SHELTER JIT-304620PT User manual

SHELTER
L14xW9.15xH6.1 m
Assembl Manual
MODEL: JIT-304620PT

Congratulations on yourpurchaseofourinstantshelter. This unit is acombination
ofexcellentmanufacturingand design. Itiscomprisedofarigidframeand adurable
cover.Foreasyassembly,wehavemarkedall thepartswithcodes, withproper
installation, useand maintenance,yourunit will providemanyyearsofgood and
suitableservice.
Tools required
Thefollowinghand toolwill beneeded forproper Installation ofyournewbuilding:
12mm,14mm and 17mmOpen End Wrenches,
12mm, 14mm, 17mm Sockets orBoxWrench,
LargeFlatHead Screwdriver,
2lb maulorSledgehammer
4 FootLevel14 StepLadder
Stake&StringforaligningBasePlates&Frame
Assemblyprocedure
1. Prepare location and place all unit boxes near location sight. Performaninventory
check beforebeginning, to becertain all components are availableforinstallation.
2. Secure baseplateflanges to basesurface.
3. Assembleeverygroupofarch.
4. Begin frameassemblywith frontend arch, firstinteriorarch, purlins, etc.
5. Add to assembleother groups ofarches.
6. Install main cover overframe.
7. Install end cover over end panels.
Readall thedetailedinstructions and notices inthefollowing assembly
instructions!

Maintenance andcare
Annuallyormoreoften, the unit shouldbecompletelyinspected internallyand externallytomake
certain the unit remainsproperlyinstalled and secured .Particularattention should be paid to:
Hardware-check all carriageboltsand hardwareconnectors tobe certaintheyareinplace and
tightened.
Weathertrends,the unit willstrainagainstthe baseplateflange underwindyconditions,pegs
hardware, connectiontoframemembers shouldbe maintained tightanddepthofpegsshouldbe
checkedto be certain theyremain deeplyand firmlyset.
SnowAccumulation -All snowaccumulation on themaincovershouldbe removed assoonas
possible. Tap the main coverfromthe inside with a broomorsoft brush to clearcover.
MainCoverLacing-the polyrope thatsecuresthe maincovertothe bottomrail ofthe frame
assemblyshouldbe checked, and adjusted asneeded. The tension on the maincovershouldbe
uniformfromend andside toside. Ropeendsmustbe tied offontotheframemembers atthe ends
on each side.
Cleaning -coverand doors can be cleaned with a mixture oflightdetergentand water.Asoft bristle
brushwiththe mixturecan be used toloosen anyharddirt,mold, orbuildup on the cover.After
cleansing, the covershouldbe rinsed thoroughlytoavoidanychemicalreaction fromresidual
detergent.Allowing dirt anddebris tositon coveroveran extended timewilldamage cover
irreparably.
SevereWeather-inpreparation forinclementweather,completelysecurethe doorofyourbuildings
portable building.Allowing wind to enterend liftsthe
Thanksagainforchoosingthisqualityproduct. Thefollowingisthe
detailed assembly instructionsforyoustartingtheassembly.

Part Code Description Quantity
1 Top roof tube 8
2 Roof curving tube 12
2A Roof curving tube in the front and back panel
3 Roof curving tube at shoulder height 16
Sidewall tube 12
A Sidewall tube in the front and back panel 2
B Sidewall tube to connect the winch rail 2
5L Base flange in left corner 2
5R Base flange in right corner 2
6L Base flange for the left sidewall 6
6R Right base flange for the right sidewall 6
7 Base flange for standing legs of the door
8 Upper door track
9 Lower door track
10 Rail of front and back panel (beside the door)
10A Bottom rail for winch of mechanical door (beside the door) 2
11 Roof purlin and horizontal tube 9
12 Cover tensioning tube of front and back cover
13 Wind Brace Support 8
13A Tube clip for wind brace support 16
1 Cover Tensioning tube for roof cover 2sets
15 Door dropping tube 12sets
16 Door dropping tube at the bottom 2sets
17 Stake peg 72
18
Hexagonal bolt M10x75MM for swaged connection
2 2
18A
Hexagonal bolt M1 x30MM for base connection
66
19 Carriage bolt M10x85MM for roof purlin and horizontal
tubes connection 6
20 Hexagonal Bolt M10x30MM for the standing leg of end
panels and the wind brace support tubes
28
21 Bolt M10x90 for winch
22 Plastic cap for tensioning tube 12
23 Steel wire for roof 2
2 Steel wire for sidewall 12
25 Turnbuckle 36
25A
Clip for steel wire
72
26 Roof cover 1
27 Front and back cover 2
27A Door cover 2
28 Rope for fastening the roof cover, the door cover and the
front&back cover
15
29 Blanket 8
30 Band for tie down ratchet 16
31 Door beam 2sets
32 Components for mechanical door 2sets
33
Connection for steel wire and carriage bolt 13
3 "L" connection for steel wire and carriage bolt 25
Part List of JIT-30 620PT