ShenPaz Blazir User manual

Ver 1.11 2018
1

Ver 1.11 2018
2
Table of Contents
`
Table of Contents ........................................................................................................................................2
1. Explanation of Symbols .......................................................................................................................4
2. General Safety Instructions.................................................................................................................4
2.1 Location and environmental conditions.........................................................................................7
2.2 Rating & Fuses: ...............................................................................................................................7
2.3 Power Source:..............................................................................................................................7
2.4 Standards and approvals: ................................................................................................................8
CE Declaration of Conformity..................................................................................................................8
3. Machine specifications..........................................................................................................................10
3.1 Delivery Scope...........................................................................................................................10
3.2 Intended Use .............................................................................................................................11
3.3 Components and Interfaces ............................................................................................................12
3.4 Display , screens overview and programming possibility...............................................................14
Icons: .....................................................................................................................................................14
1. NEW PROGRAM -...............................................................................................................................15
2.VIA SCREEN.........................................................................................................................................18
3-PRESET PROGRAMS............................................................................................................................20
SETTINGS SCREEN :................................................................................................................................23
ADVANCE SETTING SCREEN...................................................................................................................25
“Edit Via “advance setting........................................................................Error! Bookmark not defined.
Edit Product name....................................................................................Error! Bookmark not defined.
How to connect furnace to a device: ....................................................................................................28
How to upload sintering program files..................................................................................................30
How to upload Software........................................................................................................................31
Manufacture calibration........................................................................................................................32

Ver 1.11 2018
3
Via preset..................................................................................................Error! Bookmark not defined.
Wifi Preset : ...........................................................................................................................................30
4. Installation.........................................................................................................................................32
4.1 Setting Up ......................................................................................................................................33
4.2 Installation of the heating rod elements.........................................................................................34
Dismantling the Furnace Cover .............................................................................................................34
Earthing cable........................................................................................................................................34
Mounting the Heating Rods ..................................................................................................................34
Closing back the Furnace Cover ............................................................................................................36
5-Electrical Connection..............................................................................................................................37
6. Start a Sintering program: .....................................................................................................................37
7. Recovery function..................................................................................................................................38
8.Maintenance and cleaning .....................................................................................................................38
9. Warranty and service ............................................................................................................................39
10. Disclaimer:...........................................................................................................................................39
11. Appendices :........................................................................................................................................41

Ver 1.11 2018
4
1. Explanation of Symbols
Warning indications
Warning indications in the text are marked with a color-backed triangle and boxed.
In case of hazards through electricity, the exclamation mark in the warning triangle is
substituted by a lightning bolt.
Signal words at the beginning of a warning indication specify the type and severity of the
consequences, if the measures to avert the hazard are
not adhered to.
NOTE means that property damage can occur.
CAUTION means that light to fairly serious personal injury can occur.
WARNING means that serious personal injury can occur.
DANGER means that serious personal injury can occur.
Other symbols in the Manual
Important information that do not lead to hazards for humans or property damage are
marked with the icon aside and are also boxed.
EN
2. General Safety Instructions
When installing, starting-up and operating the machine, always observe the following safety
instructions:
DANGER:
This product does not comply with the Directive.
Do not use in explosive atmospheres!
Do not operate with explosive gases or mixtures!
CAUTION:
A defective machine can lead to malfunctions!
On detection of damage or a functional defect of the machine:
Label the machine as defective.
▷Prevent further operation until the machine has been repaired.

Ver 1.11 2018
5
NOTE:
Switch the machine off when not in use or unsupervised for longer periods, e.g., overnight.
This method of saving electrical energy also benefits the environment.
NOTE:
Increased wear of door insulation, insulation, heating rods and furnace housing!
Avoid opening the furnace when in hot condition (above 300 °C the furnace is Locked)
NOTE:
Before opening the furnace while Power is “off” from the back, you must be sure that the
furnace is cold or below 300 ° C- any other use can brake the furnace Heating element, or
burn the paint.( IF FURNACE IS SHUT OFF FROM BACK ROCKER SWITCH NO SECURITY
PROTECT USER FROM OPENING THE FURNACE IN HOT TEMPERATURE THE ELECTRICAL
PROTECTION IS OFF)
NOTE:
Starting-up and operation of the machine may only be carried out by trained specialized
personnel.
WARNING:
Operation with power sources, products, consumables, auxiliary aids, etc., which
are subject to the Ordinance on Hazardous Substances or in any way has an impact
on the health of the operating personnel is not permitted.

