Sharp PN-L703A User manual

Applicable models
PN-L703A/PN-70TA3/PN-L703B/PN-70TB3/PN-L603A/PN-60TA3/PN-L603B/PN-60TB3
LCD MONITOR
TOUCH PANEL DRIVER 2
OPERATION MANUAL
Version 1.0
for Mac

2
E
Contents
Introduction......................................................................3
System Requirements..................................................3
Setting up the Computer.................................................4
Install............................................................................4
Touch Panel Settings.......................................................5
How to congure settings.............................................5
Calibration ....................................................................7
Properties.....................................................................8
Uninstall..........................................................................10
Touch Action ..................................................................11
Important Information
• This software has been shipped after strict quality control and product inspection. If, however, you nd any failure or
malfunction, contact your product dealer.
• Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a
third party, nor for any other malfunctions or damage to this software arising during use, except where indemnity liability is
recognized under law.
• Transcribing or duplicating part or all of this manual and/or this software without permission from our company is not
permitted.
• As a part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for
product improvement without prior notice.
• The contents or details may vary depending on the screen conguration and OS version, etc.
• This manual does not contain basic operating instructions for Mac OS.
Trademarks
• Apple, Mac and Mac OS are registered trademarks of Apple Inc.
• Intel is a trademark or registered trademark of Intel Corporation or its subsidiaries in the U.S.A. and other countries.
• All other brand and product names are trademarks or registered trademarks of their respective holders.

3E
Introduction
System Requirements
The touch panel driver 2 is a program that enables you to use the touch panel to operate the computer that is connected to the
touch panel.
To use the touch panel, the touch panel must be connected to a computer, and the touch panel driver 2 must be installed on the
computer.
OS Mac OS X v10.7, Mac OS X v10.8, Mac OS X v10.9
CPU Intel processor
Memory At least 2 GB
Free space on hard drive At least 5 MB
TIPS
• Depending on the application software, touch operation may not be possible (for example, if the application processes mouse
and other operations independently).

4
E
Setting up the Computer
Install
Caution
• To install, an administrator name (user name) and password are required.
• If an older version of the touch panel driver 2 is installed, remove (uninstall) the old version before installing the touch panel
driver 2. (See page 10.)
• Do not touch the touch panel when connecting the USB cable.
If you touch the touch panel, it will lead to a malfunction. In this case, disconnect and then reconnect the USB cable.
1. Start your computer.
2. Exit all applications that are running.
3. Connect the USB cable for the touch panel to the computer.
To the USB terminal
of the PC
USB cable
USB 1 port*
USB 2 port*
* To use a touch panel with a computer connected to the bottom, connect to the USB 1 port.
To use a touch panel with a computer connected to the side, connect to the USB 2 port.
(Factory setting. Can be changed in TOUCH INPUT SELECT in the SETUP menu.)
4. Run the setup program.
(1) Double-click the “TouchPanel” folder, and then double-click the “Mac” folder.
(2) Double-click “SharpTouchPanel2.pkg”.
5. Click “Continue”.
Follow the on-screen instructions to install the driver.
• If a screen prompting you to enter the name and password appears, enter the name and password of the administrator
and click “Install Software” (or “OK”).
• If the “When this software nishes installing, you must restart your computer. Are you sure you want to install the software
now?” screen appears, click “Continue Installation”.
6. Whentheinstallationnishedscreenappears,click“Restart”.
This completes the installation of the touch panel driver 2.
Each time the computer is started, the touch panel driver 2 will start automatically to enable the touch panel to be used.

