Sherpa ST-MT340 User manual

OPERATOR’S MANUAL
ST-MT340
MULTI-TOOL
IMPORTANT! IT IS ESSENTIAL THAT YOU READ THE INSTRUCTIONS IN THIS
MANUAL BEFORE ASSEMBLING, OPERATING AND MAINTAINING THIS MACHINE.

WARNING LABELS ON THE MACHINE
Never modify your machine.
The warranty is void if you make any modication
to the machine or if you do not observe the
proper usage guidance written in this manual.
PETROL / OIL MIXTURE
AIR FILTER COVER
AIR FILTER COVER
Adjusting Chain Oil Flow - Pole Pruner Attachment
Turn the screw anticlockwise (as per arrow on attachment)
towards MAX increase oil ow rate.
Turn clockwise towards MIN to reduce oil ow rate.
Position: Bottom of pole pruner TRANSMISSION
For safe operation and maintenance, symbols are de-bossed into the machine. Observe these markings and
the associated instructions in this manual for safe operation.

FOR SAFE OPERATION
stored fuel
FOR SAFE OPERATION
’

FOR SAFE OPERATION
s

FOR SAFE OPERATION
15m
s
authorised
petrol.

FOR SAFE OPERATION
s
.

SET UP
Mount the handle between the harness attachment
point and the end of the main shaft at a position
comfortable for the user.
Insert and tighten bolts supplied to secure the handle to
the shaft in the desired position. Ensure the secondary
grip of the handle is on the left of the shaft and in the
direction as per the arrow on the grip.
Push attachment shaft into main shaft. Locate the
notch in attachment until the lever clicks closed.
Check the shaft is located by trying to remove the
attachment, it should not come out.
Then tighten knob to fully secure attachment.
Locking Lever
Tightening Knob

SET UP
While holding the unit by your right hand securely,
pull the end of the red fabric tab upwards, away from
the machine (to pull the metal retaining bar out of the
buckle). The clip will separate from the harness leaving
the unit unattached.

SET UP

SET UP

FUEL & CHAIN OIL
40
PETROL 40 : OIL 1
Petrol is very ammable.
petrol in the container.
petrol
petrol
petrol
petrol.
petrol
PETROL
petrol
Unleaded petrol is recommended to reduce the
contamination of the air for the sake of your health
and the environment.
Poor quality petrol or oil may damage the sealing
rings, fuel lines or fuel tank of the engine.
WANT TO AVOID MANY FUEL RELATED
PROBLEMS?
We recommend using Aspen 2. Aspen 2 is a ready-
mixed alkylate petrol. It contains no sulphur, benzene
or aromatics, and is therefore much better from a
health aspect to use than regular petrol.
Aspen 2 is also chemically inert so you can
comfortably leave the fuel in the machine and it
will not gum-up. It will also store for years whereas
normal petrol start to go o after 30 days.
Available in 1 & 5 Litre containers from Mower Magic

OPERATION
Set the on/o switch (1) to on (-) position.
Ensure the choke lever (CL) is in the CHOKE
position.
Prime the engine 5-10 times by pushing the down
on the primer bulb rmly (PB).
Place the unit on a at, rm surface. Keep the
cutting head clear of anything around.
While holding the unit rmly, pull the out starter
handle (SH) quickly. Repeat this until the engine
res.
Allow the engine to cut out.
Set the throttle trigger to the start position
OR set the choke lever to RUN position.
Restart the engine.
Allow the engine to warm up for a several minutes
before starting operation.
(PB)
(SH)
(CL)

OPERATION
W
(1)

OPERATION
light growth will.

OPERATION

OPERATION

OPERATION
s

OPERATION
1. Stop the engine.
2. Pull the pin (1) out.
3. Whilst holding the pin (1), pinch together
two levers (2,3) together to free the head
movement.You can now release the pin (1).
4. Holding the levers (2,3), move the handle (4) to
adjust the angle of the blades.
5. Release levers (2,3). Ensure the pin (1) clicks
back into place to lock the head.