Shop fox M1117 User manual

OWNER'S MANUAL
(FOR MODELS MANUFACTURED SINCE 9/21)
MODEL M1117
52" SHEET METAL SHEAR
Phone: [phone] • Online Technical Support: [email protected]
COPYRIGHT © SEPTEMBER, 2021 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#22053CS Printed in China
V1.09.21

This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property
damage from negligence, improper training, machine modifications or
misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.

SETUPELECTRICAL MAINTENANCE SERVICE PARTS
OPERATIONS
SAFETYINTRODUCTION
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
INTRODUCTION .....................................2
Woodstock Technical Support .................. 2
Machine Specifications .......................... 3
Identification ..................................... 4
Controls & Components ......................... 5
SAFETY ...............................................6
Standard Machinery Safety Instructions ...... 6
Additional Safety for Metal Shears ............ 8
SETUP ................................................9
Unpacking ......................................... 9
Items Needed for Setup......................... 9
Hardware Recognition Chart ................. 10
Inventory ........................................ 11
Cleaning Machine............................... 12
Machine Placement ............................ 13
Lifting & Placing................................ 14
Anchoring to Floor ............................. 15
Assembly......................................... 16
OPERATIONS....................................... 19
Operation Overview ........................... 19
Cutting Tips ..................................... 20
Adjusting Rear Work Stop..................... 20
Adjusting Front Work Stop.................... 21
Using Bevel Gauge ............................. 21
ACCESSORIES ...................................... 22
Metal Shear Accessories....................... 22
MAINTENANCE .................................... 24
General .......................................... 24
Cleaning & Protecting ......................... 24
Lubrication ...................................... 25
SERVICE ............................................ 27
General .......................................... 27
Adjusting Gibs .................................. 27
Sharpening/Replacing Blade.................. 28
Adjusting Blade Gap ........................... 29
Adjusting Blade Bow........................... 30
Adjusting Return Spring Tension ............. 31
Squaring Front Scales.......................... 31
Adjusting Hold-Down/Blade Guard .......... 32
Troubleshooting................................. 33
PARTS .............................................. 34
Main .............................................. 34
Labels & Cosmetics ............................ 36
WARRANTY ........................................ 37
Contents

-2-
Model M1117 (For Machines Mfd. Since 9/21)
INTRODUCTION
INTRODUCTION
Woodstock Technical Support
This machine has been specially designed to provide many years of trouble-free service. Close attention
to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
We stand behind our machines! In the event that questions arise about your machine, please
contact Woodstock International Technical Support at [phone] Ext. 2 or send e-mail to:
[e-mail]. Our knowledgeable staff will help you troubleshoot problems and pro-
cess warranty claims.
If you need the latest edition, you can download it from http://www.woodstockint.com/manuals.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: [e-mail]

-3-
Model M1117 (For Machines Mfd. Since 9/21)
INTRODUCTION
Model M1117 Machine Specifications, Page 1 of 2
MODEL M1117
52" SHEET METAL SHEAR
Product Dimensions
Weight.......................................................................................................... 982 lbs.
Width (side‐to‐side) x Depth (front‐to‐back) x Height........................................ 62 x 74 x 42 in.
Footprint (Length x Width).............................................................................. 60 x 21 in.
Shipping Dimensions
Type....................................................................................................... Wood Crate
Content........................................................................................................ Machine
Weight........................................................................................................ 1120 lbs.
Length x Width x Height........................................................................... 67 x 30 x 46 in.
Must Ship Upright.................................................................................................. Yes
Main Specifications
Capacities
Maximum Width.......................................................................................... 52 in.
Maximum Thickness Mild Steel.................................................................... 16 Gauge
Maximum Thickness at Half Width Mild Steel................................................... 14 Gauge
Maximum Thickness at Full Width Mild Steel.................................................... 16 Gauge
Aluminum............................................................................................. 12 Gauge
Soft Brass............................................................................................. 14 Gauge
Annealed Phosphor Bronze......................................................................... 17 Gauge
Soft Copper........................................................................................... 14 Gauge
Hard Copper.......................................................................................... 14 Gauge
ABS Plastic............................................................................................... 2.2mm
Stainless Steel........................................................................................ 20 Gauge
Maximum Beam Lift.................................................................................. 1‐3/4 in.
Bed Height Above Floor............................................................................ 42‐1/8 in.
Working Height...................................................................................... 31‐1/4 in.
Front Stop Scale Range........................................................................ 0 ‐ 12‐1/2 in.
Rear Stop Scale Range............................................................................... 0 ‐ 33 in.
Construction
Frame....................................................................................................... Steel
Head and Tail Supports.................................................................................. Steel
Shear Table........................................................................................... Cast Iron
Shear Hold‐Down Clamp............................................................................. Cast Iron
Shear Blades................................................................................. 9CrSi Alloy Steel
Other
Country of Origin ............................................................................................... China
Warranty ....................................................................................................... 2 Years
Approximate Assembly & Setup Time ................................................................. 30 Minutes
Serial Number Location .......................................................................... Machine ID Label

