Whittier Wood Furniture McKenzie 1375AFGAC User manual

1375AFGAC; 1375AFCAF
AFGAC = Glazed Antique Cherry finish
AFCAF = Caffè finish
Production Code:
06/10
VN
Model #
Assembly Instructions
P.O. Box 2827
Eugene, OR 97402 USA
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions before you begin your project.
McKenzie Bookcase
King Storage Bed
Before you load or move this unit, check to make
sure all screws and supports are tight.
This assembly requires two people.
.
Before you begin your project, completely read the
Assembly Instructions.
For normal household use only. Not recommended
for commercial use.
Unload items before you move this unit.
Do not overload the concealed storage areas.
Do not overload the drawers.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40°F to 90°F (not on a
cold and possibly damp cement floor).
Periodically inspect your furniture for any loose
glue joints, screws or any other problem that might
affect the stability of your furniture. Tighten or
repair as needed.
IMPORTANT NOTES:
Service Policy: We will replace any part that is
defective, missing or damaged during assembly.
Please contact Whittier Wood Products customer
service department directly by phone, fax, mail or
email for a replacement part.
To Order: Designate the finish, provide the furniture model
number (upper part of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one
or two business days from the time we receive your
request. Please allow five to ten business days for delivery.
CALL US FIRST! Do not return this item to the store.
800-653-3336 • Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Hours: Our friendly customer service staff can be
reached Monday-Friday 7:00 a.m. to 5:00 p.m.
(Pacific Time). You may leave a message 24 hours
a day, seven days a week.

1375AFGAC; 1375AFCAF McKenzie Bookcase
King Storage Bed — Parts List
1377AFGAC; 1377AFCAF Headboard Kit (x1)
Page 2 — 1375AFGAC_1375CAF — 06/10
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and model name.
Y — #8x7/8" LoProfile Screw
— Qty. 4 (inserted)
ZE — Door Stay
— Qty. 2 (attached)
ZG — Door Stay Support
— Qty. 2 (attached)
ZF — #6x5/8" Undercut
Screw — Qty. 8 (inserted)
ZA — Hinge
— Qty. 6 (installed)
ZC — Magnetic Catch
— Qty. 4 (installed)
ZJ — #6x5/8" Philtruss
Screw — Qty. 8 (inserted)
ZB — Magnetic Plate
— Qty. 4 (installed)
X — Power Strip
— Qty. 1 (installed)
ZI — #6x5/8" Flat Head
Screw — Qty. 36 (inserted)
ZD — #5x5/8" Flat Head
Screw — Qty. 8 (inserted)
ZH — #6 x 1-1/4" Black Pan
Head Screw — Qty. 6 (inserted)
ZN — #8 x 1-1/4" Pan Head
Screw — Qty. 17 (inserted)
E — #8 x 1-1/4" Black
Screw — Qty. 59 (inserted)
ZO — #8 x 2-1/4" Black
Screw — Qty. 6 (inserted)
ZP — #8 x 1" Black
Screw — Qty. 16 (inserted)
ZQ — Left Bracket
— Qty. 2 (attached)
ZR — Right Bracket
— Qty. 2 (attached)
A — Headboard Assembly
— Qty.1
R — Assembled Door
— Qty. 2 (attached)
S — False Bottom
— Qty. 4
YB — #8 x 5/8" Pan Head
Screw — Qty. 8 (inserted)
ZS — Wire Clip
Screw — Qty. 8 (attached)
ZT — Tack Glide
— Qty. 4 (attached)
ZZ — Corner Brace
— Qty. 2 (attached)
YA — Large Adjustable Glide
— Qty. 2 (installed)

1375AFGAC; 1375AFCAF McKenzie
Bookcase King Storage Bed — Parts List continued
Page 3 — 1375AFGAC_1375AFCAF— 06/10
1378AFGAC; 1378AFCAF Footboard Kit (x1)
F — 1/4" x 1-3/4" Hex Bolt
— Qty. 16
G — 1/4" x 2-1/2" Hex Bolt
— Qty. 16
E — #8 x 1-1/4" Black Screw
— Qty. 48 (12 inserted)
H — Washer
— Qty. 32
B — Footboard — Qty.1
C — Trestle Without T-Nuts
— Qty.4
D — Trestle With T-Nuts
— Qty.8
T — #8 x 2" Black Screw
— Qty. 6
U — Foot Assembly
— Qty. 2
V — Leveler Bracket
— Qty. 2 (installed)
W — Adjustable Glide
— Qty. 2 (installed)
1318AFGACa; 1318AFCAFa Pedestal Kit (x2)
N — #8 x 1-1/2" Machine Screw
— Qty. 3
O — Knob — Qty. 3
I — Pedestal Kit — Qty.1
P — Deckboard — Qty.1
ZM — Center Deckboard — Qty.1
L — Small Drawer Face
— Qty. 2 (attached)
M — Large Drawer Face
— Qty. 1 (attached)
Q — Drawer Slides — Qty. 3
(attached sets)
T — #8 x 2" Black Screw
— Qty. 16 (inserted)
ZQ — Left Bracket
— Qty. 2 (attached)
ZR — Right Bracket
— Qty. 2 (attached)
ZP — #8 x 1" Black Screw
— Qty. 16 (inserted)
ZW — #6 x 1/2" Undercut
Screw — Qty. 30 (inserted)
Y — #8 x 7/8" Lo-Profile
Screw — Qty. 20 (inserted)
E — #8 x 1-1/4" Black Screw
— Qty. 30 (inserted)
ZX — #8 x 1-5/8" Black
Screw — Qty. 12 (inserted)
ZP — #8 x 1" Black
Screw — Qty. 16 (inserted)
ZU — T-Nut
— Qty. 32 (inserted)
ZQ — Left Bracket
— Qty. 2 (attached)
ZR — Right Bracket
— Qty. 2 (attached)
ZV — #8 x 20mm Pan Head
Screw — Qty. 30 (inserted)
ZY — Foot Bracket
— Qty. 2 (attached)
J — Small Drawer Box
— Qty. 2 (assembled)
K — Large Drawer Box
— Qty. 1 (assembled)

