- 2 -
CONTENTS
Tray 1:
• 1X 6” longnose plier
• 1X 6” diagonal plier
• 1X 6” slip joint plier
• 1X 9” water pump plier
• 1X 8” adjustable wrench
• 9X combination wrenches
(6, 8, 10, 11, 12, 13, 14, 15,
17mm)
Tray 2:
• 11X screwdrivers
(PH3*150,
• PH1*75, PH2*100,
PH2*38, PH0*75,
PH1*100mm,
• SL6*100mm, SL5*75mm,
• SL3*75mm, SL6*38mm,
• SL4*100mm)
• 3X insulation screwdrivers
• 1X electrical tester
(100V-500V)
• 1X ratchet bit holder
(160mm)
• 1X pressure tester
(140mm)
Tray 3:
• 2X nylon spring clamps (3”)
• 1X 10” aluminum level (with
three water bubbles)
• 1X knife (155mm)
• 1X 12 oz. claw hammer
• 1X 8” kitchen scissor
• 1X electric hot glue gun
10W/110V-240V 50/60Hz
• 2X glue sticks (100m)
• 1X measuring tape (5m)
• 1X 8” wire stripping plier
• 1X roll of insulation tape
(6m) 60X fasteners (various
nails, screws etc. in plastic
case)
OPERATING THE ELECTRIC GLUE GUN
1. Attach the wire stand to tool. Snap open ends of stand into holes near nose of tool. Use this stand when
setting down the hot tool. This allows for good ventilation. Do not lay the hot tool down on its side.
2. Plug the power cord into a standard AC outlet. Use an extension cord if needed.
3. Insert glue stick into rear opening of tool.
4. Allow tool to heat 3-5 minutes before using.
5. Squeeze trigger to apply glue. Note: The amount of glue released depends on how far you squeeze the
trigger.
• 24X 25mm bits
• 9X hex keys (1.5, 2, 2.5, 3,
• 4, 5, 6, 8, 10mm)
• 1X 58mm extension bar
• 6X precision screwdrivers
• (SL1.4-1.8-2.3-3.0,PH0-PH1)
Tray 4:
• 15X ¼” sockets (4, 4.5, 5, 5.5,
6, 6.5, 7, 7.5, 8, 9, 10, 11, 12,
13, 14mm)
• 1X ¼” extension bar (4”)
• 1X ¼” extension bar
• 1X ¼” extension bar (2”)
• 1X ¼” ratchet wrench
(165mm)
• 14X ½” sockets (8, 9, 10, 11,
12, 13, 14, 15, 16, 17, 18, 19,
20, 30mm)
• 1X ½” extension bar (5”)
• 2X ½” spark plug sockets
• (16mm & 21mm)
• 2X universal joints (1/2” &
1/4”)
• 1X ½” extension bar
• 1X ½” ratchet wrench (10”)
• 1X socket holder (155mm)
• 1X flexible pipe (145mm)
Also Included:
• 1X wheeled aluminum
carrying case
6. Unplug the tool when you are finished, or
if you will not use it within two hours.
7. Do not remove the glue stick from the tool.
This may damage the tool. The melted glue inside
the tool will cool, and can be stored this way.
The glue will melt again the next time you
plug in the tool.
8. Allow tool to cool for at least 15 minutes before
storing. WARNING: Do not touch melted glue or
the hot tool nozzle. The temperature of the nozzle
reaches 350°F (193°C). Severe burns will occur.
GLUE STICK
OPENING
TRIGGER
WIRE
STAND
HOT GLUE TIP
