Show Tec BB7 User manual

BB7 Beam Bar V1
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 30744
MANUAL
ENGLISH

1
Ordercode: 30744
BB7 Beam Bar
Table of contents
Warning ...............................................................................................................................................................................2
Safety Instructions .........................................................................................................................................................2
Operating Determinations ..........................................................................................................................................4
Rigging ............................................................................................................................................................................4
Connection with the mains.........................................................................................................................................5
Return Procedure..........................................................................................................................................................5
Claims..............................................................................................................................................................................5
Description of the device.................................................................................................................................................6
Frontside..........................................................................................................................................................................6
Backside .........................................................................................................................................................................7
Installation...........................................................................................................................................................................7
Set Up and Operation .......................................................................................................................................................7
Control Modes...............................................................................................................................................................7
One BB7 (Auto Run)...................................................................................................................................................7
One BB7 (Sound-control)..........................................................................................................................................8
Multiple BB7’s (Master/Slave control) ....................................................................................................................8
Multiple BB7’s (DMX512 Mode) ...............................................................................................................................9
Fixture Linking ...............................................................................................................................................................10
Data Cabling...............................................................................................................................................................10
Control Panel ...............................................................................................................................................................11
DMX Control Mode.....................................................................................................................................................11
DMX Addressing ..........................................................................................................................................................11
Menu overview ................................................................................................................................................................12
Main Menu Options....................................................................................................................................................12
1. Auto Mode............................................................................................................................................................13
2. Master/Slave Mode.............................................................................................................................................13
3. Sound Mode .........................................................................................................................................................13
4. Software Information ..........................................................................................................................................13
5. DMX Address ........................................................................................................................................................14
6. DMX Channels......................................................................................................................................................14
DMX Channels .............................................................................................................................................................14
1 DMX Channels.......................................................................................................................................................14
6 DMX Channels.......................................................................................................................................................14
7-PX DMX Channels.................................................................................................................................................15
Maintenance....................................................................................................................................................................16
Troubleshooting ...............................................................................................................................................................16
No Light.........................................................................................................................................................................16
No Response to DMX..................................................................................................................................................17
Product Specifications....................................................................................................................................................18
Dimensions........................................................................................................................................................................19
Notes ..................................................................................................................................................................................20

2
Ordercode: 30744
BB7 Beam Bar
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear to be damaged from shipping or the carton
itself shows signs of mishandling. Save the carton and all packing materials. In the event that the fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box and
packing.
Your shipment includes:
●Showtec BB7 Beam Bar
●Included bracket
●ProPower powercable 1,5m
●User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
●be qualified
●follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty. This device contains no user-serviceable parts. Refer servicing to qualified technicians only.

3
Ordercode: 30744
BB7 Beam Bar
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never place any material over the lens.
Never look directly into the light source.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not connect this device to a dimmerpack.
Do not switch the device on and off in short intervals, as this would reduce the device’s lifespan.
Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Allow the fixture to cool for at least 5 minutes before handling.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoor, avoid contact with water or other liquids.
Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
Only operate the device after having familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Always keep case closed while operating.
Always allow free air space of at least 50 cm around the unit for ventilation.
Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
If the lens is obviously damaged, it has to be replaced to prevent its functions from being impaired,
due to cracks or deep scratches.
If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
For adult use only. Device must be installed out of reach of children. Never leave the unit running
unattended.
Never attempt to bypass the thermostatic switch or fuses.
For replacement, use fuses of same type and rating only.
The user is responsible for correct positioning and operating of the BB7. The manufacturer will not
accept liability for damages caused by the misuse or incorrect installation of this device.
This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
Repairs, servicing and electrical connection must be carried out by a qualified technician.
WARRANTY: Till one year after date of purchase.

