Sena WiFi Docking Station User manual

1 2
Sena WiFi Docking Station
Quick Start Guide
2.0.0
Main Unit Holder
microUSB
Connector
LED Indicators
microUSB Power Port
[WiFi Docking Station]
ENGLISH
2
[USB Power and Data Cable] [World Wide USB Wall Charger]
Notice:
Please use the USB Power and Data Cable and the World
Wide USB Wall Charger included in the package or a
compatible third-party microUSB cable (5V and higher than
1A) with the WiFi Docking Station. Do not connect the WiFi
Docking Station to a USB port on your PC.
LED Description
Charging Status
Firmware Upgrade Status
WiFi Status
3
Charging Status
Disconnected
Charging (Main unit is powered off)
Fully charged
Note:
Charging (Main unit is powered on).
To upgrade the rmware, power off the main unit.
Firmware Upgrade Status
Disconnected or no rmware upgrade available
Upgrading rmware
Firmware upgrade completed
WiFi Status
Disconnected from an WiFi access point
Searching for WiFi access point
Connected to an access point
4
Powering On
• Insert the USB Power and Data Cable into the microUSB
Power Port.
Attaching a Main Unit
Connect the main unit to the microUSB cable and attach it to the
WiFi Docking Station. Before connecting the main unit, power
off the unit.
Note:
If you leave the main unit on when connecting it, the charging
LED on the WiFi Docking Station will blink red slowly.
5
Connection Setup
1. Open the Sena Motorcycles App.
2. Tap the Menu button ( ) in the top-right corner of the
screen and select Update via WiFi.
3. Follow the instructions on the Sena Motorcycles App to
connect the WiFi Docking Station to a WiFi access point.
Note:
1. To change the WiFi access point, perform the Factory
Reset then repeat the steps above.
2. You can download the Sena Motorcycles App for Android
and Apple operating systems from www.sena.com.
Upgrading the Firmware of a Main Unit
The rmware will be upgraded automatically while your main
unit is charging. If you want to manually upgrade the rmware,
change the setting on the Sena Motorcycles App.
Note:
Do not unplug the USB Power and Data Cable from the WiFi
Docking Station while upgrading the rmware. The product
may be damaged.
5
SENA Technologies, Inc.
Customer Support: sena.com
Factory Reset
If you want to restore the WiFi Docking Station to the factory
default settings, you can easily reset the unit:
1. Locate the pinhole reset button on the unit.
2. Gently insert a paperclip into the hole and tap the Factory
Reset Button with light pressure.
3. The WiFi Docking Station will automatically restart with the
three LEDs on.
Note:
The WiFi Docking Station will be restored to factory default
settings which include the WiFi conguration setup, the
rmware setup and the language setup.
2.0.0_EN_September2022

1 2
Sena WiFi Docking Station
Quick Start Guide
2.0.0
Main Unit Holder
microUSB
Connector
LED Indicators
microUSB Power Port
[WiFi Docking Station]
ENGLISH
2
[USB Power and Data Cable] [World Wide USB Wall Charger]
Notice:
Please use the USB Power and Data Cable and the World
Wide USB Wall Charger included in the package or a
compatible third-party microUSB cable (5V and higher than
1A) with the WiFi Docking Station. Do not connect the WiFi
Docking Station to a USB port on your PC.
LED Description
Charging Status
Firmware Upgrade Status
WiFi Status
3
Charging Status
Disconnected
Charging (Main unit is powered off)
Fully charged
Note:
Charging (Main unit is powered on).
To upgrade the rmware, power off the main unit.
Firmware Upgrade Status
Disconnected or no rmware upgrade available
Upgrading rmware
Firmware upgrade completed
WiFi Status
Disconnected from an WiFi access point
Searching for WiFi access point
Connected to an access point
4
Powering On
• Insert the USB Power and Data Cable into the microUSB
Power Port.
Attaching a Main Unit
Connect the main unit to the microUSB cable and attach it to the
WiFi Docking Station. Before connecting the main unit, power
off the unit.
Note:
If you leave the main unit on when connecting it, the charging
LED on the WiFi Docking Station will blink red slowly.
