Senor iSPOS series User manual

iSPOS series
User’s Manual
(Rev.1.0)

iSPOS Series User’s manual
2
SAFETY STATEMENTS
Product Name : iSPOS
The following standards are applied only to the equipments that are
so labeled.
Europe : CE marking, VDE : EN 60950-1:2006
North America : EMI : FCC Class B
National : IEC 60950-1
CE Marking
The equipment conforms to the following Directive and Norms.
Directive : 2004/108/EC Directive: 2006/95/EC
ETSI EN 300 328 V1.7.1 : 2006
ETSI EN 301 489-17 V1.3.2 : 2008
EN 50371 : 2002
EN 60950-1 : 2006
Federal Communications Commission statement
This equipment has been tested and found to comply with the limits
for a class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from

iSPOS Series User’s manual
3
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This statement complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment.
This device complies with Part 15 FCC RF rules. Operation is
subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference
that may cause undesired operation of the device.
FCC RF Spec.
Interface Mini PCI
Network Standard IEEE802.11b/g
Modulation 802.11b----CCK (11Mbps. 5.5Mbps), QPSK (2Mbps), BPSK
802.11g----OFDM
Technique Direct Sequence Spread Spectrum
Operating Frequency
2.412 ~ 2.462 GHz: North America
2.412 ~ 2.472 GHz: Europe (ETSI)
Operating Channels 1 ~ 11 for North America
1 ~ 13 for Europe (ETSI)
RF Output Power 11b:18dBm +/- 1dBm(peak)
11g: 20dBm +/- 1dBm(peak)
Antenna Dipole antenna.
Supply Voltage 3.3V

iSPOS Series User’s manual
4
TRADEMARKS and ACKNOWLEDGEMENTS
All brand names and trademarks used in this manual are the properties and
registered brands of their respective owners
TABLE OF CONTENTS
SAFETY STATEMENTS ................................................................................................2
TRADEMARKS and ACKNOWLEDGEMENTS............................................................4
TABLE OF CONTENTS.................................................................................................4
1. SPECIFICATION........................................................................................................5
2. TERMINAL OVERVIEW AND OPERATION..............................................................8
2.1 LCD Angle Adjust..........................................................................................10
2.2 Touch Screen.................................................................................................10
2.3 Removable Hard Disk Drive .........................................................................11
2.4 Connectors....................................................................................................12
2.5 Power on........................................................................................................14
2.6 CF Card Installation and Removal...............................................................14
2.7 Wireless LAN Card Installation....................................................................15
2.8 Cash Drawer Board Installation...................................................................17
3. INSTALLATION .......................................................................................................18
3.1 Pre-installation ..............................................................................................18
3.2 Mounting........................................................................................................19
4. ROTATION DISK INSTALLATION...........................................................................22
5. REGULAR MAINTENANCE....................................................................................23
5.1 Cleaning.........................................................................................................23
5.2 Touch Screen.................................................................................................23
6. TROUBLESHOOTING.............................................................................................24
6.1 General Troubleshooting..............................................................................24
6.2 LCD Troubleshooting....................................................................................24
6.3 Disk Drive Troubleshooting .........................................................................25
6.4 RAM Troubleshooting...................................................................................25
6.5 Serial Port Troubleshooting.........................................................................25
6.6 Error Messages.............................................................................................26
CAUTION.....................................................................................................................27
PRECAUTION .............................................................................................................28

iSPOS Series User’s manual
5
1. SPECIFICATION
Overall Dimensions

iSPOS Series User’s manual
6
iSPOS
Weight: 8.5 Kg
EMC: CE、FCC Compliant、CCC
Safety: CE、VDE、CB、CCC
CPU: Micro-FCPGA AMD LX500 (iSPOS 150)
Intel Atom N270 1.6GHz, w/512KB Cache (iSPOS 650)
System Chipset:
AMD LX+CS5536 Chipset (iSPOS 150)
Intel 945GSE Chipset (iSPOS 650)
BIOS: Award BIOS, 2M Support ACPI Function (iSPOS 150)
Award BIOS, 4M Support ACPI Function (iSPOS 650)
Standard I/O: 1 × PS/2 Port (Keyboard)
4 × USB 2.0 Port (3 External USB 2.0 Port, 1 Internal USB 2.0 Port)
1 × Mini Printer Port (iSPOS 150 / iSPOS 650 P)
1 × VGA Port (iSPOS 650 V)
1 × LAN Port
1 × Audio Port
1 × MIC Port
1 x Compact Flash type II socket for CF card
4 × RJ-48 Com Port (COM3 ~ 6)
System
Memory: Two SODIMM DDR2 socket/ 1GB up to 2GB DDR2 533
Ethernet: REALTEK RTL8111C (10/100/1000)
Ethernet Controller Supports wake up-on-LAN function

