ShelterLogic 12'W x10'H Peak Style User manual

Page 2 05-101133-0C 09/04/07
www.shelterlogic.com
150 Callender Road
Watertown, CT 06795
12'W x10'H Peak Style Frame Assembly
End Rib
End Rib
Side Rails
Middle Ribs
Wind Brace
Wind Brace
Cover Rails
Top Rail
Layout out frame parts as shown and match up items with quantity to make
sure no parts are missing.
Please read and understand instructions
completely before assembly.
Assembly
Reference #
1
2
3
4
5
6
7
8
9
10
11
Mfg.
Part #
10131
10121
10132
10125
10126
10127
10128
10133
2030
10134
2031
Assembly
Reference #
12
13
14
15
16
17
18
19
20
21
22
Mfg.
Part #
10135
10110
10111
10112
669
10210
10114
10115
10113
10223
800260
ATTENTION:
FOR MISSING OR
REPLACEMENT PARTS
OR QUESTIONS,
PLEASE CONTACT
CUSTOMER SERVICE:
1.800.524.9970
CANADA 1.800.559.6175

Basic Frame Assembly
STEP 2: ASSEMBLE END RIBS
Fig. 2
STEP 3: ASSEMBLE MIDDLE RIBS
Fig. 3
Fig.3
Fig.2
10121
2" Bolts
End Rib
STEP 1: PLOTTING THE FRAME
Fig. 1
12'
12'
Length of
Building
Before building your shelter, you should choose a flat area on your property and plot
your shelter.
1. Stake out the area for the shelter in the desired spot. The width of the area
should be at least equal to the width of the shelter and the length should be
equal to the length (“L”) of the shelter Fig. 1.
2. To be sure the staked area is square tie a rope diagonally from corner to corner.
3. Measure from where the two ropes intersect each other to all 4 corners. This
measurement should be the same. If they are not equal the stakes need to be
adjusted until the width, length and inside measurements are correct.
10132
10132
10127
10127
10125 10125
Assemble end ribs as shown in Fig. 2. Securely
fasten all of the joints with the hardware indicated.
Assemble all of the middle ribs as shown in Fig. 3. Securely fasten
all of the joints with the hardware indicated.
Fig.1
10128 10128
10223
10223
10131
2" Bolts
Middle Rib
10132
10132
10125 10125
10126 10126
Page 3
10223
10223
12'x20'x10' is the base frame dimension. Your model may have more middle ribs than shown in the illustration on pg.2. You will
receive one extra rib for every extra 4 ft. of building length that you purchase. The basic frame assembly will remain the same. The
cover will be the correct size for the length of the building.
NOTE: FRAME EXTENSION KIT

Page 4
STEP 5: INSTALL WIND BRACES
Fig. 5
STEP 6: INSTALL TOP RAIL
Fig. 6
STEP 4: INSTALL SIDE RAILS AND
SHELTERLOCK™ STABILIZER BLOCKS
Fig. 4
Fig. 5
Wind Brace
2030
10135
10135
669
2030
11102
11102
Fig. 2
Fig. 4
10210 800260
01010
Install the Top Rail
Over all Middle Ribs
Fig. 6
With help move the first end rib into the desired staked area. Place
the ShelterLock on the upright as shown in Fig. 4. From the outside
of the rib insert the bolt through the upright and then through the
ShelterLock. Place the plain end of the side rail over the bolt and
nest it into the ShelterLock. Install the nut onto the bolt and tighten.
Repeat these steps for the opposite side and all of the remaining ribs.
The side rails for the last rib will have two plain ends.
Take the wind brace and attach it between the end rib and the
first middle rib as shown in Fig. 5. Any attachments at the
cross rails should be made on the very inside of the cross rail.
Place the first top rail over the pipe on the top end connector Fig. 6. The same cross
rail should lay on top of the first middle rib as with all of the middle ribs. Secure the
rails to the frame with the hardware indicated in Fig 6. The top rail attached to the
last rib will be installed over the pipe on the top end connector.

Page 5
STEP 7: SECURE BASE FEET
Fig. 7
Fig. 7
STEP 8: INSTALL AUGER ANCHORS
Fig. 8
Fig. 8
Side View
Inside View
STEP 9: END PANEL INSTALLATION
Fig. 9A, 9B & 9C
Fig. 9A Fig. 9B
Depending on the model you have purchased, your base feet will either
fit onto the outside of the leg pole or slide into the bottom of the leg pole.
After installing the base feet line up the holes in the leg to the holes in
the feet and secure with the hardware indicated in Fig. 7.
Using a ¾” pipe or steel rod (a car tire iron works also) placed
through the eyelet of the auger; screw the anchor into the ground.
Start at the corners of the shelter and space the remaining anchors
evenly along the length of the shelter. Screw the anchor into the
ground until the eyelet is sticking out of the ground by 1-2” so it can
be anchored to the legs. Wrap the cable provided through the
eyelet of the anchor and around the frame as indicated in Fig. 8.
Secure the cable with the clamp(s) provided.
Hold the end panel at the top center with the white inner
surface facing the inside of the shelter (if you have a
white shelter the inner surface has the visible weld seams).
Carefully remove the top rail from the top bend and place
the webbing in between the two. The top rail should pass
through the loop of the webbing. Replace the top rail onto
the top bend and secure it with the hardware indicated
in Fig. 9A, 9B.
Remove the nut from the side rail and carefully pull the
side rail away from the ShelterLock (the rail only needs to
be pulled away enough to pass the webbing through the
connection). If this connection has the wind brace on it
remove the wind brace end before pulling the side rail.
When the webbing is through replace the side rail, and the
cross rail if necessary Fig 9C. Replace the nut and tighten.
Repeat this for the other side.
Locate where the webbing exits the pocket on each side of
the end panel. Pull the webbing carefully to remove the slack
from the end panel. Be careful not to pull the webbing through
the other side of the panel. Install the “S”-hook from the
ratchet into the leg of the shelter Fig 9D. Insert the webbing
into the spindle of the ratchet and pull tight. Wind the ratchet
enough so that the webbing overlaps itself. Repeat the
process on the other side of the panel. Position the end panel
so that it is centered on the building. Tighten the ratchets,
alternating from one side to the other, until the end panel is
tight. Repeat these steps on the other end of the building.
Fig. 9C Fig. 9D

