Dentsply Sirona SINIUS User manual

New as of:
Installation Instructions
07.2018
Sinius / Sinius CS / Sinius TS
English
=
Installation instructions for SINIUS sliding track treatment center, SINIUS CS, and SINIUS TS

63 22 627 D3561
2D3561.031.01.15.02 07.2018
Table of contents Dentsply Sirona
Installation Instructions Sinius / Sinius CS / Sinius TS
Table of contents
1Structure of the document........................................................................................ 6
1.1 Identification of the danger levels.................................................................. 6
1.2 Formats and symbols used........................................................................... 6
2General safety information ....................................................................................... 7
2.1 Qualification of service personnel ................................................................. 7
2.2 Power connection.......................................................................................... 7
2.3 Modifications and extensions of the system.................................................. 7
2.4 Electrostatic discharge .................................................................................. 7
2.5 Chair reference travel.................................................................................... 7
3Preparations ............................................................................................................. 8
3.1 Required tools ............................................................................................... 8
3.2 SINIUS/SINIUS CS scope of delivery ........................................................... 9
3.3 SINIUS TS scope of delivery......................................................................... 10
3.4 Media supply ................................................................................................. 11
3.4.1 Media quality .................................................................................... 11
3.4.2 Checking the supply lines ................................................................ 13
3.4.3 Cleaning compressed air and water paths....................................... 14
4Installation ................................................................................................................ 15
4.1 Preparing the chair for installation................................................................. 15
4.2 Fastening of the base of the chair to the floor............................................... 17
4.2.1 Stability............................................................................................. 17
4.2.2 Direct floor fastening ........................................................................ 18
4.2.3 Floor fastening with adapter plate .................................................... 20
4.2.4 Floor fastening with demo plate ....................................................... 24
4.3 Installing the water unit ................................................................................. 27
4.3.1 Removing the covers of the water unit............................................. 27
4.3.2 Lifting the water unit off of the transport pallet ................................. 28
4.3.3 Fastening the water unit to the floor................................................. 28
4.3.4 Removing the transport safety devices ............................................ 30
4.3.5 Connecting the drain hose ............................................................... 31
4.4 Connecting media (air and water) ................................................................. 31
4.5 Making electrical connections ....................................................................... 33
4.6 Connecting the suction hose......................................................................... 36
4.7 Moving the patient chair upwards ................................................................. 37
4.8 Installing the assistant element ..................................................................... 37

63 22 627 D3561
D3561.031.01.15.02 07.2018 3
Dentsply Sirona Table of contents
Installation Instructions Sinius / Sinius CS / Sinius TS
båÖäáëÜ
4.8.1 Mounting the assistant element....................................................... 37
4.8.2 Connecting the assistant element ................................................... 39
4.8.3 Adjusting the brakes........................................................................ 39
4.9 Installing the SINIUS dentist element........................................................... 41
4.9.1 Mounting the dentist element .......................................................... 41
4.9.2 Further connections (HSA board).................................................... 42
4.9.3 Adjusting the dentist element .......................................................... 42
4.9.3.1 Height adjustment............................................................. 42
4.9.3.2 Adjusting the brakes......................................................... 44
4.10 Installing the SINIUS CS dentist element..................................................... 45
4.10.1 Installing the dentist element (standard position)............................ 45
4.10.2 Adjusting the brakes........................................................................ 46
4.10.3 Connecting the dentist element....................................................... 47
4.10.4 Installing the dentist element (special position)............................... 48
4.10.5 Mounting the swivel arm.................................................................. 50
4.11 Installing the SINIUS TS dentist element ..................................................... 50
4.11.1 Mounting the dentist element .......................................................... 50
4.11.2 Adjusting the brakes........................................................................ 51
4.11.3 Connecting the dentist element....................................................... 53
4.12 For motorized headrests only: Installing the backrest.................................. 54
4.12.1 Mounting the Backrest..................................................................... 54
4.12.2 Making electrical/pneumatic connections........................................ 55
4.13 Double-jointed head support only: Installing the backrest............................ 58
4.13.1 Mounting the Backrest..................................................................... 58
4.14 Installing LEDview PLUS operating lights .................................................... 59
4.14.1 Installing the support tube ............................................................... 59
4.14.1.1 Standard installation......................................................... 59
4.14.1.2 Installation with monitor adapter....................................... 61
4.14.2 Attaching the lighting support arm to the support column ............... 64
4.14.3 Mounting lamp on lamp support arm............................................... 66
4.14.4 Connecting the connection cable .................................................... 68
4.14.5 Adjusting the brakes........................................................................ 70
4.14.6 Adjusting the pneumatic spring on the support arm........................ 71
4.14.7 Attaching panels.............................................................................. 72
4.15 Installing the LEDview operating light .......................................................... 74
4.15.1 Installing the support tube ............................................................... 74
4.15.1.1 Standard installation......................................................... 74
4.15.1.2 Installation with monitor adapter....................................... 76
4.15.2 Attaching the lighting support arm to the support column ............... 78
4.15.3 Connecting the connection cable .................................................... 80
4.15.4 Adjusting the brakes........................................................................ 81
4.15.5 Adjusting the pneumatic spring on the support arm........................ 82