5E
Touch Panel Settings
The touch panel driver 2 starts automatically and the icon ( ) appears on the menu bar.
TIPS
• IfPN-L703A/PN-70TA3(orPN-L703B/PN-70TB3)andPN-L603A/PN-60TA3(orPN-L603B/PN-60TB3)areconnectedatthe
same time, selecting a setting item will display the screen where you can select the model to apply the setting to.
How to congure settings
nConguring settings from the menu bar
1. Click the touch panel driver 2 icon ( ) on the menu bar.
2. Click a menu to change a setting.
• CurrentResolution:Themodelcurrentlybeingusedandthecurrentscreenresolutionappear.
• Calibration:Seepage7.
• Properties:Seepage8.
• HardwareInformation:Hardwareinformationappears.
• VersionInformation:Showstheversionofthetouchpaneldriver2.
• DisableTPDriver:
Selecttodisablethetouchpanelfunction.
Todisableasingletouchpanelfunction,see“FunctionSetting”.(Seepage9.)
nConguring settings from System Preferences
1. Click “System Preferences” from the Apple menu ( ).
2. Click “SharpTouchPanel2”.
3. Click the menu and select settings.
Menu
TIPS
• Ifthe“ShowSettingUtilityinmenubar”checkmarkisremoved,thetouchpaneldriver2icon( ) does not appear on the
menu bar.

6
E
nSettings when two devices are connected at the same time
• If two displays of the same model are connected, touch operation will only be enabled on one model.
• If PN-L703A/PN-70TA3 (or PN-L703B/PN-70TB3) and PN-L603A/PN-60TA3 (or PN-L603B/PN-60TB3) are connected at the
same time, select the model to apply the touch panel settings to.
* Two models cannot be set at the same time.
1. Click “System Preferences” from the Apple menu ( ).
2. Click “SharpTouchPanel2”.
The “Device Selection” screen appears.
3. Select the model whose settings you want to change.
Touch Panel Settings

7E
Calibration
If black bands appear at the top and bottom or left and right of the screen, perform position adjustment so that the mouse cursor
correctly moves to the point that is touched.
* If black bands appear both at the top and bottom and at the left and right, the touch position is not correct. In this case, change
the display.
nCalibration Method
Follow the steps below to congure the setting.
1. Click the touch panel driver 2 icon ( ) on the menu bar.
2. Click “Calibration”.
Auto
If black bands appear on the screen, position adjustment is automatically performed.
Select “Auto” and click on “Apply”.
Manual
If the automatically adjusted touch position is not correct, enter the display resolution (width, height) and click “Apply”.
To check the monitor resolution, see the manual for the LCD Monitor.
Touch Panel Settings

8
E
Properties
Settings for the touch action can be congured in the properties.
nDouble Click Range
Set the range over which the position can shift between the rst touch and the second touch and still be recognized as a double-
click (“Narrow” (8 pixels) to “Wide” (64 pixels)). To return the setting to the default setting, click “Default” (32 pixels).
nDouble Click Speed
Set the time that is recognized as a double-click. When a second touch occurs within the set time after the rst touch, it is
recognized as a double-click.
Speed Setting (Auto)
The inside of the frame can be touched twice (double-clicked) to set the speed automatically based on the interval between the
touches.
Set Manually
The speed can be set manually from “Slow” (about 1 second) to “Fast” (about 0.3 seconds).
Test
When the inside of the frame is double-clicked by touching it twice, the screen changes. If the screen does not change, repeat
the setting.
Default
Click to restore the default setting.
TIPS
• Depending on the application software, changing the setting may not have any effect (for example, if the setting is set
separately in the application).
Touch Panel Settings

9E
nSecondary click
You can set press and hold to be recognized as a secondary click.*
Enable press and hold for secondary click
When the checkbox is selected, press and hold is recognized as a secondary click.
Press and Hold Duration
Set the time until press and hold is recognized as a secondary click (“Short” (0.5 sec) to “Long” (1.5 sec)).
Press and Hold Effective Range
Set the effective range for determination that the screen is being touched continuously (“Narrow” (0 pixels) to “Wide” (20 pixels)).
* If the Mac OS left-click long press action interferes with the press and hold action, do the following:
• Use “Click or tap with two ngers”
• Adjust “Press and Hold Duration” to a longer setting (toward “Long”)
nFunction Setting
Select the touch action to be used. (See page 11.)
Touch actions that are followed with a mark have multiple actions that can be used. Click a touch action and selected the
desired action.
Caution
• Touch actions that can be used vary depending on the OS.
*
* OS X v10.8/v10.9 only
Touch Panel Settings

10
E
Uninstall
Caution
• To uninstall, an administrator name (user name) and password are required.
1. Disconnect the USB cable.
2. Execute uninstall.
(1) Double-click the “TouchPanel” folder, and then double-click the “Mac” folder.
(2) Double-click “SharpTouchPanel2 Uninstaller.app”.
(3) Click “Uninstall”.
• If a screen prompting you to enter the name and password appears, enter the name and password of the administrator
and click “OK”.
3. Whentheuninstallnishedscreenappears,click“Quit”.
This completes the uninstallation.

