a n d i n s t a l l a c c o r d i n g l y .
WARNING
- Young children can be strangled by loops in pull cords, chains,
tapes and inner cords that operate the product.
- To avoid strangulation and entanglement, keep cords out of the
reach of young children. Cords may become wrapped around a
child’s neck.
- Move beds, cots and furniture away from window covering
cords.
Do not tie cords together. Make sure cords do not twist and
create a loop.

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 8 / 19
4. PRODUCT INSTALLATION
The following part covers general requirements of the product installation.
Proper installation is necessary for efficient operation of the product. SELT Sp. z o. o. recommends to use services of skilled
installation crews what guarantees the Purchaser proper installation.
General requirements for safe installation
it is necessary to follow general rules of construction art,
it is necessary to follow health and safety regulations, especially concerning work with electricity and at heights,
the product must be mounted in mechanical way (foams, glues and similar products are not allowed as fastening
materials),
the product should be mounted to permanent elements of the building (walls, lintels, steel structures, aluminum
structures, window frames),
the base where wall-ceiling brackets are mounted should be durable construction (concrete, brick, etc.),
it is not allowed to mount the product on building structures that does not provide sufficient load-bearing
capacity,
product should be installed on even and dry wall surfaces that at the same time ensure proper strength and are
completed according to general rules of building art,
in case of constructions made of metal, in which components are welded together according to art of joining
metal parts, installation is made to the structures of sufficient wall thickness,
before starting the installation remove all unnecessary elements from the installation area,
before starting the installation all mechanisms redundant for the drive operation should be immobilized.
4.1. REQUIREMENTS FOR SAFE INSTALLATION AT HEIGHTS
Installation of the product, because it requires performing work at heights, is particularly dangerous
because it poses a high risk of danger to human health and safety and in particular fall from height.
The purchaser is obliged to conduct the installation of the product according to health and safety regulations applicable in a
given country. The responsibility of the purchaser is to develop a plan for health and safety protection during installation.
Purchaser should determine specific requirements of health and safety when working at height, and especially to ensure:
direct supervision of work execution by the designated person (e.g. the foreman),
adequate safeguards measures, in particular protective equipment against falls from height,
detailed instruction of employees performing work at heights,
necessity to use ladders with appropriate quality and safety certificates, scaffoldings, safety buckles, platforms
with adequate strength for anticipated load.
Work at heights that requires using personal protective equipment against falls from height, must be performed by at least
2 people.
4.2. PREPARATION TO INSTALLATION
unpack product and check if it contains all necessary elements for installation,
before starting the installation check the dimensions of window opening with specifications on the packaging,
make sure that the base where product will be mounted provides sufficient bearing capacity for safe installation
and operation of the product.
Attention! Pins, screws or bolts to secure the product to the structure depend on the type of substrate,
and therefore are not included with the product and its purchase has to be done by the buyer or
installer.

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 9 / 19
4.3. GENERAL GUIDELINES FOR INSTALLATION
mounting of the brackets and covers should be done with appropriate bolts and pins (they are not included with
the product),
in case of reinforced concrete lintel or solid bricks, dowels should be used for mounting. Make sure their size is
correctly selected for bearing capacity,
depending of the type of the wall structure appropriate mounting system should be selected,
longitudinal axis of the product cassette should be leveled, otherwise the product will not roll correctly
the product should be protected against any stains made by e.g. silicon, mortar or mounting foam, which may
cause its malfunction,
using any chemical substances containing bituminous substances or any other substances making reactions with
the product is forbidden.
Improper installation may cause hazardous situation for the user.
4.4. INSTALLATION TOOLS
List:
drills for metal and concrete,
hummer drill,
ladder/scaffolding,
screwdriver,
hammer,
tape measure,
Pencil/pen,
Spirit level,
Allen wrenches,
cutter.
4.5. INSTALLATION
Installation and operating manual and instructions for safe use is available after log in on www.selt.com.
Fabric can move on the roller tube and bottom bar during incorrect transport of the product (in vertical
position). Therefore one should check fabric placement on the bottom bar and roller tube before
commencing the installation.
4.5.1 INSTALLATION OF WALL-CEILING BRACKETS
1. Measure and mark places for the installation of
brackets.
Img. 1