Ver 1.11 2018
6
Warning
ATTENTION!
ATTENTION!
Mount on non-flammable surface material only!
Take out the furnace with the assistance of two persons. To do so, each person will take a side
by holding the bottom of the furnace with one hand and the top side with the other hand.
Do not pull out the furnace by its support in order to avoid damages.
CAUTION:
PLEASE READ THE INSTRUCTIONS
CAREFULLY BEFORE OPERATING
THE FURNACE.
•Only use ZrO2 powders with recognized approval for use in dental furnaces.
•During use the area around the furnace table is very hot approach and contact
with the door and top of the furnace. Take out the tray only when the furnace is
cold.
•Dental work must only be placed on the furnace tray.
•In the event of an external power failure while the furnace is in operation:
1) Disconnect the power supply cord from the electrical power outlet.
2) Use only authorized Supply cord with the right voltage -230 V 50Hz/ 60
Hz(supply with the furnace)

Ver 1.11 2018
7
2.1 Location and environmental conditions
a) Altitude up to 2000 meters;
b) Ambient Temperature 5ºC to 40ºC;
c) Maximum relative humidity 80% for temperature up to 31ºC decreasing linearly
relative humidity at 40ºC;
d) Mains supply voltage fluctuations up to + - 10% of the nominal voltage;
e) Transient over voltages typically present on the mains supply category II;
f) Applicable rated pollution –Degree “2”
g) distance fron electrical plug must be up to 2 Meters
2.2 Rating & Fuses
230V 50Hz/60Hz
Circuit breakers fuse 16 A/230V
Circuit Breakers Auto 10KW fuse
2.3 Power Source
Caution!
Risk or Danger
Refer to documentation.
Caution!
Risk of electric shock
Caution!
Hot surface!

Ver 1.11 2018
8
Connect the furnace to a grounded power outlet socket.
Be certain that the power supply conforms to the electrical specifications of the
Blazir.
A single source of electricity must be used.
2.4Standards and approvals
CE Declaration of Conformity
This product was designed and manufactured based on careful selection of the
harmonized standards to be observed, as well as additional technical specifications. It
thus corresponds with the state-of-the-art and ensures maximum safety.
In terms of design and performance, this product complies with the European
Directives and the supplementary national requirements. Conformity has been
confirmed with the CE marking. The product's Declaration of Conformity.
1. CE –Tested to 61010-1:2001 (3rdEdition); EN61010-1;2001(3rd Edition)
2. ICES-003 Issue 4:2004 CAN/CSA-CE/IEC CISPR 22:02
3. Intertek ETL Listed - Conforms to UL Std. 61010-1 Certified to CAN/CSA Std.
61010-1
C us
4006694
Conforms to UL Std. 61010-1 Certified CAN/CSA Std. 61010-1

Ver 1.11 2018
9
“This product has been tested to the requirements of CAN/CSA-C22.2 No. 61010-1, Third edition,
including Amendment 1, or a later version of the same standard incorporating the same level of testing
requirements
Class A equipment
Equipment suitable for use in all establishments other than domestic and those directly
connected to a low voltage power supply network which supplies buildings used for
domestic purposes.

Ver 1.11 2018
10
3. Machine specifications
Blazir is a sintering furnace for dental zirconia oxide materials.
3.1 Delivery Scope
1 High-temperature furnace, model name, Blazir
4 SiC Heating rods
1 Mains cable 2 meters
1 Sintering tray
After unpacking, check the machine for completeness and possible transport
damages.
Please claim any transport damages immediately with your supplier.
For transport note that the heating element are removed to avoid any damage

Ver 1.11 2018
11
3.2 Intended Use
Blazir is a high-temperature furnace for sintering milled ZrO2units up to 1530°C. The
compact furnace is a table-top model. This high-temperature furnace has been
specially developed for sintering most of the standard Zirconia products on the
market. Only the Zirconia materials whose properties and sintering temperatures are
known may be used in the furnace.
Any other or further-going use, such as the processing of other products than those
intended for, as well as the handling of hazardous substances or materials hazardous
to one's health, does not apply as under the intended use.
As to the materials being used in the furnace, it must be known whether they are
aggressive to or even could lead to destruction of the insulation of the heating rods. It
is prohibited to remove safety devices, bypass them or put them out of operation.
Unauthorized modifications/alterations of the machine shall also void the warranty.
The set-up instructions and the safety regulations must be followed, as otherwise the
furnace is considered as not being used as intended for, and any
and all claims against Shenpaz shall become void.