5
Connection Setup
1. Open the Sena Motorcycles App.
2. Tap the Menu button ( ) in the top-right corner of the
screen and select Update via WiFi.
3. Follow the instructions on the Sena Motorcycles App to
connect the WiFi Docking Station to a WiFi access point.
Note:
1. To change the WiFi access point, perform the Factory
Reset then repeat the steps above.
2. You can download the Sena Motorcycles App for Android
and Apple operating systems from www.sena.com.
Upgrading the Firmware of a Main Unit
The rmware will be upgraded automatically while your main
unit is charging. If you want to manually upgrade the rmware,
change the setting on the Sena Motorcycles App.
Note:
Do not unplug the USB Power and Data Cable from the WiFi
Docking Station while upgrading the rmware. The product
may be damaged.
5
SENA Technologies, Inc.
Customer Support: sena.com
Factory Reset
If you want to restore the WiFi Docking Station to the factory
default settings, you can easily reset the unit:
1. Locate the pinhole reset button on the unit.
2. Gently insert a paperclip into the hole and tap the Factory
Reset Button with light pressure.
3. The WiFi Docking Station will automatically restart with the
three LEDs on.
Note:
The WiFi Docking Station will be restored to factory default
settings which include the WiFi conguration setup, the
rmware setup and the language setup.
2.0.0_EN_September2022

1 2
Sena WiFi Docking Station
Quick Start Guide
2.0.0
Main Unit Holder
microUSB
Connector
LED Indicators
microUSB Power Port
[WiFi Docking Station]
ENGLISH
2
[USB Power and Data Cable] [World Wide USB Wall Charger]
Notice:
Please use the USB Power and Data Cable and the World
Wide USB Wall Charger included in the package or a
compatible third-party microUSB cable (5V and higher than
1A) with the WiFi Docking Station. Do not connect the WiFi
Docking Station to a USB port on your PC.
LED Description
Charging Status
Firmware Upgrade Status
WiFi Status
3
Charging Status
Disconnected
Charging (Main unit is powered off)
Fully charged
Note:
Charging (Main unit is powered on).
To upgrade the rmware, power off the main unit.
Firmware Upgrade Status
Disconnected or no rmware upgrade available
Upgrading rmware
Firmware upgrade completed
WiFi Status
Disconnected from an WiFi access point
Searching for WiFi access point
Connected to an access point
4
Powering On
• Insert the USB Power and Data Cable into the microUSB
Power Port.
Attaching a Main Unit
Connect the main unit to the microUSB cable and attach it to the
WiFi Docking Station. Before connecting the main unit, power
off the unit.
Note:
If you leave the main unit on when connecting it, the charging
LED on the WiFi Docking Station will blink red slowly.
5
Connection Setup
1. Open the Sena Motorcycles App.
2. Tap the Menu button ( ) in the top-right corner of the
screen and select Update via WiFi.
3. Follow the instructions on the Sena Motorcycles App to
connect the WiFi Docking Station to a WiFi access point.
Note:
1. To change the WiFi access point, perform the Factory
Reset then repeat the steps above.
2. You can download the Sena Motorcycles App for Android
and Apple operating systems from www.sena.com.
Upgrading the Firmware of a Main Unit
The rmware will be upgraded automatically while your main
unit is charging. If you want to manually upgrade the rmware,
change the setting on the Sena Motorcycles App.
Note:
Do not unplug the USB Power and Data Cable from the WiFi
Docking Station while upgrading the rmware. The product
may be damaged.
5
SENA Technologies, Inc.
Customer Support: sena.com
Factory Reset
If you want to restore the WiFi Docking Station to the factory
default settings, you can easily reset the unit:
1. Locate the pinhole reset button on the unit.
2. Gently insert a paperclip into the hole and tap the Factory
Reset Button with light pressure.
3. The WiFi Docking Station will automatically restart with the
three LEDs on.
Note:
The WiFi Docking Station will be restored to factory default
settings which include the WiFi conguration setup, the
rmware setup and the language setup.
