Endress+Hauser PROFIBUS PA Proline Promass 80 User manual

BA072D/06/en/12.05
71008416
Valid as of version:
V 2.03.XX (Device Software)
Operating Instructions
Proline Promass 80
PROFIBUS PA
Coriolis Mass Flow Measuring System
8

Brief operating instructions Proline Promass 80 PROFIBUS PA
2Endress+Hauser
Brief operating instructions
These brief operating instructions show you how to configure your measuring device quickly and
easily:
!Note!
Always start trouble-shooting with the checklist on Page 72, if faults occur after
commissioning or during operation. The routine takes you directly to the cause of the problem and
the appropriate remedial measures.
Safety instructions Page 7
▼
Installation Page 13
▼
Wiring Page 24
▼
Display and operating elements Page 35
▼
Basic configuration (device parameters, automation functions) Page 47 ff.
Device-specific parameters are configured and the automation functions specified for the
PROFIBUS interface by means of configuration programs from various manufacturers.
!Note!
If the measuring device is equipped with a local display, device-specific parameters and
functions can be configured easily and quickly using the “Commissioning” Quick Setup
menu, e.g. display language, measured variables, engineering units, signal type etc. →see
next page.
▼
System integration Page 48 ff.
Cyclic data exchange, configuration examples
▼
Application-specific commissioning Page 63 ff.
Device functions, zero point adjustment, density adjustment
▼
Customer-specific configuration Page 36 ff.
Complex measuring operations mean that additional functions must be configured. Users
can select these functions individually by means of appropriate device parameters and con-
figure and customise them to suit their process conditions.
!Note!
All functions are described in detail, as is the function matrix itself, in the “Description of
Device Functions” manual, which is a separate part of these Operating Instructions.

Proline Promass 80 PROFIBUS PA QUICK SETUP “Commissioning”
Endress+Hauser 3
QUICK SETUP “Commissioning”
!Note!
More detailed information on running Quick Setup menus, especially for devices without a local
display, can be found on Page 63 ff.
A0004749-EN
.
!Note!
• The display returns to the cell QUICK SETUP COMMISSION if you press the ESC key combina-
tion during parameter interrogation. The stored parameters remain valid.
mSelecting DELIVERY SETTINGS returns each selected unit to the factory setting.
Selecting ACTUAL SETTINGS applies the units you have set previously.
nOnly units not yet configured in the current Setup are offered for selection in each cycle. The unit for mass, volume
and corrected volume is derived from the corresponding flow unit.
oThe “YES” option remains visible until all the units have been configured. “NO” is the only option displayed when
no further units are available.
pThe “automatic parameterization of the display” option contains the following basic settings/factory settings:
YES: line 1 = mass flow; line 2 = totalizer 1
NO: The existing (selected) settings remain.
+
++
EE
HOME-POSITION
Esc
E
+
-
XXX.XXX.XX
Yes
Yes
No
No
Mass flow Volume flow Density
Selection System Units
Configuration another unit ?
Automatically configuration display ?
Temperature Quit
Unit
Mass flow
Unit
flowVolume
Unit
Density
Unit
Temperature
Measuring
Mode
Unit
Totalizer
Unit
Totalizer
Automatically
parameterization
of the display
Language
Pre-setting
Quick Setup Quick Setup
Commission
n
o
Corr. Vol. flow
Unit
Corr. Vol. flow
Unit
Ref. Density
Fix
Ref. Density
p
Selection pre-settings
Actual SettingsDeliver Settingsy
m

