Shinybow USA SB-6335R5 User manual

INSTRUCTION MANUAL
MODEL : SB-6335R5
HDMI HDBaseT EXTENDER
HDMI HDBaseT EXTENDER Receiver with PoH
HDMI-HDBaseT EXTENDER Series
Thank you for purchasing the SB-6335R5 HDMI-HDBaseTwith PoH Receiver. You will findthis uniteasy to install
and highly reliable but it is essential that you read this manual thoroughly before attempting to use converter.
MULTIMEDIA AUDIO AND VISUAL

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualified service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF AGENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

CONFORMANCE TEST REPORT
FOR
EN 61000-6-1 / EN 61000-6-3
EN 61000-6-1 / EN 61000-6-3
REPORT NUMBER: 09-07-MAS-282-18-R
FOR
FCC 47 CFR/Part 15 Subpart B
FCC 47 CFR/Part 15 Subpart B
Report Number: 09-07-MAS-282-19-R
Model Number: SB-6335R5
Comment Number : SB-6215, SB-6215R, SB-6215RE,
SB-6220R SB-6220RE, SB-6240R, SB-6240RE, SB-6335,
SB-6335R, SB-6320, SB-6320R
Input: HDBaseT via single CAT6/6a/7 cable
Output: HDMI & PoH (Power Over HDBaseT)
Power Input: +DC12V , 2000mA
TABLE OF CONTENTS
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow
for sufficient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed,stored in aretrieval system, orany of itsparttranslated
into any language or computer file, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without express written permission and consent.
© Copyright 1997. All Rights Reserved.
Version 1.2 MAR 2014
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
CONTENTS
INTRODUCTION ...............................................................1
FEATURES & SPECIFICATIONS ..................................... 2
PACKAGECONTENTS.....................................................2
TYPICALHOOKUPAND OPERATION ............................. 3
RACKMOUNTS(OPTIONAL)........................................... 4
IR EXTENDER ................................................................. 6
INTRODUCTION
Congratulations on your purchase of one of the most innovative
HDMI over HDBaseT with PoH (Power Over HDBaseT) Receiver
on the market today. The HDBaseT Receiver can receive the
HDMI, IR remote in, IR remote out, RS-232 in, RS-232 out,
Ethernet signals and PoH power over HDBaseT from HDBaseT
Transmitter via a single category cable for long distance muximum
928 feet (100 meters). SB-6335R5 use category cable CAT6,
CAT6a or CAT7 (UTP or FTP) with RJ-45 8P8C connector and
Support 568a or 568b color specification table. This HDBaseT
receiver product provide the higher full HD HDMI resolutions
480i/p, 720p,1080i/p quality that are identical to the source to the
HD destination display. This HDBaseT Receiver control signals
are useful to receive the HDMI digital Video, digital multi-channel
Audio signals, IR in, IR out, RS-232 in, RS-232 out, Ethernet
series interface via category cable from the HDBaseT Transmitter.
1

FEATURES & SPECIFICATIONS
FEATURES
• HDBaseT HDMI Receiver over single CAT6/6a/7 category LAN cable.
• Extend for HDMI, IR in/out, RS-232 in/out and two Ethernet ports, with HDCP compliant.
• Support category cable via using the CAT6, CAT6a and CAT7 UTP/FTP cable.
• Support link speeds of up to 3.4 Gbps
• Support Digital RGB 36bits, V1.4a HDMI TMDS format.
• Extension higher quality DVI video 1920x1200 resolution.
• Support HD High Definition full range resolution 480p, 720p 1080i/1080p
• Support long distance 100M between HDBaseT Transmitter and HDBaseT Receiver.
• Support wall mount and rack mount install for 19 inch 4U Rack mountable.
• Power support DC input with Low power consumes (Full load 850mA)
• Power supply using universal power switch 50/60Hz,100~240VAC.
SPECIFICATIONS
• Type of Extender: HDBaseT Receiver for HDMI signal over one category LAN Cable
• Input Signals: HDMI with Digital Video(TMDS)/Audio 0.5~1.0vPP, DDC 5Vpp
• HDBaseT Supports: HDMI Standard, DVI and HDCP Compliant
• Video Support: HDMI and DVI TMDS format for 1920x1200 resolution up to 3.4 Gbps Digital RGB 36bits deep color, 3D 1.4a HDMI format
• HDMI Audio Out Supports: Multi-channel Audio Formats 5.1 / 7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital Plus,
DTS, DTS-ES 6.1, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
• PoH Support: HDBaseT Receiver with PoH power over HDBaseT
• Category Cable Support: CAT6, CAT6a, CAT7 UTP/FTP cable
• Support HDMI Resolution: 480p, 720p, 1080i/1080p
• Scan Rate Accepted: Support HDMI full HD Resolutions; Frequency 24Hz to 60Hz
• Control: 1x IR in/out, 1x IR in/out, 1x RS-232 and 1x LAN series interface
• IR Infrared Frequency: 38Khz
• Extend Distance: Up to 100M (CAT6)
• Safety Approvals: CE, FCC, VCCI, REACH & WEEE
• Dimensions (LxWxH): 5.31 x 5.11 x 1 in (135mm x 130mm x 26mm)
• Rack Mount : Use total 10 pcs install into one 19 inch rack mountable
• Shipping Weight: 0.4775 kgs / 0.82 lb
• Power Consumption: Max. 0.850mA. (Full load 1080p-60Hz signal with use DC12V input)
• Power Supply: Power Input +12VDC, 2A, (Universal Type 50/60Hz, 100~240 VAC)
PACKAGE CONTENTS
Check that you have the following components;
• SB-6335R5 HDBaseT Receiver console
• SB-100 set (IR Receiver Extender assy plug).
• SB-100C cable (IR Receiver Cable).
• SB-101 set (IR Transmitter Extender assy plug).
• SB-101C cable (IR Transmitter Cable).
• 1 inch High Wall mount pack (Part # WM-1INCH-L80MM)
• Users Guide
• AC/DC Adapter: 12VDC, 2A. (universal power switch 50/60Hz,100~240VAC)
As product improvements are continuous, specifications are subject to change and without notice.
2

