Show Tec Airstrike V2 User manual

Airstrike V2
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 43158
MANUAL
ENGLISH

1
Ordercode: 43158
Airstrike
Table of contents
Warning ...............................................................................................................................................................................2
Safety Instructions .........................................................................................................................................................2
Operating Determinations ..........................................................................................................................................4
Rigging ............................................................................................................................................................................4
Connection with the mains.........................................................................................................................................5
Return Procedure..........................................................................................................................................................5
Claims..............................................................................................................................................................................5
Description of the device.................................................................................................................................................6
Features ..........................................................................................................................................................................6
Frontside..........................................................................................................................................................................6
Backside .........................................................................................................................................................................7
Installation...........................................................................................................................................................................7
Installing the Lamp........................................................................................................................................................8
Set Up and Operation .......................................................................................................................................................8
Control Modes...............................................................................................................................................................9
One Airstrike (Auto run mode and Sound-controlled mode) ...........................................................................9
One Airstrike (Manual Mode) ..................................................................................................................................9
Multiple Airstrikes (Master / Slave Control)............................................................................................................9
Multiple Airstrikes (DMX Control) ...........................................................................................................................10
Fixture Linking...............................................................................................................................................................11
Data Cabling...............................................................................................................................................................11
Control Panel ...............................................................................................................................................................12
Control Mode ..............................................................................................................................................................12
DMX Addressing ..........................................................................................................................................................12
Menu Overview...........................................................................................................................................................13
Main Menu Options....................................................................................................................................................14
1. Startup/Auto run mode ......................................................................................................................................14
2. DMX-512 mode ....................................................................................................................................................14
3. Sound options.......................................................................................................................................................14
4. Master/Slave mode.............................................................................................................................................15
5. Display options .....................................................................................................................................................15
6. Sound-controlled mode.....................................................................................................................................15
7. Reset.......................................................................................................................................................................15
8. Manual mode ......................................................................................................................................................16
DMX Channels .............................................................................................................................................................16
10 channels ...............................................................................................................................................................16
Maintenance....................................................................................................................................................................19
Replacing the Fuse.....................................................................................................................................................19
Static Gobo wheel and Color wheel ...........................................................................................................................20
Troubleshooting ...............................................................................................................................................................21
Changing the Lamp...................................................................................................................................................21
No Light.........................................................................................................................................................................21
No Response to DMX..................................................................................................................................................21
Product Specification .....................................................................................................................................................23
Dimensions........................................................................................................................................................................24
Notes ..................................................................................................................................................................................25

2
Ordercode: 43158
Airstrike
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
Showtec Airstrike
IEC power cable (1,5 m)
Safety cable
User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving your lifespan expectancy is of a higher priority, place care in providing
for lower operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
be qualified
follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.

3
Ordercode: 43158
Airstrike
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never place any material over the lens.
Never look directly into the light source.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not connect this device to a dimmerpack.
Do not switch the device on and off in short intervals, as this would reduce the device’s life.
Do not touch the device’s housing bare-handed during its operation. Allow the fixture to cool for at
least 5 minutes before handling.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoors, avoid contact with water or other liquids.
Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly
fastened.
Only operate the device after having familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Always keep case closed while operating.
Always allow free air space of at least 50 cm around the unit for ventilation.
Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
If the lens is obviously damaged, it has to be replaced. So that its functions are not impaired, due to
cracks or deep scratches.
If device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
For adult use only. Device must be installed out of the reach of children. Never leave the unit running
unattended.
Never attempt to bypass the thermostatic switch or fuses.
For replacement use fuses of same type and rating only.
The user is responsible for correct positioning and operating of the Airstrike. The manufacturer will not
accept liability for damages caused by the misuse or incorrect installation of this device.
This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
Repairs, servicing and electric connection must be carried out by a qualified technician.
WARRANTY: Till one year after date of purchase.