2.0.0_EN_September2022

1 2
Sena WiFi Docking Station
Quick Start Guide
2.0.0
Main Unit Holder
microUSB
Connector
LED Indicators
microUSB Power Port
[WiFi Docking Station]
ENGLISH
2
[USB Power and Data Cable] [World Wide USB Wall Charger]
Notice:
Please use the USB Power and Data Cable and the World
Wide USB Wall Charger included in the package or a
compatible third-party microUSB cable (5V and higher than
1A) with the WiFi Docking Station. Do not connect the WiFi
Docking Station to a USB port on your PC.
LED Description
Charging Status
Firmware Upgrade Status
WiFi Status
3
Charging Status
Disconnected
Charging (Main unit is powered off)
Fully charged
Note:
Charging (Main unit is powered on).
To upgrade the rmware, power off the main unit.
Firmware Upgrade Status
Disconnected or no rmware upgrade available
Upgrading rmware
Firmware upgrade completed
WiFi Status
Disconnected from an WiFi access point
Searching for WiFi access point
Connected to an access point
4
Powering On
• Insert the USB Power and Data Cable into the microUSB
Power Port.
Attaching a Main Unit
Connect the main unit to the microUSB cable and attach it to the
WiFi Docking Station. Before connecting the main unit, power
off the unit.
Note:
If you leave the main unit on when connecting it, the charging
LED on the WiFi Docking Station will blink red slowly.
5
Connection Setup
1. Open the Sena Motorcycles App.
2. Tap the Menu button ( ) in the top-right corner of the
screen and select Update via WiFi.
3. Follow the instructions on the Sena Motorcycles App to
connect the WiFi Docking Station to a WiFi access point.
Note:
1. To change the WiFi access point, perform the Factory
Reset then repeat the steps above.
2. You can download the Sena Motorcycles App for Android
and Apple operating systems from www.sena.com.
Upgrading the Firmware of a Main Unit
The rmware will be upgraded automatically while your main
unit is charging. If you want to manually upgrade the rmware,
change the setting on the Sena Motorcycles App.
Note:
Do not unplug the USB Power and Data Cable from the WiFi
Docking Station while upgrading the rmware. The product
may be damaged.
5
SENA Technologies, Inc.
Customer Support: sena.com
Factory Reset
If you want to restore the WiFi Docking Station to the factory
default settings, you can easily reset the unit:
1. Locate the pinhole reset button on the unit.
2. Gently insert a paperclip into the hole and tap the Factory
Reset Button with light pressure.
3. The WiFi Docking Station will automatically restart with the
three LEDs on.
Note:
The WiFi Docking Station will be restored to factory default
settings which include the WiFi conguration setup, the
rmware setup and the language setup.
2.0.0_EN_September2022

1 2
Sena WiFi Docking Station
Quick Start Guide
2.0.0
Main Unit Holder
microUSB
Connector
LED Indicators
microUSB Power Port
[WiFi Docking Station]
ENGLISH
2
[USB Power and Data Cable] [World Wide USB Wall Charger]
Notice:
Please use the USB Power and Data Cable and the World
Wide USB Wall Charger included in the package or a
compatible third-party microUSB cable (5V and higher than
1A) with the WiFi Docking Station. Do not connect the WiFi
Docking Station to a USB port on your PC.
LED Description
Charging Status
Firmware Upgrade Status
WiFi Status
3
Charging Status
Disconnected
Charging (Main unit is powered off)
Fully charged
Note:
Charging (Main unit is powered on).
To upgrade the rmware, power off the main unit.
Firmware Upgrade Status
Disconnected or no rmware upgrade available
Upgrading rmware
Firmware upgrade completed
WiFi Status
Disconnected from an WiFi access point
Searching for WiFi access point
Connected to an access point
4
Powering On
• Insert the USB Power and Data Cable into the microUSB
Power Port.
Attaching a Main Unit
Connect the main unit to the microUSB cable and attach it to the
WiFi Docking Station. Before connecting the main unit, power
off the unit.
Note:
If you leave the main unit on when connecting it, the charging
LED on the WiFi Docking Station will blink red slowly.
