Sensio SE30766C0 User manual

LUCIA LED MIRROR - SE30766C0 INSTALLATION INSTRUCTIONS
GENERAL
zone
2
radius
zone
2
zone
2
225cm
zone
1
60CM
60CM
60CM
The product must be installed with a
minimum distance of 150mm between
the infrared sensor and an adjacent
countertop or obstrucon to ensure correct
funcon of the sensor(see diagram le)
IMPORTANT
Please read these instrucons carefully before installaon.
Installaon should be carried out by a qualified electrician.
IEE Bathroom Zones Diagram
OUTSIDE ZONES
A1 - 2
Lucia - SE30766C0
Any Queries Call : 0845 0340 780
THIS PRODUCT CONFORMS TO UK SAFETY STANDARDS AND MUST BE INSTALLED IN
ACCORDANCE WITH CURRENT IEE WIRING REGULATIONS AND BUILDING REGULATIONS (PART P).
THIS PRODUCT MUST BE EARTHED, AND SHOULD NOT BE CONNECTED TO AN UNEARTHED CIRCUIT.
IF THERE ARE ONLY TWO WIRES COMING FROM YOUR POWER SUPPLY IT MEANS THAT THIS FITTING
CAN BE WIRED TO AN UNEARTHED CIRCUIT.
ENSURE THAT CONNECTIONS ARE TURNED OFF AT THE CONSUMER UNIT OR FUSE BOARD BEFORE
INSTALLING OR CARRYING OUT ANY MAINTENANCE.
THIS PRODUCT IS FOR IN DOOR USE ONLY.
THIS PRODUCT IS IP44 RATED AND CAN BE INSTALLED IN BATHROOM ZONE 2 (AS DEFINED BY THE IEE
WIRING REGULATIONS) AND BEYOND. SEE BATHROOM DIAGRAM BELOW.
REPLACE FAILED LAMPS IMMEDIATELY. ALLOW THE GLASS, LAMP AND FITTING TO COOL
BEFORE REPLACING THE LAMP.
Do NOT strike mirror glass with hard or pointed items. It is
recommended that the product is cleaned with a so, dry,
non abrasive cloth. Do NOT use cleaning agents or abrasive
materials on any type of finished surface. Do NOT allow
moisture to come into contact with the electrical components.
Compliance
This product complies with the following safety standards:
BS EN 60598-1: 2008+A11: 2009, EN60598-2-1: 1989
Wiring
This product is manufactured to class I category and requires
an earth connecon
COLOUR CODING:
L - Live = Brown
- Neutral = Blue
- Earth = Green & Yellow
When working at heights, please use a suitable plaorm to work from.
Please note: For new installaons, check for any electrical cables or pipe
work (gas/water) in the vicinity of the intended mounng point before proceeding
with the installaon.
Ensure that the fixing locaon is able to take the weight of the complete fing.
Wear suitable eye protecon when drilling. Be careful when using power tools near water.
MIN
150mm

LUCIA LED MIRROR - SE30766C0 INSTALLATION INSTRUCTIONS
A
2 - 2
Installaon procedure
1.Open the carton and make sure all the parts listed below are present
3.Make the electrical connecons ensuring first that the electrical supply has been turned off.
This mirror is a class 1 product and requires an earth connecon. It should be installed in
accordance with the latest IEE regulaons.
2.Mark a desired height of the mirror. Drill the required holes and insert the wall plugs.
Note: Wall plugs supplied are only suitable for solid stone/brick walls. Please ensure
the screws are fully ght. The mirror can be mounted either portrait or landscape.
Live Terminal
Connecon
Earth Terminal
Connecon
Output Wires
Neutral Terminal Connecon
Any Queries Call : 0845 0340 780
Waste Electrical & Electronic Equipment Regulaons (WEEE) requires
that any of our products showing this mark (left) must not be disposed of with
other household or commercial waste. Sensio Ltd does not levy any WEEE
disposal charges to its customers for affected WEEE related products. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate any such product from other waste types and
recycle it responsibly at your local facilities. Check with your Local Authority,
Recycling Center or retailer for recycling advice.
1X
2X
2X
DISTANCE ABETWEEN
CENTRE OF BRACKETS
4.Hang the mirror onto the wall.
A
Choose desired height
from basin (must be a
minimum of 0.6m)