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 10 / 19
2. With spirit level mark vertical level of the bracket
axis.
Img. 2
3. Install first bracket to the wall / ceiling (detail –
ceiling installation)
Img. 3
4. Measure and mark installation spot for remaining
brackets. Use spirit level to mark vertical alignement.
Img. 4
5. Install remaining brackets to wall / ceiling.
Img. 5

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 11 / 19
6. Before installing the cassette open the brackets by
loosening the screw.
Img. 6
7. Slide the cassette to the brackets.
Img. 7
8. Lock the cassette in brackets by tightening the
screws.
Img. 8
9. Check horizontal level of the installed cassette.
Img. 9

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 12 / 19
10. Stretched chain has to be fixed to the wall by
adjusting the added safety element –on the height
150cm from the floor minimum. If necessary adjust
the chain length.
Img. 10
1. Check correct installation of brackets –their misplacement may cause danger for people.
2. After the installation check correct operation of the system.
5. SYSTEM OPERATION AND PRODUCT SAFETY
5.1. GENERAL SAFETY REQUIREMENTS
During product transport, assembly and disassembly, operation, care and maintenance, suitable regulations of
industrial safety and environmental protection should be observed,
The product should be maintained and repaired solely by the trained and suitably qualified personnel,
The Buyer should make sure that people assigned for carrying out activities connected with current use, cleanness
and maintenance of the product should be familiar with its operating manual and observe the guidelines in all
points of this manual,
Cleaning the product in a way different from the one described in the part entitled Technical inspections,
maintenance and repairs is forbidden,
All work must be carried out with due diligence taking into account safety requirements,
Markings on the product should be observed (e.g. icons, arrows denoting the direction of motion),
Make sure that markings are not covered with a layer of paint or damaged in a way making it impossible to read
them,
It is forbidden to introduce modification in the electrical design or in the equipment configuration without
consulting the manufacturer or an authorised representative,
Before the product is used, this manual should be read carefully,
The switch should be mounted at the height conforming to the national regulations concerning disabled persons,
not lower than 150cm at best.
5.2. SAFETY REQUIREMENTS CONNECTED WITH PARTICULAR CONDITIONS AND PLACES OF PRODUCT
USE
Particular safety requirements refer to children at the age of up to 42 months. Particular requirements for use apply to all
places accessible to little children or places where they spend time. Particular requirements for use apply also to all these
places where disabled persons spend time.
Prior to beginning to use the product, the Buyer must carry out individual risk assessment of its use
with particular attention paid to the safety of children and disabled persons.

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 13 / 19
While determining product operational requirements, it is essential to take into consideration rationally predictable
conditions of use and potential threats.
WARNING
- Young children can be strangled by loops in pull cords, chains, tapes and inner cords that operate
the product.
- To avoid strangulation and entanglement, keep cords out of the reach of young children. Cords
may become wrapped around a child’s neck.
- Move beds, cots and furniture away from window covering cords. Do not tie cords together. Make
sure cords do not twist and create a loop.
5.3. OPERATION SAFETY
Product can only be used when it is defect-free.
Product can be used only after installation and adjustment of added safety elements for chain.
Recommendations and actions:
the product is safe for use as long as the recommendations included in the documentation are observed,
all work connected with inspections and repairs of the product should be carried out by a properly trained person
holding adequate qualifications,
entering and staying in the up-down work area of the product should take place only when it is totally open and
stopped,
while folding and unfolding the product, attention should be paid that no objects or people are present within the
product work area (in the space between the guides and bottom bar),
no warm objects (e.g. irons, heaters etc.) shall be kept in proximity of the fabric,
safety elements for chain should be installed and adjusted in a secure way.
Forbidden actions:
Do not pull the product up by force. Doing so may result in system damage,
Stay clear of the work area of the blind while the system is working,
It is forbidden to use a product not conforming to the electric shock and fire safety requirements,
It is forbidden to exceed specific work parameters of the product determined in the technical and operational
documentation,
No sharp objects or protruding elements which can hook the bottom bar can be kept near the system,
it is forbidden to use faulty or incomplete product, using such product may result in its damage, pose threat to
user’s health and life,
It is forbidden to conduct self-repairs,
It is forbidden to use the product without relevant and required inspections and measurements,
It is forbidden to take off the drive casings,
Do not touch the movable elements while folding or unfolding the blind. It may result in crushing, cutting,
pulling in, or blocking between, e.g. the bottom bar and the other structural elements of the system,
Within the work space of a blind there should be no obstacles that might interrupt its work or damage it.
In case a blind enters an obstacle, first it should be folded slightly and then the obstacle should be
removed,
Stay clear of the work area of a blind while it is working,
It is forbidden to use the product without the installation of chain safety elements.
SELT Sp. z o. o. shall not be responsible for damage due to improper use.
Operating the system out of one’s sight can result in heavy injuries as well as system damage.
In case any irregularities in product operation are found, the Supplier should be informed immediately. Using a damaged
product and attempts to repair it on one’s own pose threat to health and life and may void the warranty.