QUICK SETUP “Commissioning” Proline Promass 80 PROFIBUS PA
4Endress+Hauser

Proline Promass 80 PROFIBUS PA Table of contents
Endress+Hauser 5
Table of contents
1 Safety instructions . . . . . . . . . . . . . . . . 7
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.2 Installation, commissioning and operation . . . . . . . . 7
1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.4 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.5 Notes on safety conventions and icons . . . . . . . . . . . 8
2 Identification . . . . . . . . . . . . . . . . . . . . 9
2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.1 Nameplate of the transmitter . . . . . . . . . . . . 9
2.1.2 Nameplate of the sensor . . . . . . . . . . . . . . . 10
2.1.3 Nameplate, connections . . . . . . . . . . . . . . 11
2.2 CE mark, declaration of conformity . . . . . . . . . . . . 12
2.3 Device certification PROFIBUS PA . . . . . . . . . . . . . 12
2.4 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . 12
3 Installation . . . . . . . . . . . . . . . . . . . . 13
3.1 Incoming acceptance, transport and storage . . . . . . 13
3.1.1 Incoming acceptance . . . . . . . . . . . . . . . . . 13
3.1.2 Transport . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1.3 Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . 14
3.2.1 Installation dimensions . . . . . . . . . . . . . . . 14
3.2.2 Mounting location . . . . . . . . . . . . . . . . . . . 14
3.2.3 Orientation . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2.4 Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2.5 Thermal insulation . . . . . . . . . . . . . . . . . . 19
3.2.6 Inlet and outlhhet runs . . . . . . . . . . . . . . . 19
3.2.7 Vibrations . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2.8 Limiting flow . . . . . . . . . . . . . . . . . . . . . . . 19
3.3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.3.1 Turning the transmitter housing . . . . . . . . 20
3.3.2 Installing the wall-mount
transmitter housing . . . . . . . . . . . . . . . . . . 21
3.3.3 Turning the local display. . . . . . . . . . . . . . . 23
3.4 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 23
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 24
4.1 Cable specifications for PROFIBUS PA . . . . . . . . . . 24
4.2 Connecting the remote version . . . . . . . . . . . . . . . 27
4.2.1 Connecting the sensor/transmitter . . . . . . 27
4.2.2 Cable specifications, connecting cable . . . . 27
4.3 Connecting the measuring unit . . . . . . . . . . . . . . . 28
4.3.1 Connecting the transmitter . . . . . . . . . . . . 28
4.3.2 Fieldbus connector . . . . . . . . . . . . . . . . . . . 30
4.4 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . 32
4.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 33
5 Operation . . . . . . . . . . . . . . . . . . . . . 34
5.1 Operation at a glance . . . . . . . . . . . . . . . . . . . . . . . 34
5.2 Operation via the local display . . . . . . . . . . . . . . . . 35
5.2.1 Display and operating elements . . . . . . . . . 35
5.2.2 Brief guide to the function matrix . . . . . . . . 36
5.3 Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
5.4 Communication: PROFIBUS PA . . . . . . . . . . . . . . . 39
5.4.1 PROFIBUS PA technology . . . . . . . . . . . . . 39
5.4.2 System architecture . . . . . . . . . . . . . . . . . 39
5.4.3 Acyclic data exchange. . . . . . . . . . . . . . . . . 41
5.5 Operation via PROFIBUS configuration programs . . 42
5.5.1 Operating options . . . . . . . . . . . . . . . . . . . 42
5.5.2 Current device description files . . . . . . . . . . 43
5.6 Hardware configuration . . . . . . . . . . . . . . . . . . . . . 44
5.6.1 Configuring of write protection . . . . . . . . . 44
5.6.2 Configuration of the device address. . . . . . . 45
6 Commissioning . . . . . . . . . . . . . . . . . 46
6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
6.2 Commissioning via the local display . . . . . . . . . . . . 47
6.3 System integration . . . . . . . . . . . . . . . . . . . . . . . . . 48
6.3.1 Cyclic data exchange . . . . . . . . . . . . . . . . . 50
6.3.2 Configuration examples with Simatic S7 HW-
Konfig56
6.3.3 Cycle times. . . . . . . . . . . . . . . . . . . . . . . . . 61
6.4 Application-specific commissioning . . . . . . . . . . . . 63
6.4.1 Quick Setup “Commissioning” . . . . . . . . . . 63
6.4.2 Zero point adjustment. . . . . . . . . . . . . . . . . 64
6.4.3 Density adjustment . . . . . . . . . . . . . . . . . . . 66
6.5 Purge and pressure monitoring connections . . . . . . 68
6.6 Data storage device (HistoROM) . . . . . . . . . . . . . . 68
6.6.1 HistoROM/S-DAT (sensor-DAT) . . . . . . . . 68
7 Maintenance . . . . . . . . . . . . . . . . . . . 69
7.1 Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 69
7.2 Cleaning with pigs (Promass H, I) . . . . . . . . . . . . . 69
7.3 Replacing seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
8 Accessories . . . . . . . . . . . . . . . . . . . . 70
8.1 Device-specific accessories . . . . . . . . . . . . . . . . . . . 70
8.2 Measuring principle-specific accessories . . . . . . . . . 70
8.3 Service-specific accessories . . . . . . . . . . . . . . . . . . . 71
9 Trouble-shooting . . . . . . . . . . . . . . . 72
9.1 Trouble-shooting instructions . . . . . . . . . . . . . . . . . 72
9.2 System and process error messages . . . . . . . . . . . . . 74
9.3 Process errors without message . . . . . . . . . . . . . . . 86
9.4 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
9.4.1 Removing and installing electronics boards . 88
9.4.2 Replacing the device fuse . . . . . . . . . . . . . . 92
9.5 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
9.6 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
9.7 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Table of contents Proline Promass 80 PROFIBUS PA
6Endress+Hauser
10 Technical data . . . . . . . . . . . . . . . . . . 96
10.1 Technical data at a glance . . . . . . . . . . . . . . . . . . . 96
10.1.1 Applications . . . . . . . . . . . . . . . . . . . . . . . 96
10.1.2 Function and system design . . . . . . . . . . . 96
10.1.3 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
10.1.4 Output PROFIBUS PA . . . . . . . . . . . . . . . 98
10.1.5 Power supply . . . . . . . . . . . . . . . . . . . . . . 99
10.1.6 Performance characteristics . . . . . . . . . . . 99
10.1.7 Operating conditions: Installation. . . . . . . . 104
10.1.8 Operating conditions: Environment . . . . . 104
10.1.9 Operating conditions: Process . . . . . . . . . . 105
10.1.10Mechanical construction . . . . . . . . . . . . . . 113
10.1.11Human interface . . . . . . . . . . . . . . . . . . . . 116
10.1.12Certificates and approvals . . . . . . . . . . . . 116
10.1.13Ordering information . . . . . . . . . . . . . . . 117
10.1.14Accessories . . . . . . . . . . . . . . . . . . . . . . . 117
10.1.15Documentation . . . . . . . . . . . . . . . . . . . 117
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Proline Promass 80 PROFIBUS PA 1 Safety instructions
Endress+Hauser 7
1 Safety instructions
1.1 Designated use
The measuring device described in these Operating Instructions is to be used only for measuring the
mass flow rate of liquids and gases. At the same time, the system also measures fluid density and
fluid temperature. These parameters are then used to calculate other variables such as volume flow.
Fluids with widely differing properties can be measured, for example:
• Chocolate, condensed milk, liquid sugar
• Oils, fats
• Acids, alkalis, lacquers, paints, solvents and cleaning agents
• Pharmaceuticals, catalysts, inhibitors
• Suspensions
• Gases, liquefied gases, etc.
Resulting from incorrect use or from use other than that designated, the operational safety of the
measuring devices can be suspended. The manufacturer accepts no
liability for damages being produced from this.
1.2 Installation, commissioning and operation
Note the following points:
• Installation, connection to the electricity supply, commissioning and maintenance of the device
must be carried out by trained, qualified specialists authorised to perform such work by the facil-
ity's owner operator. The specialist must have read and understood these Operating Instructions
and must follow the instructions it contains.
• The device must be operated by persons authorised and trained by the facility's owner-operator.
Strict compliance with the instructions in this manual is mandatory.
• Endress+Hauser will be happy to assist in clarifying the chemical resistance properties of parts
wetted by special fluids, including fluids used for cleaning. However the user is responsible for
the choice of fluid-wetted materials as regards to their in-process resistance to corrosion. The
manufacturer refuses to accept liability.
• The installer must ensure that the measuring system is correctly wired in accordance with the
wiring diagrams. The transmitter must be grounded, unless the power supply is galvanically insu-
lated.
• Invariably, local regulations governing the opening and repair of electrical devices apply.
1.3 Operational safety
Note the following points:
• Measuring systems for use in hazardous environments are accompanied by separate “Ex docu-
mentation”, which is an
integral part of these Operating Instructions. Strict compliance with the
installation instructions and ratings as stated in this supplementary documentation is mandatory.
The symbol on the front of this supplementary Ex documentation indicates the approval and the
certification body (0Europe, 2USA, 1Canada).
• The measuring device complies with the general safety requirements in accordance with
EN 61010, the EMC requirements in accordance with EN 61326/A1 and NAMUR recommen-
dation NE 21/43.
• For measuring systems used in SIL 2 applications, the separate manual on functional safety must
be observed.
• The manufacturer reserves the right to modify technical data without prior notice. Your E+H dis-
tributor will supply you with current information and updates to these Operating Instructions.

