Shandong New Beiyang Information Technology Co., ltd. BTP-M280 Operating instructions

Feed Button Program Guide
Impact Receipt Printer
BTP-M280
Shandong New Beiyang Information Technology Co., Ltd.

BTP-M280 Feed Button Program Guide
- 1 -
Contents
Parameter Setting (Configuring) by Key-strokes............................................1
Parameter Setting by Key-strokes .................................................................1
Setting Configuration of the Printer................................................................1
Configuration of the Serial Interface...............................................................2
Hardware Setting ...........................................................................................2
Print Setting....................................................................................................3
Set Default Configuration...............................................................................3

BTP-M280 Feed Button Program Guide
Parameter Setting (Configuring) by Key-strokes
1) Press the button while turning on the printer. When ERROR LED flashes once, release the
button.
2) After the printer has printed the configuration sheet, press and hold the FEED button to
configure the printer. The main menu for the key-stroke setting procedure is printed.
3) The procedure consists of several sub-menus and step-by-step work is needed.
4) With every choice is a number. This number indicates the number of times the FEED button
has to be pressed momentarily. After this, the choice is validated by an additional, but longer
press of the FEED button (1 sec).
5) After all settings have been done, they are stored in the printer by stepping back through the
submenus to the “Main Menu” by using the number “1” plus additional press for validation.
Parameter Setting by Key-strokes
Setting Configuration of the Printer
Configuration
Mechanism
& Hardware
>4
Communic
ation
(only serial
interface)
>3
Exit With
Save
> 2
Exit
Without
Save
> 1
Print
Settings
> 5
Paper
Sensor
Settings
>6
Set
Default
Config
>7
Sensor Test
> 5
Main Menu
Select submenu:
Print Self Test
> 2
Exit
> 1
Configuration
> 3
Cutter Test
> 4
- 1 -

BTP-M280 Feed Button Program Guide
Configuration of the Serial Interface
Communication
Baud
Rates
(default:
9600 bps)
>2
Choices:
9600 bps
19200 bps
38400 bps
57600 bps
115200bps
4800 bps
2400 bps
1200 bps
Parity
(default:
none)
>3
Choices:
None
Odd
Even
Back
To
Last
Menu
>1
Data Bits
(default:
8 bits)
>4
Choices:
7 Bits
8 Bits
Stop
Bit(s)
(default:
1 Bit)
>5
Choices:
1 Bit
2 Bits
Handshaking
(default:
DTR/DSR)
>6
Choices:
DTR/DSR
XON/XOFF
Hardware Setting
Hardware Settings
Cutter
(default: enabled)
>3
Choices:
Enabled
Disabled
Mark Sensor
(default: disabled)
>2
Choices:
Enabled
Disabled
Back To Last
Menu
>1
Buzzer
(default: enabled)
>4
Choices:
Enabled
Disabled
- 2 -

BTP-M280 Feed Button Program Guide
Print Setting
Print Settings
Code Page
(default: PC 437)
>5
Choices:
PC 437
PC 850
PC 852
PC 857
PC 858
PC 860
PC 863
PC 865
PC 866
PC 1251
PC 1252
PC 1257
Katakana
CR Command
(default:
Disabled)
>4
Choices:
Enabled
Disabled
Paper Roll Width
(default:
80.0/76.0 mm)
>3
Choices:
57.5 mm
69.5 mm
80.0/76.0 mm
Dot Adjust Setting
>2
Back To Last
Menu
>1
Set Default Configuration
Set default
configuration
Set Printer To Default
Configuration
>2
Back to last Menu
>1
- 3 -