SENSECAP S210X Safety guide
THE NEW GENERATION L ORAWAN SENSORS OF SENSECAP
How to Connect S210X Sensors to
Helium Network
Version: v1.0.0
Table of Contents
1. Connect to Helium Network........................................................................1
1.1Helium Console.......................................................................................................1
1.2Connect to Helium Network.....................................................................................2
1.2.1 Create a New account................................................................................................. 2
1.2.2 Setup the Sensor......................................................................................................... 2
1.2.3 Set Frequency of Sensor via SenseCAP Mate App.................................................... 3
2. Helium Console Configuration...................................................................5
2.1Add New Device......................................................................................................5
2.2Check the data on Helium .......................................................................................6
2.3Upload Data from Helium to Datacake.....................................................................7
2.3.1 Create a Datacake Account ........................................................................................ 7
2.3.2 Add New Integration on Helium Console .................................................................... 8
2.3.3 Configure the Flows on Helium................................................................................... 9
2.3.4 Add the Sensor on Datacake .................................................................................... 11
2.3.5 Check Data from Datacake....................................................................................... 13
3. Trouble Shooting.......................................................................................16
3.1Support..................................................................................................................16
3.2Document Version.................................................................................................16
IoT into the Wild
1
1. Connect to Helium Network
1.1 Helium Console
The Helium Console is a web-based device management tool hosted by the Helium
Foundation that allows developers to register, authenticate, and manage their
devices on the Helium network. In addition to device management, Console provides
prebuilt connections called Integrations to route device data via HTTPs or MQTT; or
directly to cloud services like AWS IoT.
IoT into the Wild
2
1.2 Connect to Helium Network
1.2.1 Create a New account
Please go to https://console.helium.com/ , and register your account.
1.2.2 Setup the Sensor
1) Open the SenseCAP Mate App
2) Press button and hold for 3 seconds, the LEDwill flash at 1s frequency.
3) Please click the “Setup” button to turn on Bluetooth and click “Scan”to start
scanning the sensor's Bluetooth.
4) Select the Sensor by S/N (label). Then, the basic information of the sensor will be
displayed after entering.
IoT into the Wild
3
1.2.3 Set Frequency of Sensor via SenseCAP Mate App
Set the corresponding frequency band based on the frequency band of the gateway.
1) Click the “Setting” and select the platform is “Helium”.
2) Select the Frequency Plan, if the gateway is US915, set the sensor to US915.
IoT into the Wild
4
3) Click the “Send” button, send the setting to the sensor for it to take effect.
4) Click the “Home” button, the App will disconnect the Bluetooth connection.
Then, the sensor will reboot.
5) When the device is disconnected from Bluetooth, the LED lights up for 15
seconds and then flashes as a breathing light.
6) Afterjoining the network successfully, LED flashes fast for 2s.
IoT into the Wild
5
2. Helium Console Configuration
2.1 Add New Device
1) Click “Devices” –> “Add New Device”
2) Enter the Device EUI, App EUI, App Key: please refer to SenseCAP mate APP
for details.
3) Save device.
4）Add a new label, then add the label to a device.
IoT into the Wild
6
2.2 Check the data on Helium
1) Enter device detailspage and find the REAL TIME PACKETS.
IoT into the Wild
8
2) Click the “Edit Profile” →“API” →Get API token.
2.3.2 Add New Integration on Helium Console
1) Click “Integrations” →”Add New Integration” →”Datacake”.
IoT into the Wild
10
2) Drag the Label into a blank place.
3) Drag the Integration in to a blank place.
4) Connect the two blocks.
IoT into the Wild
11
5) Save Changes.
2.3.4 Add the Sensor on Datacake
1) Return Datacake Dashboard, and click “Device”→”Add Device”
2) Choose “LoRaWAN”.
IoT into the Wild
12
3) Search “Seeed” and select the Sensor Template.
4) Select “Helium”.
IoT into the Wild
13
5) Enter your Device EUI and Name.
6) Select your Plan and add device.
2.3.5 Check Data from Datacake
1) Click Debug button, it will display debug log.
IoT into the Wild
14
IoT into the Wild
15
IoT into the Wild
16
3. Trouble Shooting
3.1 Support
Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different
time zones, we cannot offer live support. However, your questions will be answered
as soon as possible in the before-mentioned schedule.
Provide as much information as possible regarding your enquiry (product models,
accurately describe your problem and steps to replicate it etc.) and send a mail to:
sensecap@seeed.cc
3.2 Document Version
Version
Date
Description
Editor
V1.0.0
7/29/2022
First edition
Kelvin Lee
V1.0.1
8/30/2022
Modify some descriptions
Andrea
Other manuals for S210X
1
Table of contents
Other SENSECAP Accessories manuals
