Sensio Torino User manual

Sensio House, Unit 7, Speedwell Road, Whitwood, Castleford, West Yorkshire, WF10 5PY
www.sensio.co.uk
Technical drawings for illustraon purposes only, Sensio has the right to change any informaon without
prior noce.
PRK0010 V1
Waste Electrical & Electronic Equipment (WEEE)
The symbol on the product, or on the document accompanying the product, the crossed out wheelie
bin symbol, indicates that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collecon point for the recycling of electrical and
electronic waste.
5. Suitable for furniture lighng.
6. When the lamp expires the fing must be replaced
7. Class III safety extra low voltage (SELV).
1. Before commencing installaon or maintenance, isolate the main
electrical supply for the appropriate circuit at the fuse board.
2. This product is only suitable for connecng to a 240V 50Hz supply.
3. The lights should be mounted onto a secure surface.
4. Never exceed the total output of the LED driver.
Safety Instrucons
Product Code
SE17232C0
SE17238C0
SE17262C0
SE17268C0
Model
600 x 200 x 20 (Silver)
600 x 200 x 20 (Black)
900 x 200 x 20 (Silver)
r
900 x 200 x 20 (Black)
Waage
5.4W
5.4W
8.4W
8.4W
Please read these instrucons carefully before aempng to install this
product. It is advisable to keep these instrucons in a safe place for future
reference.
We recommend that you consult a qualified electrician. All
electrical installaon must be carried out in accordance with
current IEE wiring regulaons (BS7671).
These pThese products must not be modified, if any modificaon are made, it may
invalidate the warranty and may render the product unsafe. These LED
lights operate low voltage (24V).
Do not wire the individual LED light fings directly to the mains. This prod-
uct is for indoor use only. Keep out of moisture and use only in dry rooms.
• If in doubt, installaon must be carried out by a qualified
electrician.
• Install on smooth flat surface(s) only.
• Do not exeed or stretch the cable length of each LED wire.
• This product is IP20 Rated.
• The waage for each shelf is listed in the table below. Make sure
th that the LED driver used with the shelf has an appropriate max
waage, which is higher than the product waage.
Important Safety Informaon
Pencil Screwdriver Ø6 mm
Drill Bit
Power Drill
Rawl Plugs & Screws
4 of each for 900mm wide shelves
3 of each for 600mm wide shelves
2 x
End-Caps
Shelf Frame Wall Bracket Glass Pane 1 x Instrucons
Manual
Tools Required
Components
IMPORTANT: Please read these instrucons before commencing installaon and retain for future reference.
INSTALLATION
INSTRUCTIONS

Maintenance & Care
• Ensure that the power is disconnected prior to cleaning.
• To keep the finish of this product, wipe over with so cloth periodically.
• Do not use harsh chemical solvents, this may dis-colour or damage the finish.
• Do not over-ghten screws on the terminal block.
Technical drawings for illustraon purposes only, Sensio has the right to change any informaon
without prior noce.
www.sensio.co.uk
Sensio House, Unit 7, Speedwell Road, Whitwood, Castleford, West Yorkshire, WF10 5PY
Product Overview
The Torino is a sleek and stylish LED shelf that has cool
white LED’s embedded within the frame to create a
stunning glow as the light is refracted through the
tempered glass.
The shelf is designed The shelf is designed for easy installaon, so once the
wall bracket is secured to the wall the shelf simply slots
into it.
The Torino is available in two colours, which are
anodized aluminium and ma black. The product is also
available in 600 or 900mm lengths.
The The Torino has a high IP rang (IP44) making the shelf
suitable for installaon in bathroom zone 2. It also has a
recommended maximum load of 8kg, making it suitable
to display a multude of objects and decoraons.
Operaon
Insert the two end caps and the pane of glass. Finally,
connect the driver to the mains supply, or aach a plug.
5
Insert the hook on the shelf into the groove of the wall bracket.
Note: Be careful to thread the cable through the cable channel and into the Ø8mm hole. Once the cable is threaded,
connect it to the driver.
Cable Channel
4
Insert the Rawl plugs into the wall and then screw the
bracket into posion.
3
6.00
Aer drilling the screw holes, you will need to carefully
mark an addional hole for the cable using the
dimensions shown above. Proceed to drill the hole once
complete.
2
900mm Shelf - X = 40mm
600mm Shelf - X = 40mm
Carefully mark the desired locaons for the screw holes
using the dimension shown above and proceed to drill
the holes.
Note: You will need to use a Ø8mm drill bit.
Y
900mm Shelf - X = 275mm - Y = 270mm
600mm Shelf - X = 260mm - Y = N/A Only 3 screw holes
1
Installaon
Torino - LED Wall Mounted Shelf
PRK0010 V1