-4-
Model M1117 (For Machines Mfd. Since 9/21)
INTRODUCTION
Become familiar with the names and locations of the controls and features shown below to better
understand the instructions in this manual.
To reduce your risk of serious injury
or damage to the machine, read this
entire manual BEFORE using machine.
Front Extension
Arm (1 of 2)
Bevel Gauge
Front Scale
(1 of 2)
Table
Hold-Down/
Blade Guard
Foot Pedal
Front
Work Stop
Micro-Adjustable
Rear Work Stop
Assembly (1 of 2)
Blade Bow
Rear
Work Stop
Extension
Spring
(1 of 2)
Rear Work Stop
Support Rod
(1 of 2)
Rear Scale
(1 of 2)
USE this and other machinery with caution
and respect. Always consider safety first,
as it applies to your individual working
conditions. No list of safety guidelines can
be complete—every shop environment is
different. Failure to follow guidelines could
result in serious personal injury, damage to
equipment or poor work results.
Identification

-5-
Model M1117 (For Machines Mfd. Since 9/21)
INTRODUCTION
Controls & Components
Refer to the Figures 1-3 and the following descriptions to
become familiar with the basic controls and components
of this machine. Understanding these items and how they
work will help you understand the rest of the manual and
stay safe when operating this machine.
A. Hold-Down/Blade Guard: Holds down workpiece and
protects user from blades during shearing operation.
B. Table: Supports infeed side of workpiece.
C. Bevel Gauge: Secures front edge of angled
workpieces.
D. Foot Pedal: Controls cutting action of upper blade.
E. Front Extension Arm (1 of 2): Provides infeed
support for large workpieces and extends front work
stop and bevel track.
F. Front Work Stop: Adjusts on front extension arms
and holds workpiece in place during shearing
operation.
G. Front Scale (1 of 2): Indicates distance from cutting
line; keeps workpiece square with blades.
H. Rear Work Stop Support Rod (1 of 2): Supports
work stop and has scale for approximate positioning
0-33".
I. Rear Work Stop Indicator: Indicates rear work stop
position on scale.
J. Micro-Adjustment Knob (1 of 2): Fine-tunes rear
work stop position.
K. Rear Work Stop Lock Knob (1 of 2): Loosen to
adjust rear work stop position; tighten to secure.
L. Micro-Adjustment Lock Knob (1 of 2): Loosen to
fine-tune rear work stop position; tighten to secure.
M. Rear Work Stop: Adjusts on rear work stop support
rods to measure workpieces for repeatable cuts.
N. Blade Bow: Adjusts to keep upper blade straight
along its length.
Figure 2. Outfeed components and
controls.
HI
J
KL
M
Figure 1. Infeed components and controls.
C
E
F
G
AB
D
Figure 3. Location of blade bow rod.
N