4
Ordercode: 43158
Airstrike
Operating Determinations
This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
The minimum distance between light-output and the illuminated surface must be bigger than 1
meter.
The maximum ambient temperature ta = 40°C must never be exceeded.
The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
If this device is operated in any other way, than the one described in this manual, the product may
suffer damages and the warranty becomes void.
Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself!
Always let the installation be carried out by an authorized dealer!
Procedure:
If the Airstrike is lowered from the ceiling or high joists, professional trussing systems have to be used.
Use a clamp to mount the Airstrike, with the mounting-bracket, to the trussing system.
The Airstrike must never be fixed swinging freely in the room.
The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety-cable.
When rigging, derigging or servicing the projector, always make sure, that the area below the
installation place is blocked and staying in the area is forbidden.
The Airstrike can be placed on a flat stage floor or be mounted to any kind of truss, with a clamp.
Improper installation can cause serious damage to people and property!

5
Ordercode: 43158
Airstrike
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersal[email protected] and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.

6
Ordercode: 43158
Airstrike
Description of the device
Features
The Showtec Airstrike is a light fixture with high output and great effects.
Input voltage: 100-240V AC, 60/50Hz
Power consumption: 265W
Light source: Philips MSD 5R lamp
DMX modes: 10 channels
MIrrors: 4 mirrors
Mirror angle: 60°
Color wheel: 7 colors + white
Gobo wheel: 14 metal gobos + open
DMX-control via standard DMX-controller
Onboard: LED display for easy setup
Control modes: Auto run, Manual mode, Sound-controlled, Master/Slave, DMX-512
Dimmer: 0-100%
Strobe: 1-5 Hz
Housing: Die-cast aluminum
Power connector: IEC power connector
Data connectors: 3-pin XLR IN, 3-pin XLR OUT
IP rating: IP20
Cooling: Cooling fan
Spare Lamp 5R ordercode 80988 / 81013
Fuse: F5AL/250V
Dimensions: 300 x 285 x 340 mm (LxWxH)
Weight: 9,4 kg
Frontside
Fig. 01
01) Mounting bracket with inclination screw
02) Adjustment screw
03) Mirror

7
Ordercode: 43158
Airstrike
Backside
Fig. 02
04) LED display + menu buttons
05) Built-in microphone
06) 3-pin DMX signal connector IN
07) 3-pin DMX signal connector OUT
08) IEC power connector 100-240V AC + fuse F5AL/250V
09) Power switch ON/OFF
10) Ground/earth connection
11) Air intake grill
Installation
Remove all packing materials from the Airstrike. Check if all foam and plastic padding is removed.
Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.

8
Ordercode: 43158
Airstrike
Installing the Lamp
The Showtec Airstrike uses the 5R (ordercode 80988 / 81013) reflectorbulb as manufactured by all popular
manufacturers. Use only the appropriate lamp for your unit.
Note that, product versions that use other lamps, may be offered in the future. Check your product
specification label for information.
Always disconnect from electric mains power supply before changing lamps.
The lamp has to be replaced when it is damaged or deformed due to the heat.
Do not install lamps with a higher wattage! Lamps with a higher wattage generate temperatures the
device was not designed for.
Damages caused by non-observance are not subject to warranty.
Procedure:
01) Loosen the 4 screws on the back of the housing.
02) Gently remove the small metal housing.
03) Read lamp instructions. Do not touch the lamp bulb glass. (See Figure 3.). Oil on hands shortens the
lamp life. (If you touch the bulb glass, wipe off the glass with a clean, lint-free towel and rubbing
alcohol.).
04) Insert the lamp into the lamp socket.
05) Put the lamp cover back and fasten the screws snugly.
Fig. 03
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.