4
Ordercode: 30744
BB7 Beam Bar
Operating Determinations
●This device is not designed for permanent operation. Regular operation breaks will ensure that the
device will serve you for a long time without defects.
●The minimum distance between light-output and the illuminated surface must be bigger than 1
meter.
●The maximum ambient temperature ta = 40°C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
●If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
●Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself!
Always let the installation be carried out by an authorized dealer!
Procedure:
●If the BB7 is lowered from the ceiling or high joists, professional trussing systems have to be used.
●Use a clamp to mount the BB7, with the mounting-bracket, to the trussing system.
●The BB7 must never be fixed swinging freely in the room.
●The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety-cable.
●When rigging, derigging or servicing the BB7, always make sure, that the area below the installation
place is blocked and staying in the area is forbidden.
The BB7 Beam Bar can be placed on a flat stage floor or mounted to any kind of truss by a clamp.
Improper installation can cause serious injuries and/or damage of property!

5
Ordercode: 30744
BB7 Beam Bar
Connection with the mains
Connect the device to the mains with the power plug.
Always check if the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE
GROUND
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause of the
return. Be sure to properly pack fixture as any shipping damage resulting from inadequate packaging is
the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that the fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period, complaints will not be handled anymore.
Complaints will only be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.

6
Ordercode: 30744
BB7 Beam Bar
Description of the device
Features
The BB7 Beam Bar is a LED bar from Showtec. It is ideal to use as a light curtain, audience blinder or
background effect.
•Compact size
•Input voltage: 100-240V, 50/60Hz
•Power consumption: 30W
•Light source: 7x3W (CREE LEDs)
•Color temperature: 3200K
•Drive current: 630mA
•Refresh rate: 2,2KHz
•Pixels: 1x7
•Pixelpitch: 60mm
•Field angle: 4º
•LCD Display for easy setup
•Control Mode: Auto, Sound, Master/Slave, DMX512
•Control protocol: DMX-512
•DMX channels: 1, 6, 7 channels
•Dimmer: 0-100%
•Strobe: 0-25Hz
•Connections: 3-pin XLR data IN/OUT, ProPower IN/OUT
•Housing: black powder coated metal
•IP rating: IP-20
•Dimensions: 500 x 105 x 130 mm (LxWxH) (incl. bracket)
•Weight: 2,5 kg
Note: Knowledge of DMX is required to fully utilize this unit.
Frontside
Fig. 01
01) Adjustment screws + mounting bracket for Truss mounting
02) 7x3W (CREE LEDs)

7
Ordercode: 30744
BB7 Beam Bar
Backside
Fig. 02
03) ProPower connector blue IN
04) Power Switch On/Off
05) Ground/Earth connection
06) Menu Buttons + LCD display
07) DMX LED indicator
08) DMX signal connector (IN) 3-pin
09) DMX signal connector (OUT) 3-pin
10) Safety eye
11) ProPower connector grey OUT
Installation
Remove all packing materials from the BB7 Beam Bar.
Check that all foam and plastic padding is removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply.
Control Modes
There are 4 modes:
Auto Run
Sound-controlled
Master/Slave
DMX512 (1CH, 6CH, 7CH)
One BB7 (Auto Run)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the BB7 is not connected with a DMX cable, it functions as a stand-alone device.
05) Please see page 13 for more information about auto–run programs.

8
Ordercode: 30744
BB7 Beam Bar
One BB7 (Sound-control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Turn on the music. If device is set to sound-control, then the fixture will react to the beat of the
music. Please see page 13 for more information about the Sound-control options.
Multiple BB7’s (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-p XLR cable to connect the BB7 and other devices.
The pins:
1. Earth
2. Signal (-)
3. Signal (+)
05) Link the units as shown in Fig. 03, connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second and third units. You can use the
same functions on the master device as described on page 13 (Auto run, Sound control). This means
you can set your desired operation mode on the master device and all slave devices will react the
same as the master device.
Multiple BB7’s (Master/Slave control)
Fig.03

9
Ordercode: 30744
BB7 Beam Bar
Multiple BB7’s (DMX512 Mode)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-p XLR cable to connect the BB7 and other devices.
05) Link the units as shown in Fig. 04, Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second and third units.
06) Supply electric power: Plug electric mains power cords into each unit's ProPower socket, then plug
the other end of the mains power cord into proper electric power supply sockets, starting with the
first unit. Do not supply power before the whole system is set up and connected properly.
Multiple BB7’s DMX Set Up
Note: Link all cables before connecting electric power!