Ver 1.11 2018
12
3.3 Components and Interfaces
Figure 1- Main screen
Fig 2-b: Furnace door, open
Fig 2-c: LCD touch screen
Figure 2 - Furnace overview, front
Figure 3 - Top cover with exhaust airpipe

Ver 1.11 2018
13
Figure 4 - Mounted SiC heating rods, furnace top
`
Figure 5 - Back panel, connections
MACHINE SPECIFIC
Emergency switch
Main rocker switch
Ethernet connection
Electric socket
Fuse compartment

Ver 1.11 2018
14
ATIONS
3.4 Display , screens overview and programming possibility
The display is a touch screen. For editable fields, pop-up keypads will open.
Icons:
Home icon, bring you back to homepage
Setting, bring you to internal setting of the furnace
Info, the version of the software
Save, Keep in memory programs and parameters
Ramp, Speed of heating up or down
Target temperature, the temperature the furnace is heating to
Time of holding on Step
Showing on the right of the screen a running cycle: Blue is cooling and
cold mode. Red: Firing mode. Pressing this icon will revert to graph
screen.
Exit button / to shut down the furnace it is recommended to use this
button
Next screen
Previous screen
Delete / step/ program/value
Edit program or view before starting cycle
Search- a specific program or cycle
Start Cycle / from the graph screen only
Stop cycle / from the graph screen

Ver 1.11 2018
15
1. MAIN SCREEN -
After turning on the furnace by flipping the main switch at the back of the furnace, the
Logo “SHENPAZ” will appear for few seconds, followed by the main screen.
There are 3 ways to start to operate the furnace:
1. Add a new program
2. VIA system
3. Select existing preset programs
4.
Figure 6 - Main screen
1. NEW PROGRAM
Create a new program that is not in the furnace preset database.
Select the icon “New Program” from the Main screen.

Ver 1.11 2018
16
There are two methods to create a new program.
a. Select the ZrO2brand from pre-listed brands, assign a new name, and edit the
parameters.
b. After creating a name, manually enter all new parameters.
a. A screen will prompt you to choose a listed product and assign a new name.
After assigning a name, presses create.
An editing screen will open to allow you to create your own program
The Blazir allow you to program without any restriction any profile of cycle from 1 step
up and one step down to an unlimited quantity of steps according to the different
requirement of the ZR manufacturer.

Ver 1.11 2018
17
In case of error, the field will appear in reddish color, thus indicating to the user that
the parameter setting is not within range of the furnace or missing .
b. The product brand remains on default, unless edited
After assigning a name, press ACCEPT.
An editing screen will open to allow you to create your own program

Ver 1.11 2018
18
Choose program name from list or use the Generic option
2.VIA SCREEN
By selecting the icon “VIA – simple sintering” in the Main Screen, you will access the
Shenpaz easy sintering Wizard. A limited list of tested ZrO brands are preset under
VIA.

Ver 1.11 2018
19
Figure 9 - VIA Simple Sintering screen
After selecting an available ZrO2brand from Product Name, there are 4 parameters
that need to be entered. A program will be recommended and able to be launched
automatically, once reviewed by the operator.
TRAY –select from a choice of 1,2 or 3 trays
COOLING –select normal or fast*
COLORING –select YES or NO depending if using a colorant
QUANTITY –enter total quantity of crowns
VIA will recommend a program in the Program Number field.
If acceptable, Press the “Forward” arrow icon and a graph will appear. Review the
recommended program before running the program.
Start the program by pressing the Start icon.
• FAST COOLING meaning: Activation of an internal cooling system that shortens the
overall full sintering cycle.

Ver 1.11 2018
20
3-PRESET PROGRAMS (from list)
By selecting the icon “Programs”, you access the preset list of programs in the
furnace.
Scroll to the requested program you wish to run.
Figure 10 - Program screen
Highlight the chosen program, press the icon” pencil” and the program parameters
will appear on the next screen. Only on editable cycle the Pencil will appear.