iSPOS Series User’s manual
7
VGA: Microsoft Windows GDI GUI Acceleration.
Audio Interface:
Codec ALC662
USB Interface: Intel 945 GSE Support 4 Port
Hard Disk Drive:
SATA: 1 x socket for HDD / 1 x Compact Flash Socket
Operator Display:
Size 15” (diagonal)
Active Area 304.1 mm (H) x 228.1 mm (V)
Resolution 1024 (H) x 768 (V) x R,G,B
Display Mode Normally White
Contrast Ratio 500:1 type.
Luminance 250 cd/m² type / 350 cd/m².
Touch Screen:
Technology 5 Wire analogue resistive
Chemically strengthened backing glass.
Resolution 4096 x 4096 points
Activation Force
5.5g
Linearity 62.0%
Transparency 75%
Surface
Hardness 2H
Interface RS-232 Serial
MTBF 1,000,000 touches / spot
Power Supply:
Input Voltage 100 ~ 240Vac
Input Frequency 47 ~ 63Hz
Input Current 100-240Vac 1.5A
Output Voltage +12Vdc 5A
Operating
temperature 0°C to 40°C
Size 120mm(L) x 60mm(W) x 38mm(H)
Enclosure Water & Dust Protection (IP Rating): IP66
Note: Specifications are subject to change without notice.

iSPOS Series User’s manual
8
2. TERMINAL OVERVIEW AND OPERATION
iSPOS is licensed IP66 water and dust proof certification, and it is
specially developed to satisfy the needs of reliable systems in harsh
environments, safety, ergonomics, and work efficiency for the retail and
hospitality or any industrial applications. It is designed for your best
convenience and comfort, and its aluminum casing, sub nano technology
coating and ventless features help you to clean it easily.
Features :
 IP66, Water and Dust
Proof
 Ventless Design
 Robust Aluminum
Casing
 Ergonomic Design
 VESA Mount standard  Fanless Design
 Removable Hard Disk  Peripheral / Customer
Display (Option)
 Sub Nano Coating  Wireless LAN

iSPOS Series User’s manual
9
iSPOS
VFD
(Option)
(Option)
Reader Removable
Hard Disk Drive
Push ON Switch
Foot(5x)
Indicator
EXT USB
VFD Interface Cover
Card Reader
Interface Cover
HDD Cover
Antenna
Overview – iSPOS

iSPOS Series User’s manual
10
2.1 LCD Angle Adjust
1. In order to accommodate various operating preferences and lighting
conditions. iSPOS is equipped with a manual tilt adjustment mechanism.
The Adjustment button is located underneath the display. Refer to
diagram (1).
2. To adjust the tilt angle, press adjustment button as indicate direction.
press and fix the button in enables tilt adjustment. The tilt movement is
limited to a minimum of 34 degree and a maximum to 70 degrees. Refer
to Diagram (2)
3. After tilt angle has been adjusted, press the button again to release the
button. When adjustment button released the LCD angle is locked.
2.2 Touch Screen
Touch screen uses 5 wire analog resistive technology, mounted on a
chemically strengthened back glass, with a resolution of 4096 x 4096
touch points. iSPOS is designed so that the application accepts all user
input via the touch screen. Drivers are provided which allow the touch
screen to emulate mouse operation; therefore most mouse driven
applications will accept input from the touch screen.
Diagram (1) Diagram (2) Diagram (3)

iSPOS Series User’s manual
11
Waterproof plug(2x)
Screw(2x)
HDD Cover
HDD
2.3 Removable Hard Disk Drive
Removable hard disk is located left side of panel. Following drawings
illustrate removal procedure.
Caution:
A. The HDD must be fitted with HDD cover.
B. Do Not insert the HDD into the iSPOS without the HDD Cover installed
or damage to the HDD and/or the iSPOS will occur.
C. The iSPOS power must be switched off before inserting or removing
the HDD

iSPOS Series User’s manual
12
COM 6
COM 5 COM 3
COM 4
PS2 K/B
USB(2x)
LAN PRINTER or VGA
AC POWER
AUDIO
MIC
Fastener(2x)
PRINTER or VGA
PS2 K/B
LAN
AUDIO
COM 3
COM 4
COM 5
COM 6
USB
USB
MIC
2.4 Connectors
Bottom View – I/O Connector Location
Chassis Inner View

