Shinwa Digital Angle Meter II User manual

ItemCode76825/ItemCode76826(withMagnet)
DigitalAngleMeterⅡ
Dust/Waterproof InstructionManual
■PartNames
■Calibration
HOLD・BEEPbutton
O N・Z E R O・ OFFbutton
1.Placethedeviceonasurfaceaslevelaspossible
andturnonthepower.
2.SimultaneouslypresstheHOLD・BEEPbuttonand
theON・ZERO・OFFbuttontodisplay .
1.Unscrewthebatterycoveronthebackand
removethebatterycover.
2.Replacethebatterieswithnewbatteries.
*Payattentiontothebatteriesorientation.
3.Replacethebatterycoverandtightenthe
screws.
MeasuringRange
MinimumIndication
Precision
90°×4directions(360°)
0.05°,0.1%,1mm/m
AutoPowerOff
Material
Accessory
Dust/waterproof
BodySize
Weight
5minutes
ABSresin,aluminum
Holdercase
IP65*3
151×60×31mm
280g(includingbattery)
0°,90°:±0.05°
OtherDegrees:±0.15°
UseTemperature
*3Dustproofperformance:Dustwillnotpenetrate.
Waterproofperformance:Itwillnotbeharmfully
affectedbywaterjetsfromanydirection.
PowerSource
−10‒50℃
2xAAAAlkalinebatteries
(Batteriesincludedarefortrialuseonly
andmaynotlastaslong)
3.PresstheON・ZERO・OFFbuttononceand 
willblinkandthenchangeto .
4.Turnitaroundonthesamesurfaceandpressthe
ON・ZERO・OFFbutton.When blinksand
changestotheangledisplay,calibrationiscomplete.
Asurfaceaslevelaspossible
Press
simultaneously
Turnaround
MeasurementreferenceplaneLiquidcrystaldisplay
LIGHT°・mm/m・%button
HOLDicon
BEEPicon
REFicon Batteryconsumptionicon
Measurementunit
icon
*1Whenthedeviceisturnedupsidedown,
themeasuredvaluedisplaywillalsorotate
soyoucanalwaysreadthenumericalvalue
displayed.
*2Whentherightofthedevice(asseenfromthe
front)isonanincreasinggradient,a+(plus)
willbedisplayed,andwhenitisonadecreasing
gradient,a−(minus)willbedisplayed.
*1
Measured
valuedisplay *2
Tiltdisplay
*Thisdeviceiscalibratedatthetimeofshipment.
Shoulditreceiveastrongimpactsuchasfrombeing
dropped,orifitisaffectedbyamagneticfield,
calibratethedeviceasfollows.
■ReplacingtheBatteries
■Specifications
Ifthebatterylevelislow,the
batteryconsumptioniconwill
appearontheLCDscreenand
startblinking.Replacewithnew
batteries.
https://www.shinwasokutei.co.jp/english/
3-18-21Koya,Sanjo,Niigata,955-8577JAPAN
MADEINCHINA
:Angle
:Gradient
:Riseper1m

■FunctionDescription
■Normalmeasurement
O N・Z E R O・ OFFbutton
Itdisplaystheanglefromthehorizontalplane.Youcanalsoswitchthemeasurementunittodisplay
risepermeterandgradient.
■Relativemeasurement
Youcansetareferencepoint(0.00°)andanyanglecanbecomethereferencepoint.(Thefollowing
explanationisforangle,buttheprocessisthesameforrisepermeterandgradient.)
■CheckingAccuracy
Turnthedevicearoundonthesamesurfaceand
checkthatthenumericalvaluesarethesame.Ifthe
differencebetweenthevaluesiswithin0.05°,the
deviceiswithintheaccuracyrange.Ifthedifference
ismorethan0.1°,calibrationisneeded.
●Ifthedeviceisnotupright,anerrorwillbedisplayed.
Pleasemakesureitisanuprightposition.
●Theaccuracyofthisproductisdescribedinthe■Specification
section.Ifhigheraccuracyisrequired,pleaseuseameasuring
instrumentwithgreateraccuracysuchasalevel.
●Donotdroporsubjecttostrongimpacts/vibrations.
●Neverdisassemblethedevice.
●Removethebatterieswhenthedevicewillnotbeusedforalong
time.
●Measurementcannotbeperformedonsurfacesotherthanthe
measurementreferenceplane.
●Keepoutofthereachofchildren.
●Whenthedisplayisasshowninthediagram
ontheright,presstheON・ZERO・OFFbutton.
●Ifthedevicegetsdirty,wipeitcleanwithasoftcloth.
Donotwipewithwater,avolatileoilsuchasthinneror
alcohol.
●Besuretochecktheaccuracybeforeuse.
Plane Plane Errordisplay
Caution
Forexample,ifyoupresstheON・ZERO・OFFbuttonat25°,thedisplaywillread0.00°andtheREFicon
willturnon.Thisisusefultocomparehowmuchofadifferencethereisbetween25°andanotherangle.
WhentheON・ZERO・OFFbuttonispressedagain,thedisplaychangestoshowtheanglefromthe
horizontalplane(usualmeasurement).
HOLD・BEEPbutton
Whenthemeasurementvalueisnotdisplayed,pressingthisbuttonwillturnthepower
ON.PressingthisbuttonwhenameasurementvalueisdisplayedwillturnontheREF
iconandsetthedevicetozero.Youcanreleasethevalueonthedisplaybypressing
thebuttonagain.Pressingandholdingwhenameasurementvalueisdisplayedwill
turnthepowerOFF.
PressingthisbuttonwhenameasurementvalueisdisplayedwillturnontheHOLD
iconandthenumericalvaluewillremainfixed.Pressingitagainreleasestheholdand
theHOLDiconwilldisappear.PressingandholdingthisbuttonwillturnontheBEEP
icon,andaBEEPwillsoundwhenthedeviceishorizontal/vertical.Thealarmsound
willstartfrom±1.4°,andtheintervalbetweenBEEPsoundsbecomesshorterasthe
devicegetsclosertohorizontal/vertical,andthenremainonelongtonewhenitis
horizontal/vertical.(Thealarmchangesinfourstages:Beep!Beep!Beep!→Bip!Bip!
Bip!→BeBeBeBeBeBeBe→Beeeeeeeeeeeeeee.)Pressandholdthebuttonagainto
cancelthealarm.
LIGHT°・mm/m・%
button
Angle
( °)
Riseper1m
(mm/m)
19.8° 360mm
Gradient
(%)
Horizontalplane
25° 26° Horizontalplane
HorizontalplaneHorizontalplane 1m Horizontalplane100
36.0
Pressingthisbuttonwhenameasurementvalueisdisplayedallowsyoutochangethe
measurementunit.(Theunitsrepeatintheorderof→mm/m→%→°).Pressingand
holdingwillturnonthebacklight.(Itwillturnoffwhenthereisnooperationforabout
27seconds,butcanbeturnedonagainbypressinganybutton.)Pressandholdagain
toturnoffthebacklight.