Senninger i-Wob UP3 User manual

PULL
PINCH
PINCH
Nozzle Removal
C
L
I
C
K
PLACE
PLACE
Nozzle Installation Nozzle Visibility
Whole sizes Half sizes
Notches
Made in the U.S.A.
Call [phone] • Web: www.senninger.com
®MS-1025
18 iWUP3-IN 02
If using The Magnum
Weight, always be sure the
weight is tightly threaded
into the bottom of the
i-Wob. 140 inch-lbs torque
recommended.
i-Wob®UP3®
Recommended installation
Component Assembly
BRACKET ASSEMBLY
Standard Angle 6-Groove
(Gray deector)
IWOB00B3SA6-UP3
Standard Angle 9-Groove
(Black deector)
IWOB00B3-UP3
Low Angle 9-Groove
(Blue deector)
IWOB00B3LA9-UP3
Low Angle 6-Groove
(White deector)
IWOB00B3LA-UP3
UP3 Nozzles
#6 - #26
UP3NZ06 - UP3NZ26
(Depending on deector)
UP3 Dual Nozzle Carrier
UP3NZCD
The Magnum Weight
(0.85 LB) MAGWGTBRB
(Includes i-Wob connector)

Made in the U.S.A.
Call [phone] • Web: www.senninger.com
®
System Design Criteria
To maintain
product warranty,
refer to the chart below
Standard Angle
6-Groove
(Gray)
Standard Angle
9-Groove
(Black)
Low Angle
9-Groove
(Blue)
Low Angle
6-Groove
(White)
Droplet Sizes
Small Droplets Medium Droplets Medium Droplets Large Droplets
Nozzle Sizes
Minimum #10 5/32" (3.97 mm) #6 3/32" (2.38 mm) #6 3/32" (2.38 mm) #12 3/16" (4.76 mm)
Maximum* #26 13/32" (10.32 mm) #26 13/32" (10.32 mm) #26 13/32" (10.32 mm) #26 13/32" (10.32 mm)
Flows
Minimum 2.24 gpm (509 L/hr) 0.80 gpm (182 L/hr) 0.80 gpm (182 L/hr) 3.24 gpm (736 L/hr)
Maximum 18.35 gpm (4168 L/hr) 18.35 gpm (4168 L/hr) 18.35 gpm (4168 L/hr) 18.35 gpm (4168 L/hr)
Maximum Spacing**
at 6 or 9 (1.8 or 2.74m)
ground clearance
18  (5.5 m) 20  (6.1 m) 18  (5.5 m) 15  (4.6 m)
Pressure at the Nozzle
Minimum 10 psi (0.69 bar) 10 psi (0.69 bar) 10 psi (0.69 bar) 10 psi (0.69 bar)
Maximum 15 psi (1.03 bar) 15 psi (1.03 bar) 15 psi (1.03 bar) 15 psi (1.03 bar)
* It is recommended that larger nozzle sizes be used only on soils that can handle higher application rates.
** For optimum performance Senninger recommends the use of maximum spacing for 1-2 spans only.
Note: Keep i-Wobs above crop canopy when outlet spacing exceeds 10  (3 m). This is especially important on high prole crops.
i-Wob System Assembly
Mounting
1. Always mount the i-Wob on a minimum of 2 
(0.6 m) reinforced exible hose. The hose must be
on the outlet end of any semi-rigid or rigid drop.*
2. Mount the i-Wob no less than 3  (0.91 m) above
the ground.
3. When using Senninger’s Magnum or One Weight,
always be sure it is tightly threaded to the bottom of
the i-Wob. (140 inch-lbs torque recommended)
4. If using a conventional drop weight above the i-Wob,
it should be a threaded weight of at least 1.5 lbs
(0.7 kg), and should not exceed 1  (0.38 m)
in length. A slip-over drop weight may cause
premature failure of the drop tube assembly. Never
combine weights above and below the i-Wob.
* If using Senninger’s thermoplastic goosenecks, a minimum
of 2  (0.6 m) of exible hose should be used on the outlet
end of any semi-rigid or rigid drop. In high canopy crops,
consider applicator height.
Pressure Regulator Location
1. Pressure regulators can be installed at the top of the
drop or near the applicator.
2. Follow your customized print out for proper
pressure regulator placement.
MS-1025
18 iWUP3-IN 02
Minimum ground
clearance:
3 . (0.91 m)
Rigid
Polyethylene
Minimum
2 . Flex Hose
Minimum
2 . Flex Hose