-6-
Model M1117 (For Machines Mfd. Since 9/21)
SAFETY
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
This symbol is used to alert the user to useful information about
proper operation of the equipment or a situation that may cause
damage to the machinery.
NOTICE
SAFETY
OWNER’S MANUAL.
Read and understand this
owner’s manual BEFORE using machine.
TRAINED OPERATORS ONLY.
Untrained operators
have a higher risk of being hurt or killed. Only
allow trained/supervised people to use this
machine. When machine is not being used,
disconnect power, remove switch keys, or
lock-out machine to prevent unauthorized
use—especially around children. Make
workshop kid proof!
DANGEROUS ENVIRONMENTS.
Do not use
machinery in areas that are wet, cluttered,
or have poor lighting. Operating machinery
in these areas greatly increases the risk of
accidents and injury.
MENTAL ALERTNESS REQUIRED.
Full mental
alertness is required for safe operation of
machinery. Never operate under the influence
of drugs or alcohol, when tired, or when
distracted.
ELECTRICAL EQUIPMENT INJURY RISKS. You can
be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow an
electrician or qualified service personnel to
do electrical installation or repair work, and
always disconnect power before accessing or
exposing electrical equipment.
DISCONNECT POWER FIRST. Always disconnect
machine from power supply BEFORE making
adjustments, changing tooling, or servicing
machine. This eliminates the risk of injury
from unintended startup or contact with live
electrical components.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating
or observing machinery to reduce the risk of
eye injury or blindness from flying particles.
Everyday eyeglasses are not approved safety
glasses.
Standard Machinery Safety Instructions
For Your Own Safety,
Read Manual Before Operating Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words intended to convey the level of importance of the
safety messages. The progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident prevention mea-
sures—this responsibility is ultimately up to the operator!
SAFETY
Standard Machinery Safety Instructions

-7-
Model M1117 (For Machines Mfd. Since 9/21)
SAFETY
WEARING PROPER APPAREL. Do not wear
clothing, apparel,or jewelry that can become
entangled in moving parts. Always tie back
or cover long hair. Wear non-slip footwear to
avoid accidental slips, which could cause loss
of workpiece control.
HAZARDOUS
DUST. Dust created while using
machinery may cause cancer, birth defects,
or long-term respiratory damage. Be aware of
dust hazards associated with each workpiece
material, and always wear a NIOSH-approved
respirator to reduce your risk.
HEARING PROTECTION.
Always wear hearing
protection when operating or observing
loud machinery. Extended exposure to this
noise without hearing protection can cause
permanent hearing loss.
REMOVE ADJUSTING TOOLS.
Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys,
wrenches, or any other tools on machine.
Always verify removal before starting!
INTENDED USAGE.
Only use machine for its
intended purpose—never make modifications
without prior approval from Woodstock
International. Modifying machine or using
it differently than intended will void the
warranty and may result in malfunction or
mechanical failure that leadsto serious
personal injury or death!
AWKWARD POSITIONS.
Keep proper footing and
balance at all times when operating machine.
Do not overreach! Avoid awkward hand
positions that make workpiece control difficult
or increase the risk of accidental injury.
CHILDREN & BYSTANDERS.
Keep children and
bystanders at a safe distance from the work
area. Stop using machine if they become a
distraction.
GUARDS & COVERS.
Guards and covers reduce
accidental contact with moving parts or flying
debris—make sure they are properly installed,
undamaged, and working correctly.
FORCING MACHINERY. Do not force machine. It
will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury may
occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STABLE MACHINE. Unexpected movement during
operation greatly increases risk of injury or
loss of control. Before starting, verify machine
is stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for
recommended accessories. Using improper
accessories will increase risk of serious injury.
UNATTENDED OPERATION. To reduce the risk
of accidental injury, turn machine OFF and
ensure all moving parts completely stop
before walking away. Never leave machine
running while unattended.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to
keep machine in good working condition. A
machine that is improperly maintained could
malfunction, leading to serious personal injury
or death.
CHECK DAMAGED PARTS. Regularly inspect
machine for any condition that may affect
safe operation. Immediately repair or replace
damaged or mis-adjusted parts before
operating machine.
MAINTAIN POWER CORDS. When disconnecting
cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the
cord may damage the wires inside, resulting
in a short. Do not handle cord/plug with wet
hands. Avoid cord damage by keeping it away
from heated surfaces, high traffic areas, harsh
chemicals, and wet/damp locations.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the
intended operation, stop using the machine!
Contact Technical Support at [phone].