9
Ordercode: 43158
Airstrike
Control Modes
There are 5 modes:
Auto run mode
Manual mode
Sound-controlled mode
Master / Slave
DMX-512 (10CH)
One Airstrike (Auto run mode and Sound-controlled mode)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Airstrike is not connected with a DMX cable, it functions as a stand-alone device.
05) Please see page 14-15 for more information.
One Airstrike (Manual Mode)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Airstrike is not connected with a DMX-cable, it functions as a stand-alone device.
05) Please see page 16 for more information about the Manual mode.
Multiple Airstrikes (Master / Slave Control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Airstrikes.
The pins:
01) Earth
02) Signal (-)
03) Signal (+)
05) Link the units as shown in (fig.04). Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units. This means
that you can set your desired operation mode on the master device and all slave devices will react
the same as the master device.
Multiple Airstrikes (Master / Slave Set Up)
Fig. 04

10
Ordercode: 43158
Airstrike
Multiple Airstrikes (DMX Control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Airstrikes and other devices.
05) Link the units as shown in (fig.05). Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units.
06) Supply electric power: Plug electric mains power cords into each unit's IEC socket, then plug the
other end of the mains power cord into proper electric power supply sockets, starting with the first
unit. Do not supply power before the whole system is set up and connected properly.
Multiple Airstrikes (DMX Set Up)
Fig. 05

11
Ordercode: 43158
Airstrike
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows on two or more fixtures set to a master / slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy chained in one single line. To comply with the
EIA-485 standard no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of Airstrikes on a DMX data link: 30 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin. Ordercode
FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m), FLX01150
(1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m), FL09150 (1,5
m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).

12
Ordercode: 43158
Airstrike
The Airstrike can be operated with a controller in control mode or without the controller in stand-alone
mode.
Control Panel
A)
B)
C)
D)
E)
LED display
MENU button
UP button
DOWN button
ENTER button
Fig. 06
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller.
DMX Addressing
The control panel on the front side of the base allows you to assign the DMX fixture address, which is the
first channel from which the Airstrike will respond to the controller.
Please note when you use the controller, the unit has 10 channels.
When using multiple Airstrikes make sure you set the DMX addresses right.
Therefore, the DMX address of the first Airstrike should be 1(001); the DMX address of the second Airstrike
should be 1+10=17 (011); the DMX address of the third Airstrike should be 11+10=21 (021), etc.
Please, be sure that you do not have any overlapping channels in order to control each Airstrike
correctly.
If two or more Airstrikes are addressed similarly, they will work similarly.
Controlling:
After having addressed all Airstrike fixtures, you may now start operating these via your lighting controller.
Note: After switching on, the Airstrike will automatically detect whether DMX 512 data is received or not. If
there is no data received at the DMX-input, the display text on the control panel will not flash.
The problem may be:
The XLR cable from the controller is not connected with the input of the Airstrike.
The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It’s necessary to insert a XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
Display Off after 10 seconds
When no button is pressed for 10 seconds, the display will turn off.
To light up the display, you have to press the MENU, UP, DOWN or ENTER button.
Once you have pressed the button, the display will light up.

13
Ordercode: 43158
Airstrike
Menu Overview

14
Ordercode: 43158
Airstrike
Main Menu Options
DMX-512 mode
Sound options
Master/Slave mode
Display options
Sound-controlled mode
Reset
Manual mode
1. Startup/Auto run mode
01) Upon startup, the display will show the current operation mode, for example .
02) Meanwhile, the device will perform its automatic show.
03) Press the MENU button to enter the main menu.
2. DMX-512 mode
With this menu you can set the DMX starting address.
01) Press the UP/DOWN buttons until the display shows .
02) Press the ENTER button to open the menu.
03) Press the UP/DOWN buttons to set the desired DMX starting address. The adjustment range is
between .
3. Sound options
With this menu you can set the device’s behavior, while in Sound-controlled mode.
01) Press the UP/DOWN buttons until the display shows .
02) Press the ENTER button to open the menu.
03) Press the UP/DOWN buttons to select one of the 3 functions:
If there is no music, the device will run a built-in program.
If there is no music, the device will black out.
If there is no music, the device will return to the previously active
mode.
04) Press the ENTER button to confirm your choice.
05) If the Sound-controlled mode is switched ON (see page 14), the device will perform one of the 3
actions described above.

