SHELTER JIT-304020PT User manual

SHELTER
MODEL: JIT-304020PT
L12xW9.15xH6.1 m
Assemb y Manua

Congratulations on yourpurchaseofourinstantshelter. This unit is acombination
ofexcellentmanufacturingand design. Itiscomprisedofarigidframeand adurable
cover.Foreasyassembly,wehavemarkedall thepartswithcodes, withproper
installation, useand maintenance,yourunit will providemanyyearsofgood and
suitableservice.
Tools required
Thefollowinghand toolwill beneeded forproper Installation ofyournewbuilding:
12mm,14mm and 17mmOpen End Wrenches,
12mm, 14mm, 17mm Sockets orBoxWrench,
LargeFlatHead Screwdriver,
2lb maulorSledgehammer
4 FootLevel14 StepLadder
Stake&StringforaligningBasePlates&Frame
Assemblyprocedure
1. Prepare location and place all unit boxes near location sight. Performaninventory
check beforebeginning, to becertain all components are availableforinstallation.
2. Secure baseplateflanges to basesurface.
3. Assembleeverygroupofarch.
4. Begin frameassemblywith frontend arch, firstinteriorarch, purlins, etc.
5. Add to assembleother groups ofarches.
6. Install main cover overframe.
7. Install end cover over end panels.
Readall thedetailedinstructions and notices inthefollowing assembly
instructions!

Maintenance andcare
Annuallyormoreoften, the unit shouldbecompletelyinspected internallyand externallytomake
certain the unit remainsproperlyinstalled and secured .Particularattention should be paid to:
Hardware-check all carriageboltsand hardwareconnectors tobe certaintheyareinplace and
tightened.
Weathertrends,the unit willstrainagainstthe baseplateflange underwindyconditions,pegs
hardware, connectiontoframemembers shouldbe maintained tightanddepthofpegsshouldbe
checkedto be certain theyremain deeplyand firmlyset.
SnowAccumulation -All snowaccumulation on themaincovershouldbe removed assoonas
possible. Tap the main coverfromthe inside with a broomorsoft brush to clearcover.
MainCoverLacing-the polyrope thatsecuresthe maincovertothe bottomrail ofthe frame
assemblyshouldbe checked, and adjusted asneeded. The tension on the maincovershouldbe
uniformfromend andside toside. Ropeendsmustbe tied offontotheframemembers atthe ends
on each side.
Cleaning -coverand doors can be cleaned with a mixture oflightdetergentand water.Asoft bristle
brushwiththe mixturecan be used toloosen anyharddirt,mold, orbuildup on the cover.After
cleansing, the covershouldbe rinsed thoroughlytoavoidanychemicalreaction fromresidual
detergent.Allowing dirt anddebris tositon coveroveran extended timewilldamage cover
irreparably.
SevereWeather-inpreparation forinclementweather,completelysecurethe doorofyourbuildings
portable building.Allowing wind to enterend liftsthe
Thanksagainforchoosingthisqualityproduct. Thefollowingisthe
detailed assembly instructionsforyoustartingtheassembly.

Part Code Description Quantity
1 Top roof tube 7
2 Roof curving tube 10
2A Roof curving tube in the front and back pane 4
3 Roof curving tube at shou der height 14
4 Sidewa tube 10
4A Sidewa tube in the front and back pane 2
4B Sidewa tube to connect the winch rai 2
5L Base f ange in eft corner 2
5R Base f ange in right corner 2
6L Base f ange for the eft sidewa 5
6R Right base f ange for the right sidewa 5
7 Base f ange for standing egs of the door 4
8 Upper door track 4
9 Lower door track 4
10 Rai of front and back pane (beside the door) 4
10A Bottom rai for winch of mechanica door (beside the door) 2
11 Roof pur in and horizonta tube 42
12 Cover tensioning tube of front and back cover 4
13 Wind Brace Support 8
13A Tube c ip for wind brace support 16
14 Cover Tensioning tube for roof cover 2sets
15 Door dropping tube 12sets
16 Door dropping tube at the bottom 2sets
17 Stake peg 64
18
Hexagona bo t M10x75MM for swaged connection
220
18A
Hexagona bo t M14x30MM for base connection
58
19 Carriage bo t M10x85MM for roof pur in and horizonta tubes
connection 56
20 Hexagona Bo t M10x30MM for the standing eg of end pane s
and the wind brace support tubes
28
21 Bo t M10x90 for winch 4
22 P astic cap for tensioning tube 12
23
Stee wire for roof
24
24 Stee wire for sidewa 8
25 Turnbuck e 32
25A
C ip for stee wire
64
26 Roof cover 1
27 Front and back cover 2
27A Door cover 2
28 Rope for fastening the roof cover, the door cover and the
front&back cover
15
29 B anket 42
30 Band for tie down ratchet 14
31 Door beam 2sets
32 Components for mechanica door 2sets
33
Connection for stee wire and carriage bo t 9
34 "L" connection for stee wire and carriage bo t 25
Part List of JIT-304020PT