10
Ordercode: 30744
BB7 Beam Bar
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX
optically isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
•DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin. Ordercode
FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
•DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
•DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
•DAP Audio DMX adapter: 3-pin/5-pin. Ordercode FLA30.
The BB7 Beam Bar can be operated with a controller in control mode or without the controller in stand-
alone mode.

11
Ordercode: 30744
BB7 Beam Bar
Control Panel
A. LCD Display
B. MENU button
C. ENTER Button
D. UP Button
E. DOWN Button
Fig. 05
DMX Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address the next time.)
DMX Addressing
The control panel on the backside of the device allows you to assign the DMX fixture address, which is
the first channel from which the BB7 will respond to the controller. Please note when you use the
controller, the unit has up to 7 channels. When using multiple BB7’s, make sure you set the DMX addresses
right. Therefore, the DMX address of the first BB7 should be 1(001); the DMX address of the second BB7
should be 1+7=8 (008); the DMX address of the third BB7 should be 8+7=15 (015), etc. Please, be sure that
you do not have any overlapping channels in order to control each BB7 correctly. If two or more BB7’s
are addressed similarly, they will work similarly.
Controlling:
After having addressed all BB7’s, you may now start operating these via your lighting controller.
Note: After switching on, the BB7 will automatically detect whether DMX 512 data is received or not. If
there is no data received at the DMX-input, the LED indicator on the backside will not flash. The problem
may be:
•The XLR cable from the controller is not connected with the input of the BB7.
•The controller is switched off or defective, the cable or connector is defective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert a XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
Display Off after 30 seconds
When no button is pressed for 30 seconds, the display will turn off. To light up the display, you have to
press the MENU, ENTER, UP or DOWN button. Once you have pressed the button, the display will light up.

12
Ordercode: 30744
BB7 Beam Bar
Menu overview
The BB7 will show the following screen at start-up !
Main Menu Options
Auto Mode
Master/Slave Mode
Sound Mode
Software information
DMX address
DMX channels

13
Ordercode: 30744
BB7 Beam Bar
1. Auto Mode
With this menu you can set the auto programs.
01) Press the UP/DOWN buttons until the display shows .
02) Press the ENTER button to open the menu.
03) Press the UP/DOWN buttons to toggle between the following 2 options:
Auto mode speed
Auto mode programs
04) When the display shows , press the ENTER button to open the menu.
05) Press the UP/DOWN buttons to increase/decrease the program speed. The adjustment range is
between , from slow to fast.
06) Press the ENTER button to save changes.
07) When the display shows , press the ENTER button to open the menu.
08) Press the UP/DOWN buttons to toggle between the available programs:
.
09) You can choose between 29 programs and Mix (all the built-in programs will be displayed in a
sequence).
10) Press the ENTER button to save changes.
2. Master/Slave Mode
With this menu you can set the device as a slave.
01) Press the UP/DOWN buttons until the display shows .
02) Press the ENTER button to open the menu.
03) Press the UP/DOWN buttons to choose between “YES” or “NO”.
04) If you choose “YES”, the device has been set to slave, it will react the same as its master device.
05) Press the ENTER button to confirm your choice.
3. Sound Mode
With this menu you can set the sensitivity of the sound mode.
01) Press the UP/DOWN buttons until the display shows .
02) Press the ENTER button to open the menu.
03) Press the UP/DOWN buttons to increase/decrease the sensitivity. The adjustment range is between
, from low to high sensitivity.
04) Press the ENTER button to confirm your choice.
05) Turn on the music and the BB7 will react to the beat of the music.
4. Software Information
With this menu you can check the currently installed software version.
01) Press the UP/DOWN buttons until the display shows .
02) Press the ENTER button to open the menu.
03) The display shows the current software version: .