-8-
Model M1117 (For Machines Mfd. Since 9/21)
SAFETY
Additional Safety for Metal Shears
FINGER AMPUTATION.
The shear blades or hold-
down can easily pinch, crush, or amputate
fingers or other body parts. Always keep
hands, fingers, and other body parts away
from blades and hold-down (point-of-operation)
during shearing operations.
C APACI T Y.
Exceeding cutting capacity of shear
may result in breakage or machine damage
that ejects dangerous metal debris at operator
or bystanders. Only use sheet metal within
the rated capacity of this shear (refer to the
Machine Specifications).
BLADE CONDITION.
Sharp, undamaged, and
properly adjusted blades will reduce risk
of injury from breakage or sharp burrs left
on workpiece. Always keep blades properly
adjusted and sharp.
SHEAR BLADE ADJUSTMENT.
When adjusting
or replacing shear blades, always wear heavy
leather gloves to protect hands and wear safety
glasses to protect eyes.
PROPER WORKPIECE MATERIAL.
Shear is only
intended for cutting ferrous and non-ferrous
mild sheet metal or flat stock. Do not attempt
to cut round metal stock, glass, wood, drywall,
backer board, plywood, or other material not
intended for this machine. Cutting incorrect
materials can produce unexpected results,
which increases risk of injury, and may result
in damage to machine.
WORK AREA
.Provide sufficient clearance
around machine to permit safe use by regular
operators and performance of maintenance
procedures. Keep work area clear of materials
or substances that may create a slip, trip, or
fall hazard.
SHARP METAL EDGES. The sharp metal edges of
sheet metal can easily cut fingers, hands, and
other body parts. Always wear heavy leather
gloves when handling sheet metal. Always
chamfer and deburr sharp metal workpiece
edges.
OPERATOR POSITION. Avoid awkward body and
hand positions where a sudden slip could cause
your hand or body to enter point-of-operation
or make accidental contact with shear blades.
MAINTENANCE/SERVICE. Always wait for all
moving parts to come to a complete stop
before performing any adjustments, service, or
maintenance. Do not contact foot pedal while
performing these adjustments.
GUARDS.Keep all guards in place, properly
positioned, and in working order. Never
operate shear with blade guard removed.
If blade guard is removed or not properly
positioned, fingers may accidentally be cut or
amputated by shear blades. Always position
guard just high enough to allow workpiece to
enter, but not high enough for fingers.
CHECK MACHINE.
Before using machine, carefully
check components for wear that could affect
operation. Check blade alignment and gib
play, and ensure guards are properly installed.
DO NOT operate machine until all defects are
corrected.
STRAY SHEET METAL PIECES.
Sheet metal cut-off
pieces left on the floor can easily slide under
foot and cause falling injuries. Always remove
cut-off sheet metal pieces from the floor after
operation. Keep work area clean.
Serious cuts, amputation, or death can occur from contact with shear blades during operation,
adjustment, or maintenance. To reduce this risk, anyone using this machine MUST completely
heed the hazards and warnings below.

-9-
Model M1117 (For Machines Mfd. Since 9/21)
SETUP
SETUP
Unpacking
This machine has been carefully packaged for safe
transportation. If you notice the machine has been
damaged during shipping, please contact your authorized
Shop Fox dealer immediately.
Description Qty
• Safety Glasses for Each Person......................1 Pr.
• Disposable Rags ................................ As Needed
• Disposable Gloves ............................. As Needed
• Cleaner/Degreaser ............................ As Needed
• Lifting Equipment (Rated for 1500 lbs.) ...............1
• Another Person.............................................1
• Floor Mounting Hardware .................... As Needed
• Precision Level .............................................1
• Wrench or Socket 10, 12mm........................1 Ea.
• Tape Measure...............................................1
Items Needed for Setup
The following items are needed, but not included, to set
up your machine.
Wear safety glasses during
entire setup process!
This machine presents
serious injury hazards
to untrained users. Read
through this entire manual
to become familiar with
the controls and opera-
tions before starting the
machine!
HEAVY LIFT!
Straining or crushing
injury may occur from
improperly lifting the
machine or some of its
parts. To reduce this
risk, get help from other
people and use a forklift
(or other lifting equip-
ment) rated for weight of
machine.