11 E
Touch Action
TIPS
• To change the touch mode and so on, see the manual for
the LCD MONITOR (PN-L703A/PN-70TA3/PN-L703B/PN-
70TB3/PN-L603A/PN-60TA3/PN-L603B/PN-60TB3).
• Select the action to be used in Function Setting. (See page
9.)
• You can not only move the cursor without tap operation.
Touch actions that can be used on this device vary depending
on the OS.
OS
Touch Action
OS X
v10.7
OS X
v10.8/v10.9
Tap Yes Yes
Double-tap Yes Yes
Drag-and-drop Yes Yes
Click or tap with two ngers Yes *1Yes *1
Scroll with two ngers Yes Yes
Pinch with two ngers Yes *1Yes *1
Rotate with two ngers Yes *1Yes *1
Double-tap with two ngers Yes *1Yes *1
Scroll left or right with two ngers Yes *1, *2Yes *1, *2
Swipe with two or three ngers Yes *1, *2Yes *1, *2
Swipe with three ngers Yes *1, *2Yes *1, *2
Swipe left from the right edge with
two ngers
No Yes *1
Tap with three ngers Yes *1Yes *1
Swipe left or right with three ngers Yes *1, *2Yes *1, *2
Swipe left or right with four ngers Yes *1, *2Yes *1, *2
Swipe up with three or four ngers Yes *1, *2Yes *1, *2
Swipe down with three ngers Yes *1, *2Yes *1, *2
Swipe down with four ngers Yes *1, *2Yes *1, *2
Pinch with thumb and three ngers Yes *1Yes *1
Spread with thumb and three ngers Yes *1Yes *1
*1 The device can be switched ON/OFF.
*2
Actions can be selected. (See “Function Setting” on page 9.)
nFinger actions
Tap
Same action as left-clicking a mouse.
Touch with your nger.
Double-tap
Same action as double-clicking a mouse.
Quickly touch twice with your nger.
Drag-and-drop
Same action as drag-and-drop with a mouse.
Touch the screen with your nger and move without lifting.
When you have nished the movement, lift your nger.

12
E
TIPS
• The screen may not respond correctly in the following
cases:
Touching is too quick
The distance between the two points is too short
When the two points cross
Clickortapwithtwongers
Same action as a secondary click.
Scrollwithtwongers
Use in screens that can be scrolled.
With your two ngers touching the screen, move in the
direction you want to scroll. The screen scrolls in the direction
of the movement.
The scroll direction can be changed.
Pinchwithtwongers
Use in a screen that is capable of reduction/enlargement.
Touch the screen with two ngers and move your ngers
closer together to reduce the view, or apart to enlarge the
view.
Reduction
Enlargement
Rotatewithtwongers
Use this action in a screen that is capable of image rotation.
Touch the screen with two ngers and rotate to rotate the
screen in that direction.
Rotate two ngers in the
same direction.
Double-tapwithtwongers
Use smart zoom.
Touch Action

13 E
Scrollleftorrightwithtwongers/Swipewithtwoor
threengers
Use cross page swipe.
Swipeleftfromtherightedgewithtwongers
Display the notice center.
Tapwiththreengers
Check the tapped text in a dictionary or other resource.
Swipeleftorrightwiththreeorfourngers
Move an application to the front.
Swipeupwiththreeorfourngers
Display Mission Control.
Swipedownwiththreeorfourngers
Display Application Exposé.
Pinchwiththumbandthreengers
Touch the screen with 4 ngers, and move your thumb and 3
ngers together to open Launchpad.
Touch Action

14
E
Spreadwiththumbandthreengers
Touch the screen with 4 ngers, and move your thumb and 3
ngers apart to show the desktop.
Touch Action

PN-Lx03APN-Lx03BPN-xTA3PN-xTB3 V1.0 DM EN14E(1)