Sharp AF-Q100RX User manual

AF-Q100RX
AF-Q120RX
ORR&
RWX$
QD)
HYD6\JUHQ(
7LPHU
Ʒ
Ʒ
)DQ
6ORZHU
)DQ
)DVWHU
212))
10
10
11
11
12
13
13
14
14
14
15
15
20
15
16
17
18
20
AF-Q100RX,AF-Q120RX
THE
TO EXHAUST AIR FROM THE ROOM
16
PRECAUTIONS................................... 19
.........
....
.....
..

AF-Q100RX,AF-Q120RX
remote control
07495-1163

7\SH$
5LJKW
DFFRUGLRQ
SDQHO
)RDPWRS
ZLQGRZJDVNHW
:LQGRZVDVKVHDO
WKLQDGKHVLYHEDFNHG
/HIW
DFFRUGLRQ
SDQHO
7\SH%
7RSPRXQWLQJUDLO
:LQGRZORFNLQJ
EUDFNHW
6LOOVXSSRUW
1XW
%ROW
7\SH& 7\SH'
7RSPRXQWLQJUDLO
VHDOVWULS
ORR&
RWX$
QD)
HYD6\JUHQ(
7LPHU
Ʒ
Ʒ
)DQ
6ORZHU
)DQ
)DVWHU
212)) Remote control

WINDOW REQUIREMENTS
•These instructions are for a standard
double-hung window. You will need to
modify them for other types of windows.
CAUTION: If the sill support
bolts do not contact the window sill, or
if you have a window without a sill, you
must order accessory kit RAK87 to
properly install this air conditioner.
•All supporting parts must be secured
to firm wood, masonry or metal.
•The electrical outlet must be within
reach of the power cord.
STORM WINDOW REQUIREMENTS
A storm window frame will not allow the air
conditioner to tilt toward the outside, and
will keep it from draining properly. To adjust
for this, attach a piece of wood to the sill.
WOOD PIECES –
WIDTH: 2″
LENGTH: Long enough to fit inside the
window frame.
THICKNESS: To determine the thickness,
place a piece of wood on the sill to make
it 1/2″higher than the top of the storm
window frame or the vinyl frame.
Attach securely with nails or screws
provided by the installer.
1/2″ higher
than storm
window
frame
Storm window
frame
Wood
Sill
1/2″ higher
than vinyl frame
(on some windows)
Vinyl frame
REMOVE THE AIR CONDITIONER
FROM THE CASE
Remove and save the 2 screws from the
lower sides of the front grille.
Grasp the lower corners of the grille while
pressing in on the case sides with your
finger tips. Pull out to release and lift it up.
NOTE: Do not pull the bottom edge
toward you more than 3 Ǝor you may
damage the tabs of the grille.
Remove the ground screw from each side
of the case. Keep them in a safe location.
A
B
C

ATTACH THE TOP MOUNTING
RAIL SEAL STRIP
Remove the backing from the top mounting
rail seal strip and attach the seal strip to
the bottom of the top mounting rail, along
the front edge. Allow the seal strip to
overlap 3/8″on each end.
INSTALL THE TOP MOUNTING
RAIL ONTO THE CASE
Attach the top mounting rail onto the top
of the case with 3 Type B screws.
INSTALL THE
SIDE ACCORDION PANELS
Slide the left and right accordion panels
into the top and bottom mounting rails.
Attach the accordion panels to the case
using 3 Type A screws on each side.
A
B
PREPARE THE WINDOW
•Cut the window sash seal to the window
width and stick the adhesive side to the
bottom of the sash.
Window
sash seal
INSIDE
Top mounting rail
Remove
backing
from seal
strip
3/8″
3/8″
3/8″overlap 3/8″overlap
Top mounting rail
Seal strip
FRONT VIEW
Slide the air conditioner from the case by
gripping the base pan handle and pulling
forward while bracing the case. Do not
pull or lift on the styrofoam discharge area.
E

C
Replace the 2 ground screws removed
earlier, one on each side of the case.
IMPORTANT: The ground screws must
be reinstalled to ensure a proper ground.
Attach the front grille to the case by
inserting the tabs on the grille into the
slots on the front top of the case. Push
the grille in.
Secure the front grille to the case by
replacing the 2 screws removed earlier.
Press on the top of the grille to help with
side screw installation.
Connect power.
B
D

E
INSTALL THE AIR CONDITIONER
IN THE CASE
Slide the air conditioner into the case by
the base pan. Do not push on the controls,
styrofoam air discharge housing or the
finned coils. Make sure the air conditioner
is firmly seated.
A
SECURE THE CASE IN WINDOW AND
INSTALL FOAM TOP WINDOW GASKET
Attach the window
locking brackets (one
on each side) with
Type C screws.
Cut the foam top window gasket to the
window width.
Stuff the foam
between the
glass and the
window to
prevent air and
insects from
getting into the room.
NOTE: If the gasket supplied does not fit
your window, obtain appropriate material
locally to provide a proper installation seal.
ACAUTION:
To prevent broken glass
or damage to windows,
on vinyl or other
similarly constructed
windows, attach the
support bracket to the
window side jam.
B
C
Vinyl
9
10