-10-
Model M1117 (For Machines Mfd. Since 9/21)
SETUP
Hex
Wrench
16mm
MEASURE BOLT DIAMETER BY PLACING INSIDE CIRCLE
7
⁄16"
3⁄8"
1⁄4"
5⁄16"
#10
1⁄2"
WASHERS ARE MEASURED BY THE INSIDE DIAMETER
USE THIS CHART TO IDENTIFY
HARDWARE DURING THE
INVENTORY/ASSEMBLY
PROCESS.
Flat Washer
Lock
Washer
Hex
Nut
Wing
Nut
Set
Screw
Cap
Screw
Carriage
Bolt
Hex
Bolt
Button
Head
Screw
Flange
Bolt
LINES ARE 1⁄16" INCH APART
1⁄4"
3⁄8"
1⁄2"
5⁄8"
5⁄16"
7
⁄16"
9⁄16"
3⁄4"
7
⁄8"
3
21⁄4"
21⁄2"
23⁄4"
2
13⁄4"
11⁄2"
11⁄4"
1
LINES ARE 1MM APART
5mm
10mm
20mm
15mm
25mm
40mm
30mm
35mm
45mm
50mm
60mm
55mm
70mm
65mm
75mm
W
A
S
H
E
R
D
I
A
M
E
T
E
R
5⁄8"
W
A
S
H
E
R
D
I
A
M
E
T
E
R
9⁄16" 1⁄2"
W
A
S
H
E
R
D
I
A
M
E
T
E
R
W
A
S
H
E
R
D
I
A
M
E
T
E
R
12mm
W
A
S
H
E
R
D
I
A
M
E
T
E
R
10mm
7
⁄16"
W
A
S
H
E
R
D
I
A
M
E
T
E
R
W
A
S
H
E
R
D
I
A
M
E
T
E
R
8mm
3⁄8"
W
A
S
H
E
R
D
I
A
M
E
T
E
R
5⁄16"
W
A
S
H
E
R
D
I
A
M
E
T
E
R
1⁄4"
W
A
S
H
E
R
D
I
A
M
E
T
E
R
#10
W
A
S
H
E
R
D
I
A
M
E
T
E
R
W
A
S
H
E
R
D
I
A
M
E
T
E
R
4mm
W
A
S
H
E
R
D
I
A
M
E
T
E
R
6mm
W
A
S
H
E
R
D
I
A
M
E
T
E
R
5mm
4mm
6mm
5mm
8mm
10mm
12mm
Tap
Screw
Phillips
Head
Screw
Flat
Head
Screw
E-Clip
External
Retaining
Ring
Internal
Retaining
Ring
Key
Lock
Nut
Hardware Recognition Chart

-11-
Model M1117 (For Machines Mfd. Since 9/21)
SETUP
Loose Inventory (Figure 4): Qty
A. Front Extension Arms .....................................2
B. Rear Work Stop Support Rods............................2
C. Front Work Stop ...........................................1
D. Rear Work Stop Assemblies ..............................2
E. Rear Work Stop ............................................1
F. Bevel Gauge ................................................1
Inventory
Figure 4. Loose inventory.
Figure 5. Fasteners.
A
B
C
D
E
F
H
O
I
JK
LM
N
G
Fasteners (Figure 5): Qty
G. T-Bolts M12-1.75 x 45 .....................................3
H. Hex Bolts M12-1.75 x 30..................................4
I. Hex Bolts M10-1.5 x 20 ...................................2
J. Flat Washers 12mm .......................................7
K. Flat Washers 10mm .......................................2
L. Wing Nuts M12-1.75 .......................................3
M. Cotter Pins M3 x 50 .......................................4
N. Clevis Pins 12 x 45mm ....................................4
O. Clevis Pins 12 x 88mm ....................................2
The following is a list of items shipped with your machine.
Before beginning setup, lay these items out and inventory
them.
Note: If you cannot find an item on this list, carefully
check around/inside the machine and packaging materials.
Often, these items get lost in packaging materials while
unpacking or they are pre-installed at the factory.