TYPICAL HOOKUPAND OPERATION
FRONT PANEL: SB-6335R5
1. Status via LED Show out : POWER, LINK & HDCP.
2. PoH turn ON/OFF function
3. 1x Ethernet series interface path to Transmitter.
REAR PANEL: SB-6335R5
4. DC input : DC12V, 2A
5. RJ-45 IN : HDBaseT input , Signal from the HDBaseT Transmitter
6. HDMI OUT : HDMI output , Signal to HDMI destination display device
7. IR IN : Send IR signal to HDBaseT Transmitter
8. IR OUT : Receive IR signal from HDBaseT Transmitter via IR External Receiver SB-100)
9. RS-232 I/O : RS-232 series interface in or out control via a PC
INSTALLING DIAGRAM
3

RACK MOUNT (optional)
SB-6069
SB-6335T5/SB-6335R5 19 INCH 4U-10P RACK MOUNT
Model No. : #4U-10p-L130MM
SB-6335T5/SB-6335R5 4U Ear mount pairs
Parts No.: MEER6069ER13000
Model No. : #4U-10p-L130MM-COV
SB-6335T5/SB-6335R5 4U Ear mount pairs
Parts No.: MEER6069ER11000
Model No. : #4U-10p-L80MM-EAR
SB-6335T5/SB-6335R5 4U Ear mount pairs
Parts No.: MEER6320ER11001
4

RACK MOUNT (optional)
SB-6069
Complete 19 inch 4U rack mount
Install (10 units) Application : SB-6335T5/SB-6335R5
SB-6335T5/SB-6335R5 : Wall mount accessories
Model No. : #WM-1INCH-L80MM
SB-6335T5/SB-6335R5 Wall mount pairs
Parts No.: MEER6320ER11000
5

IR EXTENDER
6
SB-100 Maximum Distance ~ 984 feet (300 meters)
SB-100 and SB-100C Receiver Pin configuration
VCC (Ring)
Signal (center)
GND (Sleeve)
Tip Ring
Sleeve
Tip: Signal
Ring :VCC
Sleeve: GND
Ring
Tip (center)
Sleeve
INP UT
DC 12V
R oHS /95/E C
IR EXT .
RS -232
RS-232 IR EXT. in
SB-100 IR Receiver Set
SB-100
IR Rx
SB-100 Maximum Distance ~ 984 feet (300 meters)
SB-100C Maximum Distance ~ 6 feet (2 meters)
SB-100C Maximum Distance ~ 6 feet (2 meters)
INP UT
DC 12V
R oHS /95/E C
IR EXT .
RS -232
RS-232 IR EXT. in
IR Receiver cable 6ft (2M)
SB-100C IR Receiver Cable
SB-100 IR Receiver Set
Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug
(aka: stereo plug). Using a 2-conductor plug will short out the power supply. Always make connections with the
switcher power off.
*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***
POWER
INPUT-1
1234
1234
1234
1234
HDMIMATRIXSWITCHER
ONOFF
INPUT-2
INPUT-3
INPUT-4
SWIR
SB-100
IR Rx
POWER
INPUT-1
1234
1234
1234
1234
HDMIMATRIXSWITCHER
ONOFF
INPUT-2
INPUT-3
INPUT-4
SW IR
IR Receiver cable 6ft (2M)
SB-100C IR Receiver Cable
1. SB-100 IR 300M Receiver Device Cable (3C) IR Receiver (SB-100)
2. SB-100C IR 2M Receiver Device Cable (3C) IR Receiver (SB-100C)
IR RECEIVER:
PIN CONFIGURATION:
Signal (center)
GND (Sleeve)
Tip Ring
Sleeve
Tip: Signal
Ring: NC
Sleeve: GND
Ring
Tip (center)
Sleeve