1375AFGAC; 1375AFCAF McKenzie
Bookcase King Storage Bed
Assembly Instructions
Page 4 — 1375AFGAC_1375AFCAF — 06/10
Tools required: Phillips screwdriver, Slotted screwdriver, 7/16" wrench, Tape measure
This assembly requires two people
Remove the Trestles (C/D) and Foot Assemblies (U) from the back of the Footboard (B) and
place them off to the side. See Figure 1.
1.
Place both Pedestals (I) approximately 79" apart as shown in Figure 2.2.
Fig. 1
Fig. 2
I
I
79"
C/D
U
U
B
Shipping Straps

Page 5 — 1375AFGAC_1375AFCAF —06/10
Remove the Drawers (J & K) from the Pedestal Kits (I). To remove the drawers, pull up on
the left side of the Drawer Release Lever while pushing down on the right Drawer Release Lever.
See Figure 3a. Note where each drawer came from to ensure correct installation.
Positions are marked on the drawer bottoms.
3.
Fig. 3
Fig. 3a
Drawer Release Lever
Place four Trestles with T-Nuts (D) between the Pedestals (I) and insert and hand-tighten
1/4 x 1-3/4" Bolts (F) and Washers (H) as shown in Figure 4a. When installing the Trestles (D),
make sure the T-nuts face out as shown in Figure 4.
NOTE: Do not tighten the bolts with a wrench until the final assembly in
step 10 is completed. Hand-tighten only.
4.
Fig. 4a
Trestle with T-Nuts (D)
F x 16 H x 16
H
F
Fig. 4
T-Nuts face out
D
D
D
D
I
I

Page 6 — 1375AFGAC_1375AFCAF — 06/10
5. Rotate the Pedestal Assembly upside down so the plywood deckboards are on the floor.
Fig. 6a
G x 16 H x 16
Fig. 6
D
D
D
D
C
CC
C
6. Position the remaining Trestles (C and D) on the Pedestal Assembly. Face the Trestles with
T-Nuts (D) toward the ends of the Assembly from the center as shown in Figure 6. Insert and
hand-tighten the 1/4" x 2-1/2" Hex Bolts (G) and Washers (H). See Figures 6 and 6a.
Fig. 5
R
o
t
a
t
e
P
e
d
e
s
t
a
l
A
s
s
e
m
b
l
y
u
p
s
i
d
e
d
o
w
n
s
o
t
h
a
t
t
h
e
p
l
y
w
o
o
d
D
e
c
k
b
o
a
r
d
s
a
r
e
o
n
t
h
e
f
l
o
o
r
.
NOTE: Do not tighten the bolts with a wrench until the final assembly in
step 10 is completed. Hand-tighten only.
G
H

Page 7 — 1375AFGAC_1375AFCAF— 06/10
Rotate the Pedestal Assembly to its original position.
Fig. 7
Fig. 7a
D
D
CC
T x 6
7.
8.
On one inner pair of Trestles (C & D), place a Foot Assembly (U) between the Trestles as
shown in Figure 7. Attach with three #8 x 2" Black Screws (T). Repeat the step for the
second Foot Assembly. See Figures 7 and 7a.
U
Fig. 8
R
o
t
a
t
e
P
e
d
e
s
t
a
l
A
s
s
e
m
b
l
y
t
o
i
t
s
o
r
i
g
i
n
a
l
p
o
s
i
t
i
o
n
.
V
W
T

Page 8 — 1375AFGAC_1375AFCAF — 06/10
Attach the Headboard (A) to the Pedestal Assembly as in the previous step.
NOTE: Now use a wrench and tighten all of the bolts on the trestles.
10.
Attach the Footboard (B) to the Pedestal Assembly as in Figure 9. Align the brackets as shown
in Figure 9a and slide the Pedestal Assembly down on to the Footboard (B).
9.
Fig. 9a
Fig. 9
B
Fig. 10
A

Page 9 — 1375AFGAC_1375AFCAF — 06/10
Place your bed in its final position. To level the headboard, stand in the open area in between
the two attached deckboards and reach through the front of the platform. See Figure 11. Using
a slotted screwdriver, rotate the Large Adjustable Glide (YA) clockwise until it bears weight.
Repeat for the opposite side. See Figures 11a and 11b.
THIS IS ESPECIALLY IMPORTANT IF THE BOOKCASE HEADBOARD SITS UPON A CARPET
TACK STRIP.
11.
Fig. 11
Adjust the Glides (W) on the Foot Assemblies (U) so the Glides just touch the floor.12.
Fig. 11a
Adjustable Glide (W)
Leveler Bracket (V)
YA
ZZ
The top of the Large Adjustable
Glide (YA) is slotted.
Foot Assembly (U)
Fig. 11b
Fig. 12

Page 10 — 1375AFGAC_1375AFCAF — 06/10
Place the Deckboards (P) as shown in Figure 14. There should be a small gap between each
deckboard. Secure with 24 #8x1-1/4" Screws (E).
14.
To make sure the bed is square, measure the distance between opposing corners. If one of the
measurements is larger, tap on a footboard leg until the measurement is equal. See Figure 13.
13.
Fig. 13
Fig. 14
E x 24
P