Markant MOX Pro Single User manual

MOX Pro Single installation manual [BOX A]
A
G
=
BOX A
Code Main Component Qty
A 2
B
C 6
Button head screw M10x12
(pre-installed to the beam)
F6
G2
Tool & Manpower
Manpower x1 Power Tool x1 Allen Key x1
F
8
Set screw M12x10
(pre-installed to the beam)
D
E2
Screw M5 x 20
Hi Version
4
JCBC Screw
B
CDE

E
G
E
Attach G in between E.
1 2
3 4
5 6
7 8
Attach A to each end of E.
Slot in the screw into the hole and press it downward to secure its
position.
Tighten the screw (C) using Allen key. Repeat STEP 3 & 4 on the
other side of the end leg. The torque to tighten the screw between
receiver and leg is 22Nm to 28Nm.
Tighten the pre-instalaled screws (D) to the beam using Allen key.
Install the table top by slot in the screw (F) . Make sure the table
top is ush to the legs.
Finally, secure the table top by using self tapping screw (F).
Installation for MOX Pro single is completed. Loosen the screw (B) at
the bottom of the leg to adjust the height of the workstation and
tighten it back once reaching to the desired height.
C
A
E
G
*press downward
D
F
*flush
E
*loosen the screw at the
bottom of the leg
A
F
B

MOX Pro Combi installation manual
[BOX B (x2)]
=
BOX B (x2)
Code Main Component Qty
A 2
B
C 12
Button head screw M10x12
(pre-installed to the beam)
G 4
Tool & Manpower
Manpower x1 Power Tool x1 Allen Key x1
16
Set screw M12x10
(pre-installed to the beam)
D
E4
=
F 4
Hi Version
4
JCBC Screw
A
G
F
B
C
DE
Screw M5 x 20

E
G
E
Attach G in between E. Repeat this step 1x.
1 2
3 4
5 6
7 8
Attach A to each end of E.
Slot in the screw (C) into the hole and press it downward to secure
its position.
Tighten the screw (C) using Allen key. Repeat STEP 3 & 4 on the
other parts. The torque to tighten the screw between
receiver and leg is 22Nm to 28Nm.
Tighten the pre-instalaled screw (D) to the beam using Allen key.
Install the table top by slot in the screw (F) . Make sure the table
top is ush to the legs.
Finally, secure the table top by using self tapping screw (F).
C
A
E
G
D
E
*press downward
*flush
*MOX Pro Combi *MOX Pro Combi (Meeting Table)
F
A
Installation for MOX Pro single is completed. Loosen
the screw (B) at the bottom of the leg to adjust the
height of the workstation and tighten it back once
reaching to the desired height.
*loosen the screw at the
bottom of the leg
F
B

MOX Pro CO4 installation manual
[BOX B (x2) + BOX C]
=
BOX B (x2) + BOX C
Code Main Component Qty
A 2
B
C 24
Button head screw M10x12
(pre-installed to the beam)
E
F 12
G 8
Tool & Manpower
Manpower x1 Power Tool x1 Allen Key x1
32
Set screw M12x10
(pre-installed to the beam)
D
8
A
B
=
H2
I1
Stabiplate
Hi Version
C
D
EF
G
H
I
6
JCBC Screw
Screw M5 x 20

C
E
G
E
Attach G in between E. Repeat this step 3x.
1 2
3 4
5 6
7 8
Attach A to each end of E. Next, attach the other end part of E to I.
G
Slot in the screw into the hole and press it downward to secure its
position.
Tighten the screw (C) using Allen key. Repeat STEP 3 & 4 on the
other parts. The torque to tighten the screw between
receiver and leg is 22Nm to 28Nm.
Tighten the pre-instalaled screw (D) to the beam using Allen key.
Install the table top by slot in the screw (F) . Make sure the table
top is ush to the legs.
Finally, secure the table top by using self tapping screw (F).
E
D
A
*press downward
A
E E E
G
*flush
*MOX Pro CO4 *MOX Pro CO4 (Meeting Table)
I
F
Installation for MOX Pro single is completed.
Loosen the screw at the bottom of the leg to adjust
the height of the workstation and tighten it back once
reaching to the desired height.
*loosen the screw at the
bottom of the leg
F
B