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 14 / 19
5.4. SUPERVISION OF SAFE PRODUCT USE
The Buyer should:
a) in case safe product use depends on the conditions in which it is installed, submit the product to:
preliminary check (after it has been assembled and before handing it over to operation),
post-assembly check in another place,
b) make sure that the product exposed to conditions causing degradation of its technical condition, which may bring
about dangerous situations, is submitted to:
periodic checks and tests,
special check in case it is possible product safety should be worsened due to:
modification work,
natural phenomena,
prolonged downtime,
dangerous damage or accidents at work.
The above mentioned checks can be carried out by suitably qualified people.
6. SYSTEM USE AND MAINTENANCE
6.1. USING THE PRODUCT IN ACCORDANCE WITH ITS INTENDED USE
The system should be used in accordance with its intended use determined by the manufacturer. If the system is
used and modified in a manner different from the one described within this documentation, the system is used
incorrectly. Introducing arbitrary changes influencing safe operation of the product is not acceptable.
The following counts as proper product use:
regular or predictable use which does not include, e.g. risk undertaken deliberately or consciously by the user,
applying admissible values of work parameters,
observing recommendations for use,
carrying out periodic product inspections and maintenance,
following the requirements determined in the item ‘Supervision of Safe Product Use’,
data included in the item ‘Technical Specifications’,
using the product only with the correct installed chain safety elements.
In case of improper use:
the product can pose threat to its operators,
the product shall be exposed to damage,
it can be of negative influence on its functionality,
do not use the product in the course of maintenance work (e.g. window cleaning).
6.2. INSTRUCTIONS FOR NON-PROFESSIONALS
Prior to beginning to use the product this documentation should be carefully read.
Non-professionals shall denote people who are assigned by the Buyer to carry out activities connected with routine use,
cleanness and maintenance of the product.
Being familiar with this documentation guarantees fault-free operation of the product.
List of activities that can be carried out by non-professionals:
routine operation:
- carrying out activities which do not influence work parameters of the product,
product maintenance and cleanness described in the further part of this documentation,
control of chain safety element efficiency.