1 Safety instructions Proline Promass 80 PROFIBUS PA
8Endress+Hauser
1.4 Return
The following procedures must be carried out before a flowmeter requiring repair or calibration, for
example, is returned to Endress+Hauser:
• Always enclose a duly completed “Declaration of Contamination” form. Only then can
Endress+Hauser transport, examine and repair a returned device.
• Enclose special handling instructions if necessary, for example a safety data sheet as per EN
91/155/EEC.
• Remove all residues. Pay special attention to the grooves for seals and crevices which could con-
tain residues. This is particularly important if the substance is hazardous to health, e.g. flammable,
toxic, caustic, carcinogenic, etc.
With Promass A and Promass M the threaded process connections must first be removed from the
sensor and then cleaned.
!Note!
You will find a
preprinted “Declaration of Contamination” form at the back of this manual.
#Warning!
• Do not return a measuring device if you are not absolutely certain that all traces of hazardous sub-
stances have been removed, e.g. substances which have penetrated crevices or diffused through
plastic.
• Costs incurred for waste disposal and injury (burns, etc.) due to inadequate cleaning will be
charged to the owner-operator.
1.5 Notes on safety conventions and icons
The devices are designed to meet state-of-the-art safety requirements, have been tested, and left the
factory in a condition in which they are safe to operate. The devices comply with the applicable
standards and regulations in accordance with EN 61010 “Protection Measures for Electrical Equip-
ment for Measurement, Control, Regulation and Laboratory Procedures”. They can, however, be a
source of danger if used incorrectly or for other than the designated use.
Consequently, always pay particular attention to the safety instructions indicated in these Operating
Instructions by the following icons:
#Warning!
“Warning” indicates an action or procedure which, if not performed correctly, can result in injury
or a safety hazard. Comply strictly with the instructions and proceed with care.
"Caution!
“Caution” indicates an action or procedure which, if not performed correctly, can result in incorrect
operation or destruction of the device. Comply strictly with the instructions.
!Note!
“Note” indicates an action or procedure which, if not performed correctly, can have an indirect
effect on operation or trigger an unexpected response on the part of the device.