-12-
Model M1117 (For Machines Mfd. Since 9/21)
SETUP
To prevent
corrosion during shipment and storage of your
machine, the factory has coated t
he bare metal surfaces
of your machine
with a heavy-duty rust prevention
compound
.
I
f you are unprepared or impatient, this compound can
be difficult to
remove. To ensure that the removal of this
coating is as easy as possible, please gather the correct
cleaner, lubricant, and tools listed below:
• Cleaner/degreaser
designed to remove storage wax
and grease
• Safety glasses & disposable gloves
•
Solvent brush or paint brush
• Disposable Rags
To
remove rust preventative coating, do these steps:
1.
DISCONNECT MACHINE FROM POWER!
2.
Put on safety glasses and disposable gloves.
3
.Coat the rust preventative with a liberal amount of
cleaner/degreaser, then let it soak for 5–10 minutes.
4
.Wipe off surfaces. If your cleaner/degreaser is
effective, the coating will wipe off easily.
Tip: An easier way to clean off thick coats of rust
preventative from flat surfaces is to use a PLASTIC
paint scraper to scrape off the majority of the
coating before wiping it off with your rag. (Do
not use a metal scraper or you may scratch your
machine.)
5
.Repeat cleaning steps as necessary until all of the
compound is removed.
6
.To prevent rust on freshly cleaned surfaces,
immediately coat with a quality metal protectant.
Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. Avoid
using these products
to clean machinery.
Many cleaning solvents
are toxic if inhaled.
Minimize your risk
by only using these
products in a well
ventilated area.
In a pinch, automotive degreasers,
mineral spirits or WD•40 can be used
to remove rust preventative coating.
Before using these products, though,
test them on an inconspicuous area of
your paint to make sure they will not
damage it.
Cleaning Machine

-13-
Model M1117 (For Machines Mfd. Since 9/21)
SETUP
Figure 6. Minimum working clearances.
Machine Placement
Physical Environment
The physical environment where the machine
is operated is important for safe operation
and longevity of components. For best results,
operate this machine in a dry environment
that is free from excessive moisture, hazardous
chemicals, airborne abrasives, or extreme
conditions. Extreme conditions for this type
of machinery are generally those where the
ambient temperature range is outside 41°–104°F;
the relative humidity range is outside 20–95%
(non-condensing); or the environment is subject
to vibration, shocks, or bumps.
Space Allocation
Consider the largest size of workpiece that
will be processed through this machine and
provide enough space around the machine
for adequate operator material handling or
the installation of auxiliary equipment. With
permanent installations, leave enough space
around the machine to open or remove doors/
covers as required by the maintenance and
service described in this manual.
See below for
required space allocation.
Weight Load
Refer to the Machine Specifications for the
weight of your machine. Make sure that the
surface upon which the machine is placed will
bear the weight of the machine, additional
equipment that may be installed on the
machine, and the heaviest workpiece that will
be used. Additionally, consider the weight of
the operator and any dynamic loading that may
occur when operating the machine.
Lighting
Lighting around the machine must be adequate
enough that operations can be performed
safely. Shadows, glare, or strobe effects that
may distract or impede the operator must be
eliminated.
Children or untrained people
may be seriously injured by this
machine. Only install in an access
restricted location.
Keep Area
Unobstructed
Keep Area
Unobstructed 62"
74"

-14-
Model M1117 (For Machines Mfd. Since 9/21)
SETUP
Lifting & Moving
HEAVY LIFT!
Straining or crushing
injury may occur from
improperly lifting the
machine or some of its
parts. To reduce this
risk, get help from other
people and use a forklift
(or other lifting equip-
ment) rated for weight of
machine.
Use a forklift (or other type of lifting equipment) with
lifting straps to move the machine to your desired
location. All lifting equipment should be rated for at least
1500 pounds.
To lift and move machine, do these steps:
1. Place shipping crate near installation location, then
remove crate top and sides and set small items
aside.
2. Unbolt machine from shipping pallet.
Figure 7. Example of lifting straps placed
under shear table for lifting.
3. Place lifting straps under shear table at locations
shown in Figure 7. Straps should be spread as wide
as possible.
4. With help of another person to steady load, use
forklift or crane to lift machine from pallet and
move to desired location.