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 15 / 19
6.3. TECHNICAL INSPECTIONS, MAINTENANCE AND SERVICE
It is recommended to conduct periodic technical inspections of the product carried out by specialised service crews.
The inspections consist in checking product operation, mechanism adjustment, and exchange of wear parts. Routine
maintenance is carried out by the User themselves. Product maintenance should be performed at least once (1) a year by
specialised service crews.
The inspections are provided against payment.
Basic activities carried out during a periodic inspection:
Verification of:
product mounting to the structural elements,
technical condition of the movable elements of the product,
screw and rivet connections,
technical condition of the fabric,
mounting of the product drive mechanism (chain),
Possibly adjusting and improving the mounting of the changed sub-assembly.
Products manufactured by SELT Sp. z o. o. do not require special maintenance treatment. Using the product in
accordance with the manufacturer’s recommendations assures the user log-term and fault-free operation. Routine
maintenance activities should be carried out on a maximally opened system.
Basic product maintenance activities are:
checking if the roller blind unfolds and folds properly,
checking if the end switches work properly,
cleaning visible, accessible product elements.
Cleaning metal / aluminum elements:
It is recommended to clean slight dirt of metal / aluminum surfaces with the use of water with delicate cleaning
agents.
Forbidden activities during product maintenance:
It is not allowed to use a pressure washer, cleaning agents or solvents,
It is forbidden to use cleaning agents with the addition of chlorine, ammonia, kerosene, acetone, and
bleachers in order to clean the system, as well as in its proximity as it may cause the risk of corrosion,
It is forbidden to use sharp tools (e.g. wire brushes), scratching cleaning agents (e.g. scouring powders,
polish),
Do not hold or pull the system or its individual elements tight,
Do not replace individual elements! Spare parts should be original!

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 16 / 19
7. GENERAL WARRANTY CONDITIONS
General warranty conditions are available on www.selt.com. In case of no access to the SELT website, the warranty
conditions can be obtained from the sales representative of SELT Sp. z o. o.
7.1. EXCLUSIONS FOR WARRANTY
Warranty does not cover:
Damages resulting from transport other than SELT,
Damages resulting from storage, installation or maintenance activities other than described in the technical and
operational documentation or Supplier recommendations, unless those activities were conducted or advised by
the Supplier,
Damages resulting from failure to observe Supplier recommendations contained in the technical and operational
documentation of the product,
Mechanical damages,
Damages resulting from self-modifications conducted by the user, unless it was done by the Supplier, or on behalf
of the Supplier, or with its written permission,
Secondary damages resulting from using the product regardless of the noticed faults, unless the Supplier was
notified about it and recommended further use. The assessment of damage causes is left to the rational
recognition of the Supplier. Repair or change of the product due to the damages described herein can be done by
the Supplier against payment.
Faults resulting from normal wear of product parts, including: seals, lubricants, etc.,
Repairs involving regulation, cleaning and lubrication,
Damages resulting from incorrect installation of the product, self-repairs and adjustments,
Damages resulting from using the product in incorrect weather conditions,
Using the product regardless of damaged components.
Warranty for fabric does not cover:
Horizontal pressure marks arising due to the rod slipped into the fabric pocket and fixing the fabric in the roller
tube,
Asymmetrical rolling of the fabric on the roller tube due to not centering the fabric during installation,
Asymmetrical rolling of the fabric on the roller tube due to dirt on the fabric surface (e.g. leaves, mud etc.),
Elastic behaviour of the fabric when working in different temperature scope (connected with thermal expansion
of PVC),
„Waving” of the fabric resulting from roller tube bending,
„Vertical waves” on the fabric resulting from vertical tensions connected with shrinking in welding places,
Damages caused by abnormal weather conditions, lightning strikes,
Damages resulting from accidents and unexpected events (e.g. hurricane, tornado etc.),
Damages resulting from improper cleaning with the use of caustic and abrasive products and with improper tools,
Atmoshperic and phytosanitary pollution,
Effect of influence of other products or objects hanging on the fabric and not being delivered as a Selt system
part,
Differences in shade of fabrics, and in case of fabrics with metallisation –the grade of metalissation due to
different production batches,
„Memory effect of the fabric”: fabrics of bigger dimensions exceeding the width of the roll have to be done from
several cloths of the fabric, turned and welded. As a result the fabric in some cases rolls up on the sides. This is
due to the memory of the shape of the fabric tube. This effect can increase in high Releksol blinds and width
below 120 cm. The effect subsides along with the product use,
Gap in welding: in fabric wider than 430 cm (exceeding the width of the welding machine) it is necessary to make
a cut in the pocket. The cut is hidden in the bottom bar what makes it almost invisible and does not influence the
characteristics of the fabric. This is a technological norm,
Fabric welding: when the width and height of the blind exceeds the width of fabric roll, then it is necessary to
connect two fabric pieces by welding (fabrics are welded with heat and the visibility of welding is natural).
Weldings repeat horizontally with frequency depending on the width of fabric roll.

