Larson Electronics SL-ALM User manual

Part # SL-ALM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 5
SL-ALM
LED Strobe Light with Adjusting Magnetic Base
Instruction Manual

Part # SL-ALM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 5
Thank you for your purchase of the SL-ALM LED Portable Strobe Light, the following instructions are
intended for this part number only. This light features a fully adjustable magnetic base and is battery
operated, making it extremely portable.
To begin using your LED light, take off the back plate
by unscrewing the two screws and pulling it off.
Once the battery compartment is accessible, place 4
AA batteries in each corresponding spot and replace
the back plate.
Press the yellow button on the right side of the back
of the light to activate it.
Use the tightening adjustment knobs on each side of the light base
to loosen or tighten the pivoting ability of this light.
The light and the base can be separated by pushing down
on the lever at the front of the light base to release the lock
and allowing you to slide the light out.

Part # SL-ALM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
3of 5
Safety Warnings and Ratings
For personal safety, always follow the safety instructions in this manual to ensure safe and long-
term use. Failing to do so can result in damage to the product or serious bodily injury
Warnings
To prevent serious damage to eyesight, never
look directly at light when on. DO NOT
shine light into the face of someone else.
DO NOT use this product for other than its
intended use.
DO NOT operate in close proximity of
Combustible or flammable materials.

Part # SL-ALM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
4of 5
Warranty and Disclaimer
Larson Electronics’, LLC. LarsonElectronics.com warrants this unit to be free of defects in
materials
and workmanship for a period of three (3) years from the date of purchase.
If the unit should malfunction, it must be returned to the factory for evaluation. Larson
Electronics’ Customer Service Department will issue a Returned Merchandise Authorization
(RMA) number immediately upon phone or written request. Upon examination by Larson
Electronics’, if the unit is found to be defective it will be repaired or replaced at no charge.
Larson Electronics’ WARRANTY does not apply to defects resulting from any action of the
purchaser, including but not limited to mishandling, improper interfacing, operation outside of
design limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit
shows evidence of having been tampered with or shows evidence of being damaged as a result
of excessive corrosion; or current, heat, moisture or vibration; improper specification;
misapplication; misuse or other operating conditions outside of Larson Electronics’ control.
Larson Electronics’ is pleased to offer suggestions on the use of its various products. However,
Larson Electronics’ neither assumes responsibility for any omissions or errors nor assumes
liability for any damages that result from the use of its products in accordance with information
provided by Larson Electronics’, either verbal or written. Larson Electronics’ warrants only that
the parts manufactured by it will be as specified and free of defects.
LIMITATION OF LIABILITY
The remedies of purchaser set forth herein are exclusive and the total liability of Larson
Electronics’ with respect to this order, whether based on contract, warranty, negligence,
indemnification, strict liability or otherwise, shall not exceed the purchase price of the component
upon which liability
is based. In no event shall Larson Electronics’ be liable for consequential, incidental or special
CONDITIONS
Should any Product(s) be misused in any way, Larson Electronics’ assumes no responsibility as
set forth in our basic WARRANTY / DISCLAIMER language, and additionally purchaser will
indemnify Larson Electronics’ and hold Larson Electronics’ harmless from any liability or
damage whatsoever arising out of the use of the Product(s) in such a manner.

Part # SL-ALM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
5of 5
Return Requests and Inquiries
Direct all warranty and repair requests/inquiries to the Larson Electronics’ Customer Service
Department. BEFORE RETURNING ANY PRODUCT(S) TO LARSON ELECTRONICS’,
PURCHASER MUST OBTAIN A RETURNED MERCHANDISE AUTHORIZATION (RMA)
NUMBER FROM LARSON ELECTRONICS’ CUSTOMER SERVICE DEPARTMENT (IN
ORDER TO AVOID PROCESSING
DELAYS). The assigned RMA number should then be marked on the outside of the return
package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to
prevent breakage in transit.
For WARRANTY RETURNS please have the following information available BEFORE
contacting Larson Electronics
1. Order number under which the product was PURCHASED.
2. Model and serial number of the product under warranty.
3. Repair instruction and/or specific
problems relative to the product.
For NON-WARRANTY REPAIRS consult Larson Electronics LLC for current repair charges.
Have the following information available BEFORE contacting Larson Electronics LLC:
1. Order number to cover the COST of the repair.
2. Model and serial number of product.
3. Repair instructions and/or specific
problems relative to the product.
Larson Electronics’ policy is to make running changes, not model changes, whenever an
improvement is possible. This affords our customers the latest in technology and engineering.
Larson Electronics’ is a registered trademark of LARSON ELECTRONICS’,
LLC.
© Copyright 2017 LARSON ELECTRONICS LLC. All rights reserved. This document may not be
copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-
readable form, in whole or in part, without prior written consent of LARSON ELECTRONICS’
LLC.