-15-
Model M1117 (For Machines Mfd. Since 9/21)
SETUP
Anchoring to Floor
Machine Base
Concrete
Lag Screw
Lag Shield Anchor
Flat Washer
Drilled Hole
Figure 8. Popular method for anchoring
machinery to a concrete floor.
Number of Mounting Holes .................................. 4
Diameter of Mounting Hardware ........................5⁄8"
Anchoring machinery to the floor prevents tipping or
shifting and reduces vibration that may occur during
operation, resulting in a machine that runs slightly quieter
and feels more solid.
If the machine will be installed in a commercial or
workplace setting, or if it is permanently connected
(hardwired) to the power supply, local codes may require
that it be anchored to the floor.
If not required by any local codes, fastening the machine
to the floor is an optional step. If you choose not to do
this with your machine, we recommend placing it on
machine mounts, as these provide an easy method for
leveling and they have vibration-absorbing pads.
Anchoring to Concrete Floors
Lag shield anchors with lag screws (see Figure) are a
popular way to anchor machinery to a concrete floor,
because the anchors sit flush with the floor surface,
making it easy to unbolt and move the machine later, if
needed. However, anytime local codes apply, you MUST
follow the anchoring methodology specified by the code.

-16-
Model M1117 (For Machines Mfd. Since 9/21)
SETUP
Assembly
Figure 11. Extension arm correctly
installed.
Before beginning the assembly process, refer to Items
Needed for Setup
and gather everything you need.
Ensure all parts have been properly cleaned of any
heavy-duty rust-preventative applied at the factory (if
applicable). Be sure to complete all steps in the assembly
procedure prior to performing the
Test Run
or connecting
the machine to power.
To assemble machine, do these steps:
1. Use level to check shear table.
— If table is level, no adjustment is required. Proceed
to Step 2.
— If table is not level, use shims between floor and
base to level machine before proceeding. Leveling
shear helps blades and other components remain
straight and flat during life of machine so machine
can continue to cut straight and square.
2. Cut cable ties securing foot pedal to table.
3. Have another person press and hold foot pedal about
halfway through full range of movement.
4. Insert (2) 12 x 45mm clevis pins in holes in foot
pedal frame and secure with (2) M3 x 50 cotter pins,
as shown in Figure 9.
Figure 9. Location of hole in foot pedal
frame (1 of 2 shown).
x 2
5. Attach (2) front extension arms to shear table with
(4) M12-1.75 x 30 hex bolts and 12mm flat washers
(see Figure 10).
Note: Arm T-slots must line up with table T-slots,
and surfaces must be flush (see Figure 11).
Figure 10. Front extension arms attached
to shear table.
Front
Extension Arm
(1 of 2) x 4

-17-
Model M1117 (For Machines Mfd. Since 9/21)
SETUP
6. Install (1) M12-1.75 x 45 T-bolt in each T-slot and
secure front work stop to extension arms using (2)
12mm flat washers and M12-1.75 wing nuts (see
Figure 12).
Figure 12. Front work stop secured to
extension arms.
Extension Arm
(1 of 2)
Front
Work Stop
x 2
7. Insert (2) rear work stop support rods in holes shown
in Figure 13.
8. Secure rear work stop support rods in place by
tightening pre-installed hex bolts (see Figure 13).
Note: Rear work stop support rods should extend
same distance from back of machine. If one rod
extends farther than the other, adjust hex bolts and
rods until even.
9. Install (2) rear work stop assemblies onto rear work
stop support rods and tighten each micro-adjustment
knob completely to eliminate space shown
in Figure 14.
Figure 13. Rear work stop support rod
installed on machine.
Hex Bolt
Rear Work
Stop Support
Rod (1 of 2)
Figure 14. Rear work stop assembly
installed on rear work stop support rod.
Micro-Adjustment Knob
Rear Work Stop
Assembly
Eliminate This
Space

-18-
Model M1117 (For Machines Mfd. Since 9/21)
SETUP
10. Align each work stop indicator to the same number
on rear work stop support rod scales, then tighten
micro-adjustment lock knobs and rear work stop lock
knobs (see Figure 15).
Figure 15. Rear work stop assembly
components.
11. Attach rear work stop to rear work stop assemblies
with (2) M10-1.5 x 20 hex bolts and 10mm flat
washers, as shown in Figure 16.
Figure 16. Rear work stop attached to
rear work stop assembly.
Work Stop
Indicator
Micro-Adjustment
Lock Knob
Rear Work Stop
Lock Knob
x 2
Rear
Work
Stop
Rear Work
Stop Assembly