5
Connection Setup
1. Open the Sena Motorcycles App.
2. Tap the Menu button ( ) in the top-right corner of the
screen and select Update via WiFi.
3. Follow the instructions on the Sena Motorcycles App to
connect the WiFi Docking Station to a WiFi access point.
Note:
1. To change the WiFi access point, perform the Factory
Reset then repeat the steps above.
2. You can download the Sena Motorcycles App for Android
and Apple operating systems from www.sena.com.
Upgrading the Firmware of a Main Unit
The rmware will be upgraded automatically while your main
unit is charging. If you want to manually upgrade the rmware,
change the setting on the Sena Motorcycles App.
Note:
Do not unplug the USB Power and Data Cable from the WiFi
Docking Station while upgrading the rmware. The product
may be damaged.
5
SENA Technologies, Inc.
Customer Support: sena.com
Factory Reset
If you want to restore the WiFi Docking Station to the factory
default settings, you can easily reset the unit:
1. Locate the pinhole reset button on the unit.
2. Gently insert a paperclip into the hole and tap the Factory
Reset Button with light pressure.
3. The WiFi Docking Station will automatically restart with the
three LEDs on.
Note:
The WiFi Docking Station will be restored to factory default
settings which include the WiFi conguration setup, the
rmware setup and the language setup.
2.0.0_EN_September2022

1 2
Sena WiFi Docking Station
Quick Start Guide
2.0.0
Main Unit Holder
microUSB
Connector
LED Indicators
microUSB Power Port
[WiFi Docking Station]
ENGLISH
2
[USB Power and Data Cable] [World Wide USB Wall Charger]
Notice:
Please use the USB Power and Data Cable and the World
Wide USB Wall Charger included in the package or a
compatible third-party microUSB cable (5V and higher than
1A) with the WiFi Docking Station. Do not connect the WiFi
Docking Station to a USB port on your PC.
LED Description
Charging Status
Firmware Upgrade Status
WiFi Status
3
Charging Status
Disconnected
Charging (Main unit is powered off)
Fully charged
Note:
Charging (Main unit is powered on).
To upgrade the rmware, power off the main unit.
Firmware Upgrade Status
Disconnected or no rmware upgrade available
Upgrading rmware
Firmware upgrade completed
WiFi Status
Disconnected from an WiFi access point
Searching for WiFi access point
Connected to an access point
4
Powering On
• Insert the USB Power and Data Cable into the microUSB
Power Port.
Attaching a Main Unit
Connect the main unit to the microUSB cable and attach it to the
WiFi Docking Station. Before connecting the main unit, power
off the unit.
Note:
If you leave the main unit on when connecting it, the charging
LED on the WiFi Docking Station will blink red slowly.
5
Connection Setup
1. Open the Sena Motorcycles App.
2. Tap the Menu button ( ) in the top-right corner of the
screen and select Update via WiFi.
3. Follow the instructions on the Sena Motorcycles App to
connect the WiFi Docking Station to a WiFi access point.
Note:
1. To change the WiFi access point, perform the Factory
Reset then repeat the steps above.
2. You can download the Sena Motorcycles App for Android
and Apple operating systems from www.sena.com.
Upgrading the Firmware of a Main Unit
The rmware will be upgraded automatically while your main
unit is charging. If you want to manually upgrade the rmware,
change the setting on the Sena Motorcycles App.
Note:
Do not unplug the USB Power and Data Cable from the WiFi
Docking Station while upgrading the rmware. The product
may be damaged.
5
SENA Technologies, Inc.
Customer Support: sena.com
Factory Reset
If you want to restore the WiFi Docking Station to the factory
default settings, you can easily reset the unit:
1. Locate the pinhole reset button on the unit.
2. Gently insert a paperclip into the hole and tap the Factory
Reset Button with light pressure.
3. The WiFi Docking Station will automatically restart with the
three LEDs on.
Note:
The WiFi Docking Station will be restored to factory default
settings which include the WiFi conguration setup, the
rmware setup and the language setup.
2.0.0_EN_September2022