Proline Promass 80 PROFIBUS PA 2 Identification
Endress+Hauser 9
2 Identification
2.1 Device designation
The “Proline Promass 80 PROFIBUS PA” flow measuring system consists of the following compo-
nents:
• Proline Promass 80 PROFIBUS PA transmitter
• Promass F, Promass M, Promass E, Promass A, Promass H or Promass I sensor
In the
compact version , transmitter and sensor form a single mechanical unit; in the remote version
they are installed separately.
2.1.1 Nameplate of the transmitter
A0004708
Fig. 1: Nameplate specifications for the “Promass 80 PROFIBUS PA” transmitter (example)
1 Order code/serial number: See the specifications on the order confirmation for the meanings of the individual letters
and digits.
2 Power supply / frequency: 16 to 62 V DC / 20 to 55 V AC / 50 to 60 Hz
Power consumption: 15 VA / W
3 Available Inputs/outputs: PROFIBUS PA
4 Reserved for information on special products
5 Ambient temperature range
6 Degree of protection
Order Code:
Ser.No.:
TAG No.:
16-62VDC/20-55VAC
50-60Hz 15VA/W
IP67/NEMA/Type4X80F25-XXXXXXXXXXXX
12345678901
ABCDEFGHJKLMNPQRST
–20°C (–4°F) < Tamb < +60°C (+140°F)
i
1
6
5
2
3
4
Pat. US 5,479,007
Pat. US 4,768,384
Pat. UK 261 435
5,648,616
4,801,897
EP 262 573 EP 618 680
PROFIBUS-PA Profile 3.0
R
Promass 80
N12895