iSPOS Series User’s manual
13
Fixing panel
COM 6
COM 5
COM 4
COM 3
Audio
MIC
PRINTER or VGA
USB(2X)
PS2 K/B
LAN
DC Power
USB CF Card
Sillica gel plug
Sillica gel grommet
Velcro(2x)
Cable
Power Adapter Cover
Connector locations
Power Supply Enclosure

iSPOS Series User’s manual
14
RED ------ AC Input OK
Blue ------ Booting Mode
2.5 Power on
Turn on the unit by pressing “Push ON Switch” located under the Logo on
the front of LCD, turn off the unit manually by pressing and holding the
switch for 3 seconds. When connected to an AC source, the Power Mode
LED will illuminate automatically. The unit’s mode can be determined by
the Power Mode LED color.
2.6 CF Card Installation and Removal
2.6.1 Insert CF card as diagram (1).
Diagram (1) : CF card installation

iSPOS Series User’s manual
15
2.6.2 Remove the CF card by pressing black button as indicated.
2.7 Wireless LAN Card Installation
2.7.1. Insert wireless LAN card into the unit.

iSPOS Series User’s manual
16
2.7.2 Remove Antenna Cover from chassis.
2.7.3 Install the Water Sealing Washer and Antenna. Connect the Antenna
Connector to Wireless LAN card.

iSPOS Series User’s manual
17
2.8 Cash Drawer Board Installation
Install Cash drawer board as shown in diagram (2). Attach plastic
standoffs followed by the plastic screws.
plastic screw
plastic boss
plastic screw
Diagram (2) : Cash drawer board installation.

iSPOS Series User’s manual
18
3. INSTALLATION
It is important that before installation the iSPOS terminal's position and
environment be considered.
3.1 Pre-installation
Location: Ensure that as with any computer equipment, iSPOS terminal is
positioned in a clean and well-ventilated area away from direct sunlight
Operator’s Comfort and Safety: Operator comfort and safety should always
be of the highest priority when deciding on the location and layout of the
iSPOS system. Please note comfortable distance between operator and
touch screen; the operator should not have to stretch to reach the screen
but also should not be in a cramped position. The height of the terminal
should be which the operator can view the screen at right angles.
Clearances: iSPOS terminal should be located where there is adequate
clearance for ventilation around the terminal. Similarly, clearance around
the power supply for ventilation, as well as access to the power switch,
indicators and connectors should be allowed for. Additional consideration
should be given to ensure nothing can be placed over the fan or vent holes,
e.g. paper, rags etc.
Cable Routing: In most cases position of printers, scanners, etc. will
sometimes be necessary that cable will have to be run through counter
dividing panels and shelves. Try to keep these cables run as short as
possible, while avoiding stretching or crimping the cable. Keep iSPOS
data cables separated from other equipments, in particular motors, lighting,
refrigeration etc.
Mains AC Power Supply: AC supply for iSPOS system should be a
dedicated feed from the main power switch. Do not connect any other
equipment to this feed or damage to the iSPOS terminal or its peripherals
may result. A suggestion is to clearly identify each iSPOS terminal power
outlet as a dedicated point. The supply should have a reliable ground at
the switchboard.
Configuration: Number of methods can be used to install iSPOS,
dependant on countertop configuration, user preference and peripherals
connected. It can simply sit on the countertop, in which case care must be
taken to ensure it cannot be knocked off the countertop when bumped. It
can also be fixed to the countertop using the provided base unit or

iSPOS Series User’s manual
19
Waterproof plug(2x)
Screw(2x)
mounted on vesa bracket or arm. It would be impossible to cover every
installation situation in this manual so each should be considered
individually .
3.2 Mounting
iSPOS is designed to be fitted with a base unit or with a VESA standard
mounting bracket or arm (75 mm X 75 mm; 100 mm X 100 mm) if required.
Unscrew the two screws securing the base unit to the LCD panel.
Separate the LCD Panel from the base unit by lifting the LCD panel.
Use four M4 screws to secure iSPOS LCD panel onto any VESA standard
mounting bracket or arm.

iSPOS Series User’s manual
20
Mounting on the ceiling
The cable assembling
sequence as follows.
1. DC IN cable x 1
2. SCSI Printer cable x 1
3. RS232 x 4
4. LAN x 1
5. PS2/KB x 1
6. USB cable x 2
7. Audio cable x 1
8. Microphone cable x 1
Cable exit (UP)
Cable exit (Side)