63 22 627 D3561
4D3561.031.01.15.02 07.2018
Table of contents Dentsply Sirona
Installation Instructions Sinius / Sinius CS / Sinius TS
4.15.6 Attaching panels............................................................................... 83
4.16 Installing the tray ........................................................................................... 84
4.16.1 Standard installation (without monitor)............................................. 84
4.16.2 Tray with monitor adapter ................................................................ 86
4.16.3 SINIUS CS: Mounting the tray on the dentist element ..................... 91
4.16.4 SINIUS TS: Mounting the tray on the dentist element ..................... 92
4.17 Connecting the PC ........................................................................................ 96
4.17.1 Connecting the Mini PC ................................................................... 96
4.17.2 Connecting the external PC ............................................................. 97
4.18 Installing the monitor ..................................................................................... 99
4.18.1 Installation on the monitor adapter................................................... 99
4.18.2 Installation on the tray support arm.................................................. 104
4.18.3 Connecting the monitor .................................................................... 109
4.19 Installing HELIODENT Plus on the support tube for the operating light........ 111
4.19.1 Scope of delivery.............................................................................. 111
4.19.2 Install the support column (if you have not done it already)............. 111
4.19.3 Mounting the Heliodent Plus wall adapter........................................ 113
4.19.4 Laying the L7 radiator cable from the wall adapter to the dental
treatment center
114
4.19.5 Connecting the Power Cable to the Wall Adapter............................ 115
4.19.6 Installing the distribution box............................................................ 117
4.19.7 Installing the support arm................................................................. 118
4.19.8 Installing the scissor arm.................................................................. 119
4.19.9 Routing Radiator Cable L1 in the Water Unit ................................... 121
4.19.10 Connecting the Radiator Cables L1 and L7 ..................................... 122
4.19.11 Final tasks........................................................................................ 124
4.20 Connecting the instrument hoses.................................................................. 125
4.20.1 SINIUS dentist element.................................................................... 125
4.20.2 SINIUS CS dentist element.............................................................. 125
4.20.3 SINIUS TS dentist element .............................................................. 126
4.20.4 Assistant element............................................................................. 126
4.21 Plugging in connector X1 of cable L440........................................................ 127
5Commissioning, demo mode and repacking ............................................................ 128
5.1 Starting up the treatment center.................................................................... 128
5.2 Checking and adjusting the operating pressures of the instruments ............ 129
5.2.1 Factory settings................................................................................ 129
5.2.2 Setting the electric motors................................................................ 129
5.2.3 Setting the driving air pressure (if necessary).................................. 130
5.2.4 Adjusting the spray air pressure....................................................... 132
5.2.5 Air/water factory settings.................................................................. 132
5.3 Adjusting the spring force of the flex arm on the dentist element ................. 134

63 22 627 D3561
D3561.031.01.15.02 07.2018 5
Dentsply Sirona Table of contents
Installation Instructions Sinius / Sinius CS / Sinius TS
båÖäáëÜ
5.3.1 Preparation...................................................................................... 134
5.3.2 Setting the spring force on the CS assistant element ..................... 134
5.3.3 Setting the spring force on the TS assistant element...................... 135
5.4 Set the opening time of the cuspidor bowl valve .......................................... 136
5.5 Setting the wireless foot control on the treatment center ............................. 136
5.6 Finishing the water unit ................................................................................ 137
5.6.1 Attaching the covers of the water unit ............................................. 137
5.6.2 Inserting the tumbler outlet.............................................................. 138
5.6.3 Inserting the cuspidor bowl.............................................................. 139
5.7 Safety checks............................................................................................... 139
5.8 Finishing the chair ........................................................................................ 139
5.8.1 Attaching the covers........................................................................ 139
5.8.2 Attaching the armrest ...................................................................... 140
5.8.3 Attaching the backrest and head pads............................................ 142
5.8.4 Attaching the seat upholstery and footrest...................................... 142
5.9 Configuring the network ............................................................................... 145
5.9.1 Starting the network configuration................................................... 145
5.9.2 Description of the static and dynamic network configuration .......... 145
5.9.3 Setting up the static network configuration...................................... 146
5.9.4 Setting up the dynamic network configuration................................. 147
5.10 Sanitation procedure .................................................................................... 147
5.11 Handing over the Technical Documents and accessories to the customer.. 148
6Packing position ...................................................................................................... 149