2 Identification Proline Promass 80 PROFIBUS PA
10 Endress+Hauser
2.1.2 Nameplate of the sensor
A0004688
Fig. 2: Nameplate specifications for the “Promass F” sensor (example)
1 Ordering code/Serial number: See the specifications on the order confirmation for the meanings of the individual
letters and digits.
2 Calibration factor: 2.510; zero point: –11
3 Nominal diameter device: DN 25 / 1"
4 Nominal diameter flange: DN 25 / 1"
Pressure rating: EN (DIN) PN 100 bar
5 Material of measuring tubes: Stainless steel 1.4539/904L
6 TMmax +200 °C / +392 °F (max. fluid temperature)
7 Pressure range of secondary containment: max. 40 bar (600 psi)
8 Accuracy of density measurement: ± 0.001 g/cc
9 Additional information (examples):
– With 5-point calibration
– With 3.1 B certification for fluid wetted materials
10 Reserved for information on special products
11 Ambient temperature range
12 Degree of protection
13 Flow direction
14 Reserved for additional information on device version (approvals, certificates)
1
2
4
5
6
7
8
9
11
12
13
200°C / 392°F
40 bar / 600 psi Container
2.5100 / -11
DN25 / 1" EN (DIN) PN100
1.4539 / 904L
5P-CAL, 3.1B
Density cal.:
-20°C (-4°F)<Tamb<+60°C (+140°F)
Pat. US 5,796,011
Materials:
TMmax.:
Order Code:
K-factor:
TAG No.:
Ser.No.:
IP67/NEMA/Type4X
+/-0.001g/cc
XXF25-XXXXXXXXXXXX
12345678901
ABCDEFGHJKLMNPQRST
i
14
DN25 / 1"
Size : 3
10
Promass F
N12895
2005
4153 Reinach Switzerland

Proline Promass 80 PROFIBUS PA 2 Identification
Endress+Hauser 11
2.1.3 Nameplate, connections
A0001665
Fig. 3: Nameplate specifications for Proline transmitter (example)
1 Serial number
2 Not for PROFIBUS PA communication type
3 Not for PROFIBUS PA communication type
4 Terminal assignment, cable for power supply: 85 to 260 V AC, 20 to 55 V AC, 16 to 62 V DC
Terminal No. 1: L1 for AC, L+ for DC
Terminal No. 2: N for AC, L- for DC
5 Signals present at inputs and outputs, possible configuration and terminal assignment (20 to 27), see also
“Electrical values of inputs/outputs”
6 Version of device software currently installed
7 Installed communication type
8 Information on current communication software
9 Date of installation
10 Current updates to data specified in points 6 to 9
Communication:
Drivers:
Device SW:
ID 1528 (HEX)
2.03.00
PROFIBUS PA
Date: 01. NOV 04
SW–version Ex–works
26(+) / 27(-)
NC:
Versorgung /
Tension d'alimentation
Observer manuel d'instruction
See operating manual
Betriebsanleitung beachten
26=PA–
27=PA+
PROFIBUS PA
XXXXXXXXXXXSer.No.:
Supply /
24(+) / 25(-)
22(+) / 23(-)
20(+) / 21(-)
N/L-
PE
A:
NO:
P:
L1/L+
12
FEK1512–2
X
active
passive
normally open contact
normally closed contact
Update 1 Update 2
2
3
1
4
5
6
7
8
9
10

2 Identification Proline Promass 80 PROFIBUS PA
12 Endress+Hauser
2.2 CE mark, declaration of conformity
The devices are designed in accordance with good engineering practice to meet state-of-the-art
safety requirements, have been tested, and left the factory in a condition in which they are safe to
operate. The devices comply with the applicable standards and regulations in accordance with EN
61010 “Protection Measures for Electrical Equipment for Measurement, Control, Regulation and
Laboratory Procedures” and with the EMC requirements of EN 61326/A1.
The measuring system described in these Operating Instructions thus complies with the statutory
requirements of the EC Directives. Endress+Hauser confirms successful testing of the device by
affixing the CE mark.
The measuring system complies with the EMC requirements of the “Australian Communications
Authority (ACA)”.
2.3 Device certification PROFIBUS PA
The Promass 80 flowmeter has passed all the test procedures implemented and has been certified
and registered by the PNO (PROFIBUS User Organisation). The device thus meets all the require-
ments of the specifications listed below:
• Certified for PROFIBUS 3.0
Device certification number: upon request
• The instrument meets all of the PROFIBUS 3.0 specifications.
• The device may also be operated using certified devices from other manufacturers (interoperabil-
ity).
2.4 Registered trademarks
KALREZ ®, VITON ®
Registered trademarks of E.I. Du Pont de Nemours & Co., Wilmington, USA
TRI-CLAMP ®
Registered trademark of Ladish & Co., Inc., Kenosha, USA
SWAGELOK ®
Registered trademark of Swagelok & Co., Solon, USA
PROFIBUS ®
Registered trademark of PROFIBUS Nutzerorganisation e.V., Karlsruhe, D
HistoROM™, S-DAT®, ToF Tool - Fieldtool®Package, Fieldcheck®, Applicator®
Registered or registration-pending trademarks of Endress+Hauser Flowtec AG, Reinach, CH

