Show Tec Candela Pix 100 User manual

Candela Pix 100 V1
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 41281
MANUAL
ENGLISH

1
Ordercode: 41281
Candela Pix 100
Table of contents
Warning ...............................................................................................................................................................................2
Safety Instructions .........................................................................................................................................................2
Operating Determinations ..........................................................................................................................................4
Rigging ............................................................................................................................................................................4
Connection with the mains.........................................................................................................................................5
Return Procedure..........................................................................................................................................................5
Claims..............................................................................................................................................................................5
Description of the device.................................................................................................................................................6
Overview ........................................................................................................................................................................7
Backside .........................................................................................................................................................................7
Side ..................................................................................................................................................................................7
Installation...........................................................................................................................................................................8
Set Up and Operation .......................................................................................................................................................8
Control Modes...............................................................................................................................................................8
One Candela Pix (Auto program, Built-in programs and Manual control)....................................................8
Multiple Candela Pixs (Master/Slave control) ......................................................................................................8
Multiple Candela Pixs (DMX512 Mode).................................................................................................................9
Fixture Linking ...............................................................................................................................................................10
Data Cabling...............................................................................................................................................................10
Control Panel ...............................................................................................................................................................11
DMX Control Mode.....................................................................................................................................................11
DMX Addressing ..........................................................................................................................................................11
Menu overview ................................................................................................................................................................12
Main Menu Options ....................................................................................................................................................13
1. DMX Address/ DMX Configuration...................................................................................................................13
2. Manual...................................................................................................................................................................14
3. Auto program.......................................................................................................................................................14
4. Built-in programs ..................................................................................................................................................14
5. Master/slave .........................................................................................................................................................15
6. Settings...................................................................................................................................................................15
6.1. Curves Select ....................................................................................................................................................16
6.2. Pixel Invert ..........................................................................................................................................................16
6.3. PWM Frequency ...............................................................................................................................................17
6.4. DMX Fail..............................................................................................................................................................17
6.5. DMX Sync ...........................................................................................................................................................17
6.6. Lock.....................................................................................................................................................................18
6.7. Key Backlight.....................................................................................................................................................18
6.8. Factory................................................................................................................................................................18
7. Information............................................................................................................................................................18
DMX Channels .............................................................................................................................................................19
4 Channels ................................................................................................................................................................19
6 Channels ................................................................................................................................................................19
9 DMX Channels.......................................................................................................................................................20
56 DMX Channels.....................................................................................................................................................22
Maintenance....................................................................................................................................................................23
Troubleshooting ...............................................................................................................................................................23
No Light.........................................................................................................................................................................23
No Response to DMX..................................................................................................................................................23
Product Specifications....................................................................................................................................................25
Dimensions........................................................................................................................................................................26

2
Ordercode: 41281
Candela Pix 100
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear to be damaged from shipping or the carton
itself shows signs of mishandling. Save the carton and all packing materials. In the event that the fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box and
packing.
Your shipment includes:
●Showtec Candela Pix 100
●2 brackets and screws
●Quick lock
●PowerCON True 1powercable 1,5m
●User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
●be qualified
●follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.