IR EXTENDER
7
RoHS/95/EC
DC 12V
IR out
From
Receiver
IR in
To
Receiver
CAT6/6a/7
OUTPUT
RoHS/95/EC
DC 12V
IR out
From
Receiver
IR in
To
Receiver
CAT6/6a/7
OUTPUT
IR EMITTER:
SB-101 Maximum Distance ~ 984 feet (300 meters)
PIN CONFIGURATION:
SB-101 and SB-101C Transmitter Pin configuration
SB-101 IR Transmitter Set
1. SB-101 IR 300M Transmitter Device Cable (3C) IR Transmitter (SB-101)
SB-101
IR Tx
SB-101C Transmitter Cable
IR Transmitter cable 6ft (2M)
SB-101 Maximum Distance ~ 984 feet (300 meters)
SB-101C Maximum Distance ~ 6 feet (2 meters)
SB-101C Maximum Distance ~ 6 feet (2 meters)
SB-101C
IR Tx
SB-101 IR Transmitter Set
Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug
(aka: stereo plug). Using a 2-conductor plug will short out the power supply. Always make connections with the
switcher
p
ower off.
*** When you plug the External IR extender into the switcher, the front panel IR transmitter remains active. ***
IR Transmitter cable 6ft (2M)
SB-101C Transmitter Cable
2. SB-101C IR 2M Transmitter Device Cable (3C) IR Transmitter (SB-101C)
VCC (Ring)
Signal (center)
GND (Sleeve)
Tip Ring
Sleeve
Tip: Signal
Ring :VCC
Sleeve: GND
Ring
Tip (center)
Sleeve
Signal (center)
GND (Sleeve)
Tip Ring
Sleeve
Tip: Signal
Ring: NC
Sleeve: GND
Ring
Tip (center)
Sleeve

8
LIMITED WARRANTY
PLEASE READ THE FOLLOWINGTERMSAND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTSAND SOFTWARE PROVIDED
BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your
agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA,
Inc. at the return address set forth on the Product’s packing label at your expense. SHINYBOWUSA, Inc. may modify these Terms and Conditions at anytime,
without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any
warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be
borne by you and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to the Product
arelicensed toyou bySHINYBOWUSA, Inc.and/or itsaffiliates, includingany manufacturersor distributors of the Product(collectively, “SHINYBOWUSA”)for your
personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use only.
SHINYBOWUSA does not transfer either the title or the intellectual property rights to the Product and SHINYBOWUSA retains full and complete title to the
intellectual property rights therein.All trademarks and logos are owned by SHINYBOWUSAor its licensors and providers of the Product, and you may not copy or
use them in any manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole discretion of SHINYBOWUSA.
ThefunctionalityandusabilityoftheProductiscontrolledbySHINYBOWUSA,Inc.fromitsofficeswithintheStateofTexas,UnitedStatesofAmerica.SHINYBOWUSA
makesnorepresentation that materialspertainingtothe Productareappropriateoravailable foruseinother locations otherthanthe shipping addressyouprovided
with respect thereto. You are advised that the Product may be subject to U.S. export controls.
Disclaimers and Limitation of Liability
SHINYBOWUSAmay change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS”AND WITHOUT WARRANTIES OF ANYKIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSADOES NOT WARRANT
ORMAKEANYREPRESENTATIONSREGARDINGTHEUSEORTHERESULTSOFTHEUSEOFTHEPRODUCT’SCORRECTNESS,ACCURACY,RELIABILITY,
OR OTHERWISE.
SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should
not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical
inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FORA PARTICULAR PURPOSEAND NON-INFRINGEMENT.
SHINYBOWUSADOES NOT WARRANT THEACCURACY, COMPLETENESS OR USEFULNESS OFANY INFORMATION WITH RESPECT TOTHE PRODUCT.
SHINYBOWUSADOESNOTWARRANTTHATTHEFUNCTIONSPERTAININGTOTHEPRODUCTWILLBEERROR-FREE,THATDEFECTSWITHRESPECTTO
THEPRODUCTWILLBECORRECTED, ORTHATTHE MATERIALS PERTAININGTHERETOAREFREE OFDEFECTS OROTHERHARMFULCOMPONENTS.
SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU
NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT SHINYBOWUSA) ASSUME THE ENTIRE COST
OFALL NECESSARY SERVICING, REPAIR AND CORRECTIONTHAT WAS CAUSED BY YOU UNLESS OTHERWISEAGREED TO INASEPARATE WRITING
BY SHINYBOWUSA.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL OR
CONSEQUENTIALDAMAGESTHATRESULTFROMTHEUSEOF,ORTHEINABILITYTOUSETHEPRODUCTINACCORDANCEWITHITSSPECIFICATIONS,
EVEN IF SHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL
SHINYBOWUSA’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE)
EXCEED THEAMOUNT YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT

122 Rose Ln. Suite 303 | Frisco, Texas 75034
1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 [email protected]
MULTIMEDIA AUDIO AND VISUAL
www.shinybowusa.com