SereneLife PSLMSQR10 User manual

2 Parts and Components
Body
Housingー
AC Adaptor
DC Head
Housing Retaining Screw
Power
Plug
DC Jack
Power Cord
Grid
UV Light Tube
High Voltage
Mesh
Collecting Tray
Accessories: Cleaning Brush;
Instruction Manual (this paper)
Hanging-up
This product is designed for indoor use. Do not
use it where it may get wet by rain.
This unit weights 650g. Hook up the hang ring
of the unit with a chain and hang the unit on
where it can bear the unit weight.
Suspension position of the unit should be more
than 1.8m above the floor or bed and distance
between the unit and trees or working tools
should be more than 30cm.
Power Connection
Connect the DC head of the AC adaptor to the
power outlet of the unit and plug in the unit.
Power indicator light of the high voltage mesh
and the UV light tube will both go on.
Ceiling
Wall
on the
market)
Nail Chain
(available
(available on
the market)
30cm +30cm +
1.8m+ above the bed
Trees
DC Jack
DC Head
AC Adaptor
Power Plug
Socket
Indicator Light on
(red)
UV Light
Tube on
Hang Ring
Indicator Light (red)
Disconnection of Power
Unplug the AC adaptor from the socket when the unit is not in use. Turn off the socket
for disconnection of power provided that the socket has an on/off button.
4 Maintenance
High Voltage
Prohibited
Compusive
Indicates electric shock hazard. Do not touch the high voltage
part of the unit with your hands when unit is plugged in.
Make sure you wear rubber gloves when cleaning the unit or
replacing the light tube to avoid electrical shock hazards.
●De-electrification for High Voltage Mesh
○Cleaning Instructions
Dedusting
Follow the instructions on de-electrification
for High Voltage Mesh for residual discharge
and dedust the mesh with dry cloth.
Dedust the high voltage mesh and the UV light
tube with supplied brush and make sure the
brush is dry.
① DC head must be
pulled out DC Head
Make sure the unit is unplugged (both the
adaptor plug pin and the DC head connected
with the unit need to be pulled out) when
cleaning the unit or replacing the light tube.
Please be reminded that the high voltage
mesh may still be electriferous within
certain time after unplugged.
Touch the high voltage mesh with an insulating
screwdriver for de-electrification. Do not start
any maintenance before sparks go off. ② Use a screwdriver with
plastic handle (insulating)
for de-electrification.
Cleaning Brush
Warning
Warning
Prohibited
Prohibited
Do not wet the brush with water or any detergent, otherwise it
may get you electric shocked.
Do not use detergent of any kind for cleaning, otherwise it
may result in discoloration, deformation or fire hazard.
Contrarotate the collecting tray, pull it
downwards and take out for cleaning.
Dry it before assembly after rinse. Clean it with
soft cloth and mild cleaning solution if it gets
dirty. Dry it before
assembly after
rinse.
Compusive
For the sake of security, do not take out unit housing when the
DC head is connected. Before removing the housing, make sure
the unit is de-electrificated according to instructions on
de-electrification for High Voltage Mesh after unplugged.
Unscrew the
Cleaning of the Collecting Tray Pull out after
contrarotation
Cleaning of Housing
Follow the instructions on de-electrification
for High Voltage Mesh for residual discharge
before cleaning.
②Rinse the housing with flowing water and clean it with soft cloth if it gets dirty.
Air dry the housing where it is well ventilated and out of sunlight.
Reassembly the unit with airdried housing. Residual moisture may result in
electric shock or product failure.
① Unscrew the top of the unit, contrarotate
the upper part of the unit, pull up and
take out the high voltage mesh along with
the UV light tube.
Air dry the
housing after
rinse.
Do not use hard or
rough object, detergent,
or abrasive cleaning
agents for cleaning.
Do not wash
with water.
Keep away
from water.
AC Adaptor
Prohibited
Compusive
Do not use hard or rough object, detergent, or abrasive cleaning
agents when cleaning the housing, otherwise TiO2 coating may fall off
and carbon dioxide release in the reaction of UV and TiO2 may be reduced.
Do not wash the parts or components except for the collecting tray
and the housing, otherwise it may cause product failure.