15
Ordercode: 43158
Airstrike
4. Master/Slave mode
With this menu you can set the device as a master or a slave device.
01) Press the UP/DOWN buttons until the display shows .
02) Press the ENTER button to open the menu.
03) Press the UP/DOWN buttons to choose one of the 2 options: (master) or (slave).
04) If you have chosen , the device will be classified as a master device.
05) If you have chosen , the device will be classified as a slave device and will act the same as
the master device.
06) Press the ENTER button to confirm your choice.
5. Display options
With this menu you can set the display options.
01) Press the UP/DOWN buttons until the display shows .
02) Press the ENTER button to open the menu.
03) Press the UP/DOWN buttons to choose between ON and OFF.
04) If you have chosen ON, the display will remain continuously on.
05) If you have chosen OFF, the display will turn off if no button is pressed within 10 seconds.
06) Press the ENTER button to confirm your choice.
6. Sound-controlled mode
With this menu you can set Sound-controlled mode.
01) Press the UP/DOWN buttons until the display shows .
02) Press the ENTER button to open the menu.
03) Press the UP/DOWN buttons to choose between ON and OFF.
04) If you have chosen ON, the device will react to the beat of the background music.
05) Press the ENTER button to confirm your choice.
7. Reset
With this menu you can reset the device’s settings.
01) Press the UP/DOWN buttons until the display shows .
02) Press the ENTER button to open the menu.
03) Press the UP/DOWN buttons to choose between YES and NO.
04) If you have chosen YES, press the ENTER button to confirm. The device will now reset the settings.
05) If you have chosen NO, press the ENTER button to confirm. The device will return to the main menu.

16
Ordercode: 43158
Airstrike
8. Manual mode
With this menu you can set Manual mode.
01) Press the UP/DOWN buttons until the display shows .
02) Press the ENTER button to open the menu.
03) Press the UP/DOWN buttons to choose between ON and OFF.
04) If you have chosen ON, press the ENTER button to confirm.
05) Now, while in the main menu, press the UP/DOWN buttons until the display shows one of the 10 DMX
channels.
06) Press the ENTER button to edit the desired channel.
07) Press the UP/DOWN button to set the value of the desired channel. The adjustment range for each
channel is between .
08) Press the ENTER button to save changes.
09) See below for the available DMX channels and their functions.
DMX Channels
10 channels
Channel 1 –Shutter/Strobe Dimmer must be open and CH10 must be set between 151-200
0-10
Shutter closed
11-39
Shutter open
40-240
Strobe effect, from slow to fast
241-255
Shutter open
Channel 2 –Dimmer
0-255
Gradual dimmer adjustment, from dark to brightest
Channel 3 –Colors Dimmer and shutter must be open and CH10 must be set between 151-200
0-15
White
16-31
Red
32-47
Green
48-63
Blue
64-79
Amber
80-95
Yellow
96-111
Magenta
112-127
Pink
128-191
Counterclockwise rotation, from fast to slow
192-255
Clockwise rotation, from slow to fast