Page 6
STEP 10: INSTALLING THE
COVER ON THE FRAME:
Fig. 10A, 10B, 10C & 10D
1. Lay the cover on the ground next to the
frame with the inside of the cover (the side with
the pipe pockets) facing down and the webbing
on the front and rear of the corner of the
building. Position the cover so that it is
centered on the frame, front to back. Fig. 10A
2. Fold over the side closest to the frame so
the pipe pocket is now accessible. Insert a
cover pipe at the first middle rib from the front
and the first middle rib from the rear so that it is
inserted in the pipe pocket on both ends of the
pipe but the center of the pipe is exposed. For
long buildings it may be necessary to use
additional pipes in the middle. Fig. 10B
3. Tie the rope on each of the exposed pipes
and throw the other end of the rope over the
frame. FIg. 10C
4. Move to the other side of the frame and pull
the cover over the frame with the rope. This
may require two or more people. Fig. 10D
Fig. 10A
Fig. 10B
Fig. 10C
Fig. 10D

Page 7
STEP 11: SECURE YOUR COVER:
Fig. 11A, 11B, 12 & 13
Fig. 11B
corner leg
clamps
11130
690
11106
Fig.12
middle leg
clamps
11130
11107
690
Fig.13
Outside Corner View
Fig. 11A
Install the “S”-hook from the ratchet assembly into the legs of the
shelter. Pull the webbing carefully to remove the slack from the cover.
Be careful not to pull the webbing through the opposite side of the
cover. Insert the webbing through the spindle of the ratchet and pull
tight. Wind the ratchet until the webbing overlaps itself.
Repeat these steps on the opposite side. Repeat this on
the back side of the shelter. When all of the corners
are secured move the cover front to back so that it is
centered.When the cover is centered tighten all of the
ratchets. Do this in an “X” pattern to be sure it is
tightened evenly. Fig. 11A & 11B. When the cover is
tight from end to end install the 45” cover rails. Insert
the cover rails into the pockets of the cover. Clamp the
rails to the ribs using the 3-way and 4-way clamps as
shown in Fig. 12 & 13.
Check that the rails are evenly spaced above the
ground on both sides. Push down on the connectors,
one at a time, to tighten the cover. Tighten the bolts to the
cover in place and tight on the frame.
Check and tighten
Ratchets and Cross
Rails monthly to
ensure the cover
is tight.
COVER TIGHTENING TIP
CORRECT
INCORRECT
IS YOUR COVER
PULLED CORRECTLY
ON THE FRAME?
Fig. 11B
NOTE: ShelterLogic logo should line up on the left front and right rear corners near the top rail. If it is not legible and positioned
as shown above as “incorrect”, the cover has not been put on the frame correctly.
WARNING: Serious injury to persons or property could result if cover is installed and shelter is not completed and is left
unattended. Shelter must be anchored securely until completed.

Page 8
WARNING
Prior to installation, consult with all local and municipal codes regarding the installation of temporary
shelters. Choose the location of your shelter carefully. Check for overhead utility lines, tree branches or
other structures.
• Do NOT install near roof lines or other structures that could shed snow, ice, or excessive run-off onto
your shelter.
• Do NOT install too close to other structures. A MINIMUM of 6 to 10 ft. is necessary between structures
to allow for snow removal.
• Do NOT hang objects from the roof structure or support cables.
• Do NOT smoke our use open flame devices in or around the shelter.
• Do NOT store flammable liquids (gasoline, kerosene, propane, barbeque grills, fire pits, deep fryers or
smokers inside the shelter).
• Do NOT use hard edged tools or instruments like rakes or shovels to remove snow. This could result in
punctures in the cover.
CAUTION
1. PLEASE READ AND FULLY UNDERSTAND THE INSTALLATION DETAILS AND WARNINGS PRIOR TO
FINAL INSTALLATION. IF YOU HAVE QUESTIONS IMMEDIATELY CALL THE CUSTOMER SERVICE
NUMBER LISTED ON PG. 2.
2. This product is classified as a temporary fabric covered shelter and is intended to protect what is stored
in it from basic environmental elements, including the effects of sun, rain, tree sap, bird and animal
excrement and light snow. IT IS NOT DESIGNED TO HOLD THE LOAD FROM HIGH WINDS, HEAVY
SNOW OR ICE STORMS.
3. Proper anchoring is the RESPONSIBILITY OF THE OWNER. Any shelter that is not anchored securely
and properly has the potential to blow away in high winds. ShelterLogic cannot be held responsible for
any shelter that blows away. NOTE: Your shelter’s cover can be quickly removed and stored prior to
severe weather conditions. If strong winds or severe weather is forecast in your area, we recommend
that you remove the cover.
CARE & CLEANING
A tight cover will ensure longer life and performance. Inspect and retighten the ratchet tie-downs monthly
as needed. Always maintain a tight cover. Loose fabric can accelerate deterioration of the cover.
Immediately remove any accumulated snow or ice from the roof structure with a broom, mop or other soft
sided instrument.
Do NOT use “protect and shine” or harsh or abrasive products to clean the fabric cover. Mild soap and
water is recommended to clean the fabric cover of your shelter.
WARNINGS, CAUTIONS, CARE & CLEANING