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 17 / 19
8. COMPLAINTS/ TECHNICAL FAULTS
8.1. COMPLAINTS (MANUFACTURER’S WARRANTY)
Complaints can only be made by the entity that purchased the product from the manufacturer.
The terms and way of handling complaints are defined in the General Guarantee Terms and Conditions as well as the
General Sales Terms and Conditions.
The General Guarantee Terms and Conditions and the General Sales Terms and Conditions are available on the website:
www.selt.com.
The Customer submits a complaint on the Complaint form available on the manufacturer's B2B platform. The complaint
notification should be full and complete.
A complaint submitted in a different way than via the B2B Platform, which is incomplete or partial, without given invoice
number, order number or contract number, will not be considered.
8.2. TECHNICAL FAULTS
In case product defects occur, one should:
fold the product and put it out of service,
immediately notify the dealer about the product fault.
notifications can be sent to the email address r[email protected] or directly to the sales representative
Complaints / faults should be made on the ‘complaint notification form’ which can be found on the website: www.selt.com,
or directly at the customer’s assistant.
9. PRODUCT DISASSEMBLY / UTILISATION / DISPOSAL
Improper system disassembly can result in severe injuries and system damage.
System disassembly should be commissioned to a properly qualified assembly team or to a person
suitably trained within industrial safety and with the knowledge concerning recovery.
a) Disposal of worn electrical and electronic equipment
After the end of product lifetime it must be disassembled and separate material must be segregated according to
Regulation of the Minister of Environment of 9 December 2014 on waste catalogue –Dz. U. [Journal of Laws] of 2014 item
1923
No.
Subject
European legal basis
Polish legal basis
1
Waste
catalogue
Commission Regulation (EC) No. 574/2004 of 23
February 2004 amending Annexes I and III to
Regulation (EC) No. 2150/2002 of the European
Parliament and of the Council on waste statistics.
Regulation of the Minister of Environment of
9 December 2014 on waste catalogue –Dz.
U. [Journal of Laws] of 2014 item 1923.

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 18 / 19
10. MARKING AND LABELLING THE PRODUCT WITH THE CE MARK
10.1. PRODUCT COMPLIANCE WITH THE CE STANDARD
Products manufactured by SELT company meet the essential requirements of the standard introduced by the Polish
Committee for Standardization as EN 13120.
In order to maintain this condition and assure safe use and maintenance of the system, the installation and operating
manual and instructions for safe use must be observed.
10.2. INFORMATION ACCOMPANYING THE CE MARKING
a) Marking on the product:
On the packaging there is a warning sticker with icon and text compliant with EN13120 (see point 11 of the
documentation).
On the packaging of safety elements added to the product and designed for installation of chain there are warnings: “Young
children can be strangled when the safety device is not installed and adjusted. Read carefully the instructions and install
accordingly.”
b) Marking on the accompanying documents:
In the documentation in point 11 there are placed warnings as described by the norm and drawing description of the
correct installation of devices tightening the chain.
Moreover, „Information on safety elements installation” is added to the product as a separate card.

DT-E 2.13: SUN PROTECTION SCREEN –REFLEKSOL 85 SA and 85 MA
Issue 2 / April 2017 / EN page 19 / 19
11. INFORMATION ON SAFETY ELEMENTS INSTALLATION
Young children can be strangled when the safety device is not installed and adjusted. Read carefully the
instructions and install accordingly.
Elements preventing strangulation available at SELT Sp. z o.o.
SLIM cord bracket
Chain security grip
Cord ending
INSTALLATION MANUAL
Endings of operation cords
were finished with PVC
elements (cord endings) to
prevent the cords from
twisting and creating a loop.
WARNING
- Young children can be strangled by loops in pull cords, chains, tapes and inner cords that operate
the product.
- To avoid strangulation and entanglement, keep cords out of the reach of young children. Cords
may become wrapped around a child’s neck.
- Move beds, cots and furniture away from window covering cords. Do not tie cords together.
Make sure cords do not twist and create a loop.