Shop fox SHOP FOX D2267 User manual

Dust Collection Nozzle
D2267
Assembly:
1. Threadthe(3)M8-1.25x25Feetintothebottoms
ofthe(3)Legs.
2. Using the (12) M6-1 x 8 Phillips Head Screws,
6mmLockWashers,and6mmFlatWashers,attach
the (3) Legs to the Main Tube Body. Be sure the
LockWashersarebetweentheFlatWashersandthe
PhillipsScrewheadswhentighteneddown.
3. Thread the M8-1.25 x 20 Lock Knob into the
threadedholeonthesideoftheMainTubeBody.
4. Attach the Fixed Support to the top end of the
Silver Main Tube Body using (2) M6-1.0 x 20
PhillipsHeadScrews.
5. ThreadtheM10-1.5HexNutontotheendofthe
M10-1.5 x 15 Lock Knob. Place the end of the
LockKnobandHexBoltassemblythroughtheslot
ontheVacuumTube.Aftertheknobhasbeenslide
through the slot, place the 10mm Flat Washer on
thethreadedendoftheKnob.
6. CarefullythreadtheKnobintothethreadedholein
the Fixed Support. Be sure the Flat Washer is
betweentheFixedSupportandtheVacuumTube.
ThisWasheracts as apivotpointwhen adjusting
the Nozzle position. Tighten the Knob until the
VacuumTuberemainsstationary.
7. SlidetheNozzleintotheendoftheVacuumTube.
TheNozzlecanberotated360°withintheVacuum
Tube. Thread the M6-1 x 15 Lock Knob into the
threadedholeonthetopoftheVacuumTube.This
KnoblockstheNozzleintoposition.
8. Youarenowreadytoenjoydustcollectioninjust
about any location of your shop. If the Stand is
unlevel, thread the Feet in and out until proper
adjustmentisachieved.
If You Need Assistance:
We hope you will find that your Shop Fox® Model
D2267iseasilyassembledandputtouse.Shouldyou
haveany questionsaboutthisproduct,please contact
thedealerwhereyoupurchasedit,oryoucancontact
theWoodstockInternationalTechnicalDepartmentat
1-360-734-3482,MondaythroughFriday,betweenthe
hoursof7:00amto5:00pmPSTore-mailusat:
[email protected]
Wear safety glasses during
the entire assembly
process. Failure to comply
may result in serious
personal injury.
Be sure to read the entire instruction sheet
before beginning the construction of this prod-
uct. Follow every step and use the recommended
tools and supplies. Also, read the instruction
manuals for any tools you are using to complete
this project. Be certain that the tools used for
this installation are intended for the task which
will be performed. Failure to do this could result
in serious personal injury.
TheShopFox®D2267isdesignedtopositionthesuc-
tionofyourdustcollectornearmachinesthatarenot
equipped with dust ports and near other sources of
woodchips.Thenozzleisattachedtoafullyadjustable
stand that permits an endless combination of nozzle
positions.
Tools Needed:
PhillipsScrewdriver
NOTICE
The performance of your Model D2267 will
only be as good as the performance of your
dust collector. Regular maintenance of
your dust collector will ensure maximum
performance from your Model D2267, with-
in the limitations of your dust collector.

COPYRIGHT © APRIL 2002 BY WOODSTOCK INTERNATIONAL, INC. REVISED SEPTEMBER, 2010 (TR)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
www.woodstockinternational.com
433402922
REF PART # DESCRIPTION
1 XD2267001 VACUUM TUBE
2 XD2267002 NOZZLE
3A XD2267003A LOCK KNOB M6-1 X 15
4 XD2267004 FIXED SUPPORT
5A XD2267005A LOCK KNOB M10-1.5 X 15
6A XPW04M FLAT WASHER 10MM
7A XPS26M PHLP HD SCR M6-1 X 20
8A XD2267008A MAIN TUBE BODY
9A XD2267009A LOCK KNOB M8-1.25 X 20
10 XD2267010 SILVER MAIN TUBE BODY
11A XPN02M HEX NUT M10-1.5
12A XPS03M PHLP HD SCR M6-1 X 8
13A XD2267013A LEG
14A XPLW03M LOCK WASHER 6MM
15A XPW03M FLAT WASHER 6MM
16A XD2267016A FOOT M8-1.25 X 25