Proline Promass 80 PROFIBUS PA 3 Installation
Endress+Hauser 13
3 Installation
3.1 Incoming acceptance, transport and storage
3.1.1 Incoming acceptance
On receipt of the goods, check the following points:
• Check the packaging and the contents for damage.
• Check the shipment, make sure nothing is missing and that the scope of supply matches your
order.
3.1.2 Transport
The following instructions apply to unpacking and to transporting the device to its final location:
• Transport the devices in the container in which they are delivered.
• The covers or caps fitted to the process connections prevent mechanical damage to the sealing
faces and the ingress of foreign matter to the measuring tube during transportation and storage.
Consequently, do not remove these covers or caps until immediately before installation.
• Do not lift measuring devices of nominal diameters DN 40 to 250 at the transmitter housing or
the connection housing in the case of the remote version (Fig. 4). Use webbing slings slung round
the two process connections. Do not use chains, as they could damage the housing.
• Promass M / DN 80: Use only the lifting eyes on the flanges to transport this sensor.
#Warning!
Risk of injury if the measuring device slips. The center of gravity of the assembled measuring device
might be higher than the points around which the slings are slung.
At all times, therefore, make sure that the device does not unexpectedly turn around its axis or slip.
A0004294
Fig. 4: Instructions for transporting sensors with DN 40 to 250

3 Installation Proline Promass 80 PROFIBUS PA
14 Endress+Hauser
3.1.3 Storage
Note the following points:
• Pack the measuring device in such a way as to protect it reliably against impact for storage (and
transportation). The original packaging provides optimum protection.
• The permissible storage temperature is −40 °C to +80 °C (preferably +20 °C).
• Do not remove the protective covers or caps on the process connections until you are ready to
install the device.
• The measuring device must be protected against direct sunlight during storage in order to avoid
unacceptably high surface temperatures.
3.2 Installation conditions
Note the following points:
• No special measures such as supports are necessary. External forces are absorbed by the construc-
tion of the instrument, for example the secondary containment.
• The high oscillation frequency of the measuring tubes ensures that the correct operation of the
measuring system is not influenced by pipe vibrations.
• When mounting, no special precautions need to be taken for fittings which create turbulence
(valves, elbows, T-pieces, etc.), as long as no cavitation occurs.
• For mechanical reasons and in order to protect the pipe, it is advisable to support heavy sensors.
3.2.1 Installation dimensions
All the dimensions and lengths of the sensor and transmitter are provided in the separate documen-
tation “Technical Information”.
3.2.2 Mounting location
Entrained gas bubbles in the measuring tube can result in an increase in measuring errors. For this
reason, avoid the following mounting locations:
• Highest point of a pipeline. Risk of air accumulating.
• Directly upstream of a free pipe outlet in a vertical pipeline.
A0003605
Fig. 5: Mounting location