3
Ordercode: 41281
Candela Pix 100
Please consider that damages caused by manual modifications to the device are not subject to
warranty. This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
●Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
●Never modify, bend, mechanically strain, put pressure on, pull or heat up the power cord.
●Never strain the cable insert or the female part in the device. There must always be sufficient cable
going to the device. Otherwise, the cable will be damaged, which can cause serious damage.
●Never remove warning or informative labels from the unit.
●Never use anything to cover the ground contact.
●Never lift the device holding it by the projector-head, as the mechanics may be damaged. Always
hold the device by the transport handles.
●Never place any material over the LEDs or lens.
●Never look directly into the light source.
●Never leave any cables lying around.
●Never use the device during thunderstorms, unplug the device immediately.
●Never leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach, as they are potential sources of danger.
●Do not insert objects into air vents.
●Do not open the device and do not modify the device.
●Do not connect this device to a dimmer pack.
●Do not switch the device on and off in short intervals, as this will reduce the device’s life.
●Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Allow the device to cool for at least 5 minutes before handling.
●Do not shake the device. Avoid brute force when installing or operating the device.
●Only operate the device after having checked if the housing is firmly closed and all screws are tightly
fastened.
●Only operate the device after having familiarized with its functions.
●Avoid flames and do not put close to flammable liquids or gases.
●Always keep the case closed while operating.
●Always allow a free air space of at least 50 cm around the unit for ventilation.
●Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord holding it by the plug. Never pull out the plug by tugging the power cord.
●Make sure that the device is not exposed to extreme heat, moisture or dust.
●Make sure that the available voltage is not higher than stated on the rear panel.
●Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
●Make sure that the core diameter of extension cords and power cords is sufficient for the required
power consumption of the device.
●If the lens or LEDs are obviously damaged, it has to be replaced to prevent its functions from being
impaired, due to cracks or deep scratches.
●If the external cable is damaged, it has to be replaced by a qualified technician.
●If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
●If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
●If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
●For adult use only. The device must be installed beyond the reach of children. Never leave the unit
running unattended.
●Never attempt to bypass the thermostatic switch or fuses.
●For replacement use fuses of same type and rating only.
●The user is responsible for correct positioning and operating of the device. The manufacturer will not
accept liability for damages caused by the misuse or incorrect installation of this device.

4
Ordercode: 41281
Candela Pix 100
●This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
●Repairs, servicing and electric connection must be carried out by a qualified technician.
●WARRANTY: Till one year after date of purchase.
Operating Determinations
●This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
●The minimum distance between light output and the illuminated surface must be bigger than 1
meter.
●In order to eliminate wear and improve the device’s lifespan, during periods of non-use, completely
disconnect from power source via breaker or by unplugging.
●The maximum ambient temperature ta= 40°C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 40°C.
●If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
●Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself!
Always let the installation be carried out by an authorized dealer!
Procedure:
●If the device is lowered from the ceiling or high joists, professional trussing systems have to be used.
●Use a clamp to mount the device, with the mounting-bracket, to the trussing system.
●The device must never be fixed swinging freely in the room.
●The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety-cable.
●When rigging, derigging or servicing the device, always make sure, that the area below the
installation place is blocked and staying in the area is forbidden.
The Candela Pix 100 can be placed on a flat stage floor or mounted to any kind of truss by a clamp.
Improper installation can cause serious injuries and/or damage of property!

5
Ordercode: 41281
Candela Pix 100
Connection with the mains
Connect the device to the mains with the power plug.
Always check if the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE
GROUND
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage and/or damage of property!
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause of
the return. Be sure to properly pack fixture as any shipping damage resulting from inadequate packaging
is the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that the fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period, complaints will not be handled anymore.
Complaints will only be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.

6
Ordercode: 41281
Candela Pix 100
Description of the device
Features
The Showtec Candela Pix 100 is an outdoor LED bar with 14 x 4-in-1 RGBW LEDs. It is is a LED bar with high
output and great effects.
●Power and data daisy chain
●Pixel control
●OLED display
●Power Supply: 100-240V AC, 50/60Hz
●Power consumption: 200W @FO
●Drive current: 1000mA
●Refresh rate: 250 Hz, 4 kHz, 8 kHz, 16 kHz
●Light source: 14 x 15W 4-in-1 RGBW LEDs
●Beam angle: 8º
●Lux @2m: Red: 1900
Green: 5372
Blue: 890
White: 6259
Full Output: 11000
●Max. distance: 10m
●Lens plate: Tempered glass
●IP rating: IP-65
●Control Mode: DMX512
●DMX modes: 4, 6, 9 or 56 channels
●Control: Auto Program, Built-in programs, Manual, Master/Slave, DMX
●Dimmer: 0-100%
●Strobe: 0-20Hz
●Connections: Dedicated PowerCON True 1 IP65 (IN/OUT), Dedicated 3 pin XLR IP65 (IN/OUT)
●Housing: black aluminum
●Cooling: Aluminum housing
●Dimensions: 1024 x 150 x 235 mm (LxWxH) (incl. brackets)
●Weight: 11 kg
Note: Knowledge of DMX is required to fully utilize this unit.
Optional accessories
41282 Diffuser for Candela Pix 50 (20º)
41283 Diffuser for