ShelterLogic 26764 User manual

Description Qty. Part #
71.4" Swedged Rafter Poles 14 802105
76" Swedged Leg Poles 14 10043
77.4" Cross Poles 18 10044
38.5" Swedged Rafter Poles 14 802104
(Top Bend, shallow bend)
3-Way Frame Connectors 2
5
10046
4-Way Frame Connectors 10048
(Side Bend, sharp bend)
3-Way Frame Connectors 10045
4-Way Frame Connectors 10047
All-Weather Cover 110179
Bolts 1/4" x 2 1/2" 28 10017
Nuts 1/4" 14 1010
Wing Nuts 14 7000
Feet Plates 14 10050
Bungee Cords 48 10066
7802103
14 10052
05-26764-0C
PAGE 1
11/01/07
18X40
orPlease read instructions completely bef e assembly
10 10051
4
10
410056
Model #26764
PREMIUM INDUSTRIAL CANOPY
Twist Tite Set
TM (bungee & S hook)
Long Pins w/rings 1/4" x 2 7/8"
Short Pins w/rings 1/4" x 2 1/4"
14
Anchors
10431
ATTENTION: PINS
Pins are for legs and feet
only , and are
NOT
needed
for any other part of the
frame.
Long Pins secure feet plates to legs.
Short Pins secure legs to side bends.
Recommended Tools
Adjustable
wrench
Ratchet with
7/16 "
Safety Glasses
Ladder
Rubber Mallet
Tape Measure
Before You Start
• 2 or more persons recommended
to assemble
• Estimated assembly time = 2 hours
Truss
Manufactured Under
U.S. Patents
D415,571 D409,310
D430,306 D414,564
Other Patents Pending
150 Callender Road
Watertown, CT 06795
800.524.9970
www.shelterlogic.com

PAGE 2
1. Frame Assembly
4. Attaching Legs
3. Place Cover
Side Bend Connectors
(sharp bend)
Top Crest Connectors
(shallow bend)
802105 802105802104 802104
802105 802105802104 802104
802105 802105802104 802104
802105 802105802104 802104
802105 802105802104 802104
802105 802105802104 802104
802105 802105802104 802104
10048
10046
10046 10048
10045
10045 10047
10045
10046
10045
10047
10044 10044 10044
10044 10044 10044
10044 10044 10044
10044 10044 10044
10044 10044 10044
10044 10044 10044
10047
10045
10048
10047 10047
10048
10047 10047
10048
10047 10047
10048
10047 10047
Assembly is easiest if you layout all parts as
shown. There are (14) #802105 Rafter Poles ,
they are swedged on both ends. (14) #802104
Rafter Poles, they are swedged end. The (18)
#10044 Cross Poles do not have swedged
ends. It is very important that you determine
which of the 3 & 4 way connectors are meant
for the sides and which are for the crest.
assembly together as shown in Fig. 1A. Assemble each side of the roof as shown in Fig. 2. Install #802103 truss
as shown in Fig. 2A.
Start with center, Fig. 1, using layout shown in diagram above. Bolt roof
Assemble Roof
Fig. 2
10043
Fig. 1
Note: Install all carriage bolts
with nut toward center of frame.
01010
10017
Fig. 1A
Place cover over frame so that the
grommeted portion is face down,
this allows the valance to wrap
around and cover the frame eaves.
Insert #10043 Leg Poles on one side of the frame, swedged
end up, then the end legs on that same side. Repeat for the
other side. Now you can secure the legs to the side bend
connectors and secure the cover with bungee cords.
10017
7000
Fig. 2A
802103

7. Twist Tite
8. Attaching &
Securing base
Feet
7.1 To get your cover to fit
snugly over the frame, "twist"
each corner leg pole equally
until the cover becomes very
tight. (pictureA). Make sure
to line up the hole in the top
of the leg with the hole in the
corner side bends.
7.2 Picture B To keep the leg
Insert Base Feet Plates onto
bottom of legs, be sure to line
up the pre-drilled hole in the leg
with the pre-drilled hole in the
base foot. Insert long pins all
the way through leg and foot,
to other side, secure with ring.
B
6. Securing Cover
Working inside, under-neath the unit, begin with the corners.
Insert the cord of the bungee-ball through the grommet and
around the Cross Pole, then around the ball. By doing
this from the inside it will hide the bungee-ball and give a cle-
aner look. When all 4 corners are secured, work from side to
side to get an even fit.
PAGE 3
5. Securing Legs
Short Pins are used to secure legs to
side bend connectors.
TM
in place, wrap the bungee cord
around the cross rail, insert "S"
hook into lined up hole of leg
pole and 3 way connector. Do
this for each corner.

PAGE 4
9. Anchoring
Locate a suitable location to place one anchors
as shown in the illustration into each of the base
feet until the round end of the anchor touches the
base feet.