Proline Promass 80 PROFIBUS PA 3 Installation
Endress+Hauser 15
The proposed configuration in Fig. 6, however, permits installation in a vertical pipeline. Pipe
restrictors or the use of an orifice with a smaller cross-section than the nominal diameter prevent
the sensor from running empty during measurement.
A0003597
Fig. 6: Installation in a vertical pipe (e.g. for batching applications)
1Supplytank
2Sensor
3 Orifice, pipe restrictions (see Table)
4 Valve
5 Batching tank
System pressure
It is important to ensure that cavitation does not occur, because it would influence the oscillation
of the measuring tube. No special measures need to be taken for fluids which have properties similar
to water under normal conditions.
In the case of liquids with a low boiling point (hydrocarbons, solvents, liquefied gases) or in suction
lines, it is important to ensure that pressure does not drop below the vapour pressure and that the
liquid does not start to boil. It is also important to ensure that the gases that occur naturally in many
liquids do not outgas. Such effects can be prevented when system pressure is sufficiently high.
Consequently, it is generally best to install the sensor:
• downstream from pumps (no danger of vacuum),
• at the lowest point in a vertical pipe.
Promass F, M, E / DN 81525405080
1) 1002) 1502) 2502)
∅Orifice plate, pipe restriction [mm] 610142228506590150
1) Promass F, M only
2) Promass F only
Promass A / DN 124
∅Orifice plate, pipe restriction [mm] 0.8 1.5 3.0
Promass H, I / DN 81515
1) 25 251) 40 401) 50 501) 802)
∅Orifice plate, pipe restriction [mm] 6101514242235 28 54 50
1) DN 15, 25, 40, 50 “FB” = Full bore versions of Promass I
2) Promass I only
1
2
3
4
5

3 Installation Proline Promass 80 PROFIBUS PA
16 Endress+Hauser
3.2.3 Orientation
Make sure that the direction of the arrow on the nameplate of the sensor matches the direction of
flow (direction in which the fluid flows through the pipe).
Orientation Promass A
Vertical:
Recommended orientation with upward direction of flow. When fluid is not flowing, entrained sol-
ids will sink down and gases will rise away from the measuring tube.
The measuring tubes can be completely drained and protected against solids build-up.
Horizontal:
When installation is correct the transmitter housing is above or below the pipe. This arrangement
means that no gas or solid deposits can accumulate in the curved measuring tube (single-tube sys-
tem).
Do not install the sensor in such a way that it is suspended in the pipe, in other words without sup-
port or attachment. This is to avoid excessive strain at the process connection. The base plate of the
sensor housing is designed for mounting on a tabletop, wall or post.
A0003606
Fig. 7: Vertical and horizontal orientation (Promass A)

Proline Promass 80 PROFIBUS PA 3 Installation
Endress+Hauser 17
Orientation Promass F, M, E, H, I
Make sure that the direction of the arrow on the nameplate of the sensor matches the direction of
flow (direction in which the fluid flows through the pipe).
Vertical:
Recommended orientation with upward direction of flow (View V). When fluid is not flowing,
entrained solids will sink down and gases will rise away from the measuring tube. The measuring
tubes can be completely drained and protected against solids build-up.
Horizontal (Promass F, M, E):
The measuring tubes of Promass F, M and E must be horizontal and beside each other. When
installation is correct the transmitter housing is above or below the pipe (View H1/H2). Always
avoid having the transmitter housing in the same horizontal plane as the pipe.
Horizontal (Promass H, I):
Promass H and Promass I can be installed in any orientation in a horizontal pipe run.
Promass F, M, E, H, I Standard, compact Promass F, M, E, H, I Standard, remote Promass F High-temperature, compact Promass F High-temperature, remote
Fig. V: Vertical orientation
A0004572
ÃÃ ÃÃ ÃÃ ÃÃ
Fig. H1: Horizontal orientation
Transmitter head up
A0004576
ÃÃ ÃÃ ✘ (TM = >200 °C)
m
Ã
(TM = >200 °C)
m
Fig. H2: Horizontal orientation
Transmitter head down
A0004580
ÃÃ
n
ÃÃ
n
ÃÃ
n
ÃÃ
n
ÃÃ = Recommended orientation
Ã= Orientation recommended in certain situations
✘= Impermissible orientation