3 Installation Instructions 5 UV light tube replacementIt is recommended that the UV light tube should be
replaced on seasonal basis due to its consumable feature.
Warning
Warning
Caution
Follow the instructions on de-electrification for High
Voltage Mesh for residual discharge.
Housing remove the
housing after
residual
discharge
take out 3 screws
at the bottom
High voltage mesh
Electric-shock
unit
housing Take out electric-
shock unit
Electric-
shock
unit
Electric-shock Unit
Follow the instructions on de-electrification
for High Voltage Mesh for residual
discharge before replacing the light tube.
a. Remove the housing before taking out the
screws at the bottom of the electric-shock
unit;
b. Take down the triangular cover and take
out the light tube;
c. Insert the terminal of the substitutive light
tube correctly and sufficiently;
d. Assemble the triangular cover back with
screws and fit the housing.
UV light tube specification: FL-4BL, 4W replace the
UV light tube Electric-
shock
unit
High voltage mesh
UV light tube
Prohibited
Compusive
Do not deform the high voltage mesh, otherwise it may cause interference
among adjacent wires and cause short circuit or product failure.
Make sure the housing is well assembled before checking if the light
tube is serviceable when plugged, otherwise it may result in electric shock
or accident.
6 Troubleshooting Guide
To avoid any accident, immediately unplug the unit if any abnormal condition is found during use.
Read the manual carefully before repairing the unit and make sure the following items are read
through.
Consult the store where you bought the unit or our Sales Department for advises if problem(s)
still cannot be solved according to this guide.
is off
Issue
UV light tube
Cannot catch
mosquitoes
Inspection and Solution
Check if 1) the plug and the DC head are well inserted; 2) the socket is powered
on (test with other electric appliances or go for an electrician); 3) the triangular
cover at the bottom of the UV light tube was taken off(fit it on); 4) the UV light
tube needs to be replaced(replace the UV light tube).
Check if 1) the high voltage mesh gets dirty(clean it); 2) ambience is too bright
(dim the ambient lightings); 3) there is no high-voltage current(consult the
purchased store or contact us).
Inspection after use for an extended period of time
Check if problems listed below occur in the use Stop using the unit
· Burning smell
· Abnormal noise
· UV light flashes and goes off
· Sparks with cracking noise or other abnormalities
To avoid product failure or
accident caused by the listed
conditions, unplug the unit
and turn to the purchased
store for inspection or repair.
Inspection
7 Specifications Parts and components of the unit/ unit body, AC adaptor,
cleaning brush, installation instructions (this manual)
2100V(secondary voltage) ・ 10mA(secondary short circuit current)
Power Cord
Protection Apparatus
Continuous Operation
Main Material
Power（DC）
Voltage ・ Current
UV Light Tube
Power
Dimension
Weight
W158 X D158 X H282mm
about 650g（only for unit body）
ABS TiO2 Coating Aluminum Wire
Input: AC100V 50/60Hz Output: DC24V 500mA
FL-4BL（4 watt for each）
5W
about 3m
Current Fuse 2A
24 hours
Effective area of UV light tube: 30 ~ 80 m2 (the effectiveness of the UV light tube is influenced by the
ambient brightness and species of mosquito).
Carbon dioxide release by TiO2 coating is around 0.05m 3/ h when UV light tube is used as the light
source.(The efficacy may be different due to variances of operation conditions and insect species.)
This product is not designed for commercial use. Specifications of this product may be revised without
any previous notice.
8 Warranty and Service
① The Warranty Card is included into the package of the unit. Make sure the warranty card is
attached with store stamp and is filled with the purchase date(year, month, date).
② We will provide 1 year of warranty period beginning from the purchase date. Go to the
purchased store and show the Warranty Card if you need repairing service under warranty.
Refer to the Warranty Card for other details.
③ For service on expiration of warranty period, contact the purchased store or our company
for consultation.
④ Minimum duration of the performance parts of this product is 6 years after production halts.
Performance parts mean necessary parts to maintain performance of this product.
⑤ In case of any consumable requirement or that you are not clear about the after service
instructions, contact the purchased store or our company for consultation.