14
Ordercode: 30744
BB7 Beam Bar
5. DMX Address
With this menu you can set the desired DMX address.
01) Press the UP/DOWN buttons until the display shows .
02) Press the ENTER button to open the menu.
03) Press the UP/DOWN buttons to choose the desired DMX address. The adjustment range is between
.
04) Press the ENTER button to save changes.
6. DMX Channels
With this menu, you can set the desired channel mode.
01) Press the UP/DOWN buttons until the display shows .
02) Press the ENTER button to open the menu.
03) Press the UP/DOWN buttons to choose between the 3 DMX channel modes:
1-channel mode
6-channel mode
7-channel mode
04) Press the ENTER button to confirm your choice.
DMX Channels
1 DMX Channels
Channel 1 –White Dimmer intensity
0-255
Gradual adjustment White from 0 –100%
6 DMX Channels
Channel 1 –White Dimmer intensity
0-255
Gradual adjustment White from 0 –100%
Channel 2 –Strobe (CH1 must be between 1-255 and CH3 and CH4 between 0-15 )
0-255
Strobe flash frequency, from slow to fast (0-25 Hz)
Channel 3–Built-in Programs 1 (CH1 must be between 1-255 )
0-15
No function
16-31
Program 01
32-47
Program 02
48-63
Program 03
64-79
Program 04
80-95
Program 05
96-111
Program 06
112-127
Program 07
128-143
Program 08
144-159
Program 09
160-175
Program 10
176-191
Program 11

15
Ordercode: 30744
BB7 Beam Bar
192-207
Program 12
208-223
Program 13
224-239
Program 14
240-255
Program 15
Channel 4 –Built-in Programs 2 (CH1 must be between 1-255 )
0-15
No function
16-31
Program 16
32-47
Program 17
48-63
Program 18
64-79
Program 19
80-95
Program 20
96-111
Program 21
112-127
Program 22
128-143
Program 23
144-159
Program 24
160-175
Program 25
176-191
Program 26
192-207
Program 27
208-223
Program 28
224-239
Program 29
240-255
Sound-controlled
Channel 5- Speed (CH4 must be set between 16-255 or CH5 between 16-239 )
0-255
Gradual adjustment Speed, From slow to fast
Channel 6–Sound sensitivity (CH5 must be set between 240-255 )
0-15
No function
16-255
Gradual adjustment Sensitivity, from 1-100%
7-PX DMX Channels
Channel 1 –White LED Pixel 1
0-255
Gradual adjustment White from 0 –100%
Channel 2 –White LED Pixel 2
0-255
Gradual adjustment White from 0 –100%
Channel 3 –White LED Pixel 3
0-255
Gradual adjustment White from 0 –100%
Channel 4 –White LED Pixel 4
0-255
Gradual adjustment White from 0 –100%

16
Ordercode: 30744
BB7 Beam Bar
Channel 5 –White LED Pixel 5
0-255
Gradual adjustment White from 0 –100%
Channel 6 –White LED Pixel 6
0-255
Gradual adjustment White from 0 –100%
Channel 7 –White LED Pixel 7
0-255
Gradual adjustment White from 0 –100%
Maintenance
The operator has to make sure that safety-relating and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and must
not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
The Showtec BB7 Beam Bar requires almost no maintenance. However, you should keep the unit clean.
Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply and
then wipe the cover with a damp cloth. Wipe the front glass panel clean with glass cleaner and a soft
cloth. Do not use alcohol or solvents. The front glass panel will require weekly cleaning, as smoke-fluid
tends to build up residues, reducing the light-output very quickly. Do not immerse in liquid.
Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections
with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying
electric power.
Troubleshooting
No Light
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, follow the steps below in sequence until a solution is found. Once the unit operates
properly, do not carry out the following steps.
If the light effect does not operate properly, refer servicing to a technician.
Response: Suspect two potential problem areas as the power supply, the LEDs.
01) Power supply. Check that the unit is plugged into an appropriate power supply.
02) The LEDs. Return the BB7 to your Showtec dealer.
03) If all of the above appears to be in order, switch the unit on again.
04) If you are unable to determine the cause of the problem, do not open the BB7, as this may damage
the unit and the warranty will become void.
05) Return the device to your Showtec dealer.