3 Installation Proline Promass 80 PROFIBUS PA
18 Endress+Hauser
In order to ensure that the maximum permissible ambient temperature for the transmitter
(-20 °C to +60 °C, optional -40 °C to +60 °C) is not exceeded, we recommend the following
orientations:
m= For fluids with very high temperatures (> 200 °C), we recommend the horizontal orientation
with the transmitter head pointing downwards (Fig. H2) or the vertical orientation (Fig. V).
n= For fluids with low temperatures, we recommend the horizontal orientation with the
transmitter head pointing upwards (Fig. H1) or the vertical orientation (Fig. V).
Special installation instructions for Promass F, E and H
"Caution!
The two measuring tubes of Promass F and Promass E and the one of Promass H are slightly curved.
The position of the sensor, therefore, has to be matched to the fluid properties when the sensor is
installed horizontally .
A0004581
Fig. 8: Promass F, E, H installed horizontally
1 Not suitable for fluids with entrained solids. Risk of solids accumulating.
2 Not suitable for outgassing fluids. Risk of air accumulating.
3.2.4 Heating
Some fluids require suitable measures to avoid loss of heat at the sensor. Heating can be electric,
e.g. with heated elements, or by means of hot water or steam pipes made of copper.
"Caution!
• Risk of electronics overheating! Consequently, make sure that the adapter between sensor and
transmitter and the connection housing of the remote version always remain free of insulating
material. Note that a certain orientation might be required, depending on the fluid temperature
→ Page 17 ff. (Orientation Promass F, M, E, H, I)
• With a fluid temperature between 200 °C to 350 °C, heating is not permitted for the compact
version of the high-temperature version.
When using electrical heat tracing whose heat is regulated using phase control or by pulse packs,
it cannot be ruled out that the measured values are influenced by magnetic fields which may
occur, (i.e. at values greater than those permitted by the EC standard (Sinus 30 A/m)). In such
cases, the sensor must be magnetically screened (except for Promass M).
The secondary containment can be shielded with tin plates or electric sheets without privileged
direction (e.g. V330-35A) with the following properties:
– Relative magnetic permeability µr≥300
– Plate thickness d ≥0.35 mm
• Information on permissible temperature ranges → Page 96 ff..
Special heating jackets which can be ordered as accessories from Endress+Hauser are available for
the sensors.
12

Proline Promass 80 PROFIBUS PA 3 Installation
Endress+Hauser 19
3.2.5 Thermal insulation
Some fluids require suitable measures to avoid loss of heat at the sensor. A wide range of materials
can be used to provide the required thermal insulation.
A0004614
Fig. 9: In the case of the Promass F high-temperature version, a maximum insulation thickness of 60 mm must be
observed in the area of the electronics/neck.
If the Promass F high-temperature version is installed horizontally (with transmitter head pointing
upwards), an insulation thickness of min. 10 mm is recommended to reduce convection. The
maximum insulation thickness of 60 mm must be observed.
3.2.6 Inlet and outlhhet runs
There are no installation requirements regarding inlet and outlet runs. If possible, install the sensor
well clear of fittings such as valves, T-pieces, elbows, etc.
3.2.7 Vibrations
The high oscillation frequency of the measuring tubes ensures that the correct operation of the
measuring system is not influenced by pipe vibrations. Consequently, the sensors require no special
measures for attachment.
3.2.8 Limiting flow
Relevant information can be found in the “Technical Data” section under Measuring range
→ Page 96 or Limiting flow 105.
max. 60
Esc
E
-
+
max. 60

3 Installation Proline Promass 80 PROFIBUS PA
20 Endress+Hauser
3.3 Installation
3.3.1 Turning the transmitter housing
Turning the aluminium field housing
#Warning!
The turning mechanism in devices with EEx d/de or FM/CSA Cl. I Div. 1 classification is not the
same as that described here. The procedure for turning these housings is described in the Ex-specific
documentation.
1. Loosen the two securing screws.
2. Turn the bayonet catch as far as it will go.
3. Carefully lift the transmitter housing as far as it will go.
4. Turn the transmitter housing to the desired position (max. 2 x 90° in either direction).
5. Lower the housing into position and re-engage the bayonet catch.
6. Retighten the two securing screws.
A0004302
Fig. 10: Turning the transmitter housing (aluminium field housing)
Turning the stainless steel field housing
1. Loosen the two securing screws.
2. Carefully lift the transmitter housing as far as it will go.
3. Turn the transmitter housing to the desired position (max. 2 x 90° in either direction).
4. Lower the housing into position.
5. Retighten the two securing screws.
A0004303
Fig. 11: Turning the transmitter housing (stainless steel field housing)
3
5
6
1
24
12
3
4
5