Senor iSPOS series Quick start guide

ENGINEERING NOTE 090514_HDD
POS to Perfection
Senor Tech Pty Ltd ABN:54093127765
65 Weaver Street, Coopers Plains, QLD, 4108 Australia
Telephone: [phone] Facsimile: [phone]
www.senortech.com.au [email protected].au
Purpose / Warnings
This document describes the Hard drive
Removal & Replacement procedure for the
ISPOS / KDS, series of Senor POS terminal.
Read this document before commencing, if anything is unclear contact Senor.
Ensure work area is clean
Follow normal anti-static practices.
Parts & Tools
No: 2 Medium Phillips Head screwdriver
No: 1.5 Medium Phillips Head screwdriver
Tweezers
Procedure
Ensure unit is powered off and disconnected from mains power
Disconnect all peripheral device data cables from the POS ports; take note of
their location for
Reinstall if needed.
Remove the rubber grommets to gain access to the Drive carrier retaining
screws as shown below

ENGINEERING NOTE 090514_HDD
POS to Perfection
Senor Tech Pty Ltd ABN:54093127765
65 Weaver Street, Coopers Plains, QLD, 4108 Australia
Telephone: [phone] Facsimile: [phone]
www.senortech.com.au [email protected].au
Using the no: 2 Medium Phillips Head screwdriver
Remove the Drive carrier retaining screws
As shown below

ENGINEERING NOTE 090514_HDD
POS to Perfection
Senor Tech Pty Ltd ABN:54093127765
65 Weaver Street, Coopers Plains, QLD, 4108 Australia
Telephone: [phone] Facsimile: [phone]
www.senortech.com.au [email protected].au
Using Thumb or Finger nail grip the Drive Carrier & gently slide
The Drive Carrier out of the terminal as shown below

ENGINEERING NOTE 090514_HDD
POS to Perfection
Senor Tech Pty Ltd ABN:54093127765
65 Weaver Street, Coopers Plains, QLD, 4108 Australia
Telephone: [phone] Facsimile: [phone]
www.senortech.com.au [email protected].au

ENGINEERING NOTE 090514_HDD
POS to Perfection
Senor Tech Pty Ltd ABN:54093127765
65 Weaver Street, Coopers Plains, QLD, 4108 Australia
Telephone: [phone] Facsimile: [phone]
www.senortech.com.au [email protected].au
Locate the phillips screw holding the Drive to the Carrier
Using the No:1.5 Medium Phillips Head screwdriver remove the carrier screws

ENGINEERING NOTE 090514_HDD
POS to Perfection
Senor Tech Pty Ltd ABN:54093127765
65 Weaver Street, Coopers Plains, QLD, 4108 Australia
Telephone: [phone] Facsimile: [phone]
www.senortech.com.au [email protected].au
The Drive carrier & Hard drive & screws & rubber grommets
Shown below
Fit the new Drive into the Drive carrier tighten the screws until the screw heads
are flush with the carrier, (this allows the drive to slide in the carrier’s slots)

ENGINEERING NOTE 090514_HDD
POS to Perfection
Senor Tech Pty Ltd ABN:54093127765
65 Weaver Street, Coopers Plains, QLD, 4108 Australia
Telephone: [phone] Facsimile: [phone]
www.senortech.com.au [email protected].au
Close The Unit
Reverse the dismantling procedure
Replace the rubber grommet and ensure the surface is flush with the plastic
carrier as shown below

ENGINEERING NOTE 090514_HDD
POS to Perfection
Senor Tech Pty Ltd ABN:54093127765
65 Weaver Street, Coopers Plains, QLD, 4108 Australia
Telephone: [phone] Facsimile: [phone]
www.senortech.com.au [email protected].au
Power Up
Double-check all connections for orientation and quality of connection
Connect only the mains power at first, turn on unit & power up
Ensure that unit boots into OS OK check for touch screen operation
Shut down & connect peripheral devices
Power up again, check system operation thoroughly