17
Ordercode: 43158
Airstrike
Channel 4 –Static Gobo CH1 and CH2 must be open and CH10 must be set between 151-200
0-4
Open
5-9
Gobo 1
10-14
Gobo 2
15-19
Gobo 3
20-24
Gobo 4
25-29
Gobo 5
30-34
Gobo 6
35-39
Gobo 7
40-44
Gobo 8
45-49
Gobo 9
50-54
Gobo 10
55-59
Gobo 11
60-64
Gobo 12
65-69
Gobo 13
70-74
Gobo 14
75
Gobo rotation at the highest speed
76-81
Gobo 1 shake effect, from slow to fast
82-87
Gobo 2 shake effect, from slow to fast
88-93
Gobo 3 shake effect, from slow to fast
94-99
Gobo 4 shake effect, from slow to fast
100-105
Gobo 5 shake effect, from slow to fast
106-111
Gobo 6 shake effect, from slow to fast
112-117
Gobo 7 shake effect, from slow to fast
118-123
Gobo 8 shake effect, from slow to fast
124-129
Gobo 9 shake effect, from slow to fast
130-135
Gobo 10 shake effect, from slow to fast
136-141
Gobo 11 shake effect, from slow to fast
142-147
Gobo 12 shake effect, from slow to fast
148-153
Gobo 13 shake effect, from slow to fast
154-158
Gobo 14 shake effect, from slow to fast
159-207
Clockwise rotation, from fast to slow
208-255
Counterclockwise rotation, from slow to fast
Channel 5 –Roller rotation
0-63
Gradual roller adjustment, 0-360°
64-67
Stop
68-127
Roller shake, from slow to fast
128-132
Stop
133-191
Clockwise roller rotation, from fast to slow
192-196
Stop
197-255
Counterclockwise roller rotation, from slow to fast

18
Ordercode: 43158
Airstrike
Fig. 07
Channel 6 –Mirror 1 Shake
0-127
Gradual mirror angle adjustment
128-159
Mirror shake with the biggest amplitude, from slow to fast
160-191
Mirror shake with the 2nd biggest amplitude, from slow to fast
192-223
Mirror shake with the 3rd biggest amplitude, from slow to fast
224-255
Mirror shake with the 4th biggest amplitude, from slow to fast
Channel 7 –Mirror 2 Shake
0-127
Gradual mirror angle adjustment
128-159
Mirror shake with the biggest amplitude, from slow to fast
160-191
Mirror shake with the 2nd biggest amplitude, from slow to fast
192-223
Mirror shake with the 3rd biggest amplitude, from slow to fast
224-255
Mirror shake with the 4th biggest amplitude, from slow to fast
Channel 8 –Mirror 3 Shake
0-127
Gradual mirror angle adjustment
128-159
Mirror shake with the biggest amplitude, from slow to fast
160-191
Mirror shake with the 2nd biggest amplitude, from slow to fast
192-223
Mirror shake with the 3rd biggest amplitude, from slow to fast
224-255
Mirror shake with the 4th biggest amplitude, from slow to fast
Channel 9 –Mirror 4 Shake
0-127
Gradual mirror angle adjustment
128-159
Mirror shake with the biggest amplitude, from slow to fast
160-191
Mirror shake with the 2nd biggest amplitude, from slow to fast
192-223
Mirror shake with the 3rd biggest amplitude, from slow to fast
224-255
Mirror shake with the 4th biggest amplitude, from slow to fast
Channel 10 –Functions
0-50
Not functional
51-100
Energy saving mode
101-150
Lamp OFF (after 5 seconds)
151-200
Lamp ON (after 5 seconds)
201-225
Auto run
226-230
Reset
231-255
Sound-controlled

19
Ordercode: 43158
Airstrike
Maintenance
The Showtec Airstrike requires almost no maintenance. However, you should keep the unit clean.
Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply and
then wipe the cover with a damp cloth. Wipe the front glass panel clean with glass cleaner and a soft
cloth. Do not use alcohol or solvents. The front glass panel will require weekly cleaning, as smoke-fluid
tends to build up residues, reducing the light output very quickly. Do not immerse in liquid.
Keep connections clean. Disconnect electric power, and then wipe the DMX connections with a damp
cloth. Make sure connections are thoroughly dry before linking equipment or supplying electric power.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and must
not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
Replacing the Fuse
Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out.
If the fuse burns out, the product will not function whatsoever. If this happens, follow the directions below:
01) Unplug the unit from electric power source.
02) Insert a flat-headed screwdriver into a slot in the fuse cover. Gently pry up the fuse cover. The fuse
will come out.
03) Remove the used fuse. If brown or unclear, it is burned out.
04) Insert the replacement fuse into the holder. Reinsert the fuse cover. Be sure to use a fuse of the
same type and specification. See the product specification label for details.