63 22 627 D3561
6D3561.031.01.15.02 07.2018
1Structure of the document Dentsply Sirona
1.1Identification of the danger levels Installation Instructions Sinius / Sinius CS / Sinius TS
1Structure of the document
1.1 Identification of the danger levels
To prevent personal injury and material damage, please observe the
warning and safety information provided in these operating instructions.
Such information is highlighted as follows:
Tip: Information for simplifying work.
1.2 Formats and symbols used
The formats and symbols used in this document have the following
meaning:
DANGER
An imminent danger that could result in serious bodily injury or death.
WARNING
A possibly dangerous situation that could result in serious bodily injury
or death.
CAUTION
A possibly dangerous situation that could result in slight bodily injury.
NOTE
A possibly harmful situation which could lead to damage of the product
or an object in its environment.
IMPORTANT
Application instructions and other important information.
Prerequisite
1. First action step
2. Second action step
or
➢ Alternative action
Result
➢Individual action step
Prompts you to do something.
See "Formats and symbols used
[→6]"
Identifies a reference to another
text passage and specifies its page
number.
● List Designates a list.
“Command / menu item” Indicates commands / menu items
or quotations.

63 22 627 D3561
D3561.031.01.15.02 07.2018 7
Dentsply Sirona 2General safety information
Installation Instructions Sinius / Sinius CS / Sinius TS 2.1Qualification of service personnel
båÖäáëÜ
2General safety information
2.1 Qualification of service personnel
Installation and startup may be carried out only by personnel specifically
authorized by Dentsply Sirona.
2.2 Power connection
2.3 Modifications and extensions of the system
For reasons of product safety, this product may be operated only with
original Dentsply Sirona parts or third-party parts expressly approved by
Dentsply Sirona. In the event of changes which were not foreseen,
Dentsply Sirona is not liable for resulting damages.
All units connected to this product must comply with the applicable
standards:
● IEC 60601-1, Medical electrical equipment
● IEC 60950-1, Information technology equipment
● IEC 62368-1, Audio/video, information and communication
technology equipment
2.4 Electrostatic discharge
Use an ESD wrist band. Connect it to the protective ground conductor.
Please comply with the usual precautionary measures for handling
printed circuit boards (ESD). Make sure you touch a ground point to
discharge yourself prior to touching the components. Otherwise, electrical
components of the device can be destroyed.
2.5 Chair reference travel
It is prohibited for any persons to be located in the movement range of the
chair during a reference travel.
The reference travel will start only if all safety switches are inactive.
WARNING
Shock hazard
It is essential that you switch off the power supply PRIOR to beginning
the installation. There is a risk of electric shock. People can be injured
or electrical components of the unit destroyed.

63 22 627 D3561
8D3561.031.01.15.02 07.2018
3Preparations Dentsply Sirona
3.1Required tools Installation Instructions Sinius / Sinius CS / Sinius TS
3Preparations
3.1 Required tools
Tools
Supplement for the operating light
● Retaining ring pliers for outside rings (shaft)
Ø 7mm
19mm
17mm
Ø 12mm

