Shimano Ultegra SM-BCR1 User manual

The following instructions must be observed at all times in order to prevent personal injury and physical damage to equipment
and surroundings.
DANGER
WARNING
CAUTION
The instructions are classified according to the degree of danger or damage which may occur if the product
is used incorrectly.
Failure to follow the instructions will result in death or serious injury.
Failure to follow the instructions could result in death or serious injury.
Failure to follow the instructions could cause personal injury or physical damage to equipment and
surroundings.
Be sure to observe the following in order to avoid burns or other injury from fluid leakages, overheating, fire or
explosions.
Input 100 -- 240 V AC, 50/60 Hz
Output 8.4 V DC, 0.55 A
Approx. 100 mm (W) x 30 mm (H) x 72 mm (D)
0 – 45 °C
-20 – 70 °C
Approx. 110 g
Dimensions
Weight
Storage temperature
Operating temperature
Main specifications
CAUTION
WARNING
Do not get the charger wet or use it while it is wet, and do not
touch or hold it with wet hands.
Do not cover the charger with a cloth or similar while it is in
use.
Do not disassemble or modify the charger.
Use the charger at the specified power supply voltage only.
Be sure to hold the power cable by the power plug when
connecting and disconnecting the power plug from the
electrical outlet.
Do not touch metallic parts of the charger or the AC adapter if
there is a lighting storm.
Do not overload the electrical outlet with appliances beyond its
rated capacity, and use only a 100 – 240 V AC electrical outlet.
Do not damage the power cord or power plug.
(Do not damage, process, forcibly bend, twist or pull them,
bring them near hot objects, place heavy objects on them or
bundle them tightly together.)
Do not use the charger with commercially-available electrical
transformers designed for overseas use, as they may damage
the charger.
Always be sure to insert the power plug as far as it will go.
If you do not hold the power cable by the power plug, fire or
electric shocks may occur.
* If heat or acrid-smelling smoke is coming out from the
power plug
* There may be a bad connection inside the power plug.
If lightning strikes, electric shocks may occur.
If the electrical outlet is overloaded by connecting too many
appliances using adapters, overheating resulting in fire may
occur.
If they are used while damaged, fire, electric shocks or
short-circuits may occur.
If this is not observed, fire may occur.
Disconnect the power plug from the electrical outlet before cleaning the charger.
If this is not observed, problems with operation or electric
shocks may occur.
If this is not observed, heat may build up and the case may
become deformed, or fire or overheating may occur.
If this is not observed, electric shocks or injury may occur.
If a power supply voltage other than that specified is used,
fire, explosions, smoke, overheating, electric shocks or
burns may occur.
SI-7DG0A-002-00
Names of parts
Charging method
Error Judgment Details
DANGER
Charger (SM-BCR1)
This charger is a special charger for use in charging Shimano lithium ion
batteries (SM-BTR1). Never insert any other type of batteries, otherwise
bursting or fire may occur.
* Make sure that you thoroughly understand the general Safety Information
for this product before use.
Special battery (SM-BTR1)
This is a lithium ion battery. Use the special charger (SM-BCR1) to charge it.
Never use any other charger to charge the battery, otherwise bursting or fire
may occur.
What to do if an error occurs
• Remove the battery from the charger,
disconnect the power plug of the
charger from the electrical outlet, and
then repeat the charging operation.
• If charging is still not possible after the
above steps have been carried out,
the ambient temperature may be too
low or too high, or there may be a
problem with the battery.
If charging is not possible, the
ERROR indicator on the charger
will flash.
Power cord
connector
Power cord:
Insert into the connector.
* Insert as far as it will go.
Electrical contacts:
If these are modified or
damaged, problems with
operation will occur.
Be very careful when
handling them.
Electrical contacts:
If these are modified or damaged,
problems with operation will occur.
Be very careful when handling them.
ERROR indicator:
This flashes when there
is an error.
CHARGE indicator:
This illuminates while
charging is in progress.
Charger cord
< Sold separately >
Type No.
USA/Canada : SM-BCC1 2
UK : SM-BCC1 6
Battery Charger
Technical Service Instructions SI-7DG0A-002
SM-BCR1
Illuminates orange
1. Insert the power plug of the charger into an electrical
outlet.
2. Insert the battery (SM-BTR1) into the charger (SM-
BCR1) as far as it will go.
* The charging time is approximately 1.5 hours.
(Note that the actual time will vary depending on
the amount of charge remaining in the battery.)
3. When the CHARGE indicator (orange)
switches off, charging is complete.
* If the ERROR indicator flashes, it
means that there may be a
problem with the battery. Refer to
"Error Judgment Details" for more
information.
4. Disconnect the power plug of the
charger from the electrical outlet and
store the charger in a suitable place
as specified in the Safety Precautions.

Please note: specifications are subject to change for improvement without notice. (English)
© Feb. 2009 by Shimano Inc. XBC IZM Printed in Japan.
One Holland, Irvine, California 92618, U.S.A. Phone: [phone]
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: [phone] Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
Disposal information for countries outside
the European Union
This symbol is only valid within the
European Union.
Contact the place of purchase or your
nearest Shimano agent for advice on
disposing of used batteries.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this manual
could void your authority to operate this equipment.