17
Ordercode: 30744
BB7 Beam Bar
No Response to DMX
Response: Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card
malfunction.
01) Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is to blame. Does the controller operate properly with
other DMX products? If not, take the controller in for repair. If it does, take the DMX cable and the
light effect to a qualified technician.
Problem
Probable cause(s)
Solution
One or more
fixtures do not
function at all
No power to the fixture
•Check if power is switched on and
cables are plugged in
Internal fuse blown
•Return the device to your local
Showtec dealer.
Fixtures reset
correctly, but all
respond
erratically or not
at all to the
controller
The controller is not connected.
•Connect controller.
3-pin/5-pin XLR Out of the
controller does not match XLR Out
of the first fixture on the link (i.e.
signal is reversed)
•Install a phase reversing cable
between the controller and the
first fixture on the link
Fixtures reset
correctly, but
some respond
erratically or not
at all to the
controller
Poor data quality
•Check data quality. If much lower
than 100 percent, the problem
may be a bad data link
connection, poor quality or
broken cables, missing termination
plug, or a defective fixture
disturbing the link
Bad data link connection
•Inspect connections and cables.
Correct poor connections. Repair
or replace damaged cables
Data link not terminated with 120
Ohm termination plug
•Insert termination plug in output
jack of the last fixture on the link
Incorrect addressing of the fixtures
•Check address setting
One of the fixtures is defective and
disturbs data transmission on the
link
•Bypass one fixture at a time until
normal operation is restored:
unplug both connectors and
connect them directly together.
•Have the defective fixture
serviced by a qualified technician
3-pin/5-pin XLR Out on the fixtures
does not match (pins 2 and 3
reversed)
•Install a phase-reversing cable
between the fixtures or swap pin 2
and 3 in the fixture that behaves
erratically
No light or LEDs
cuts out
intermittently
Fixture is too hot
•Allow the fixture to cool down
•Make sure air vents in control
panel and the front lens are not
blocked
•Turn up the air conditioning
LEDs damaged
•Disconnect the fixture and return it
to your dealer
The power supply settings do not
match local AC voltage and
frequency
•Disconnect fixture. Check settings
and correct if necessary

18
Ordercode: 30744
BB7 Beam Bar
Product Specifications
Model:
Showtec BB7 Beam Bar
Input Voltage:
100-240V AC, 50/60Hz
Power consumption
30 Watt
DMX linking:
30pcs
Dimensions:
500 x 105 x 130 mm (LxWxH) (incl. bracket)
Weight:
2,5 kg
Operating and Programming:
Signal pin OUT:
Pin 1 (earth), pin 2 (-), pin 3 (+)
DMX Mode:
1, 6 or 7 channels
Signal input:
3-pin XLR male
Signal output:
3-pin XLR female
Electro-mechanical effects:
Light source:
7x3W (CREE LEDs)
Color temperature:
3200K
Drive current:
630mA
Refresh rate:
2,2KHz
Pixels:
1x7
Pixelpitch:
60mm
Field angle:
4º
Dimmer:
0-100%
Strobe:
0-25Hz
Display:
LCD display
Housing:
black powder coated metal
IP rating:
IP-20
DMX-control:
DMX512 via standard DMX-controller
Control:
Auto, Sound, Master/Slave, DMX512
Connections:
3-pin XLR data IN/OUT, ProPower IN/OUT
Max. ambient temperature ta:
40°C
Max. housing temperature tB:
80°C
Minimum distance:
Minimum distance from flammable surfaces:
0,5 m
Minimum distance to lighted object:
1 m
Design and product specifications are subject to change without prior notice
Website: www.Showtec.info
Email: [e-mail]

19
Ordercode: 30744
BB7 Beam Bar
Dimensions