63 22 627 D3561
D3561.031.01.15.02 07.2018 9
Dentsply Sirona 3Preparations
Installation Instructions Sinius / Sinius CS / Sinius TS 3.2SINIUS/SINIUS CS scope of delivery
båÖäáëÜ
3.2 SINIUS/SINIUS CS scope of delivery
*Cannot be supplied to every country!
A Chair H Dentist element
B Backrest I Water unit
C Footrest J *
LEDviewPLUS operating light
D Upholstery K *
LEDviewPLUS operating light
support arm
E Assistant element L Support column
F Accessories M *LEDview operating light
G Accessories
SINIUS
Wassereinheit
WaterUnit
Unitèd’e
au
UnidaddeaguaMadeinGermany
T h e D e n t a l Company
10%
95%
-40°C
+70°C
50
kPa
106
3
2
Polstersatz
Upholsteryset
Sellerie
MadeinGermany
The Dental Company
10% 10%
95%
-40°C-40°C
+70°C+70°C
50
kPakPa
106
Juegodetapizadoacolchado
The Dental Company
MadeinGermany
LEDview
The
D ental Company
The Dental Company
SINIUS
Arztelement
DentistElement
Elémentpraticien
MadeinGermany
The Dental Company
10% 10%
95% 95%
-40°C
-40°C
+70°C +70°C
50 50
kPa
106
106
3
2
Elementodelodontólogo
SINIUS
Assistenzelement
Assistant Element
Elément assistante
The
D ental Company
10% 10%
95% 95%
-40°C
-40°C
+70°C +70°C
50
kPakPa
106 106
3
2
Elemento de la asistente Made in Germany
The
Dental CompanyThe De n t a l Co m p a n y
The
Dental
CompanyTheDental Company
Madein GermanyMadein Germany
MadeinGermanyMadeinGermany
HYBRID
HYBRID
Zubehör
Zubehör
The
Dental Company
The
Dental
Company
Madein Germany
MadeinGermany
SINIUS
SINIUS
Zubehör
Zubehör
The
D ental Company
10% 10%
95% 95%
-40°C
-40°C
+70°C
+70°C
50 50
kPa
106
106
3
2
SINIUS
Patientenstuhl
Patient Chair
Fauteuil patient
Sillón dental
0123
Made in Germany
Polstersatz
Upholsteryset
Sellerie
MadeinGermany
The Dental Company
10%10%
95%95%
-40°C -40°C
+70°C
+70°C
50 50
kPakPa
106 106
Juegodetapizadoacolchado
I
H
G
F
E
D
C
B
A
The
Dental
Company
Tragarm Behandlungsleuchte
supportarm operatinglightMadeinGermany
The
Dental
Company
Behandlungsleuchte
operatinglightMadeinGermany
J
K
M
L

63 22 627 D3561
10 D3561.031.01.15.02 07.2018
3Preparations Dentsply Sirona
3.3SINIUS TS scope of delivery Installation Instructions Sinius / Sinius CS / Sinius TS
3.3 SINIUS TS scope of delivery
*Cannot be supplied to every country!
A Chair G AccessoriesI
B Backrest H Water unit
C Footrest I *
LEDviewPLUS operating light
D Upholstery J *
LEDviewPLUS operating light
support arm
E Assistant element K Support column
F Dentist element L *LEDview operating light
HYBRID
Wassereinheit
WaterUnit
Unitèd’e
au
UnidaddeaguaMadeinGermany
Th e D ental Company
10%
95%
-40°C
+70°C
50
kPa
106
3
2
Polstersatz
Upholsteryset
Sellerie
Madein Germany
The
D ental
C ompany
10%
10%
95% 95%
-40°C -40°C
+70°C
+70°C
50 50
kPakPa
106
106
Juegode tapizado acolchado
TheD ental Company
MadeinGermany
LEDview
The Dental Company
HYBRID
Assistenzelement
AssistantElement
Elémentassistante
The
Dental
Company
10% 10%
95% 95%
-40°C
-40°C
+70°C +70°C
50 50
kPakPa
106
106
3
2
Elementodela asistenteMadein Germany
TheDental CompanyTheDental Company
MadeinGermanyMadein Germany
Zubehör
Zubehör
Th e D ental Company
10% 10%
95% 95%
-40°C -40°C
+70°C +70°C
50
kPakPa
106 106
3
2
HYBRID
Patientenstuhl
Patient Chair
Fauteuil patient
Sillón dental
0123
Made in Germany
Polstersatz
Upholsteryset
Sellerie
Madein Germany
Th e D ental Company
10%
10%
95%
95%
-40°C
-40°C
+70°C +70°C
50 50
kPakPa
106 106
Juegode tapizado acolchado
TheDental
CompanyTheDental Company
MadeinGermany
MadeinGermany
HYBRID
HYBRID
Arztelement
DentistElement
Elémentpraticien
The
Dental
Company
10% 10%
95%
95%
-40°C
-40°C
+70°C
+70°C
50 50
kPakPa
106 106
3
2
Elementodel odontólogo
MadeinGermany
The
Dental
Company
TragarmBehandlungsleuchte
supportarmoperatinglightMadeinGermany
The
Dental
Company
Behandlungsleuchte
operatinglightMadeinGermany
H
F
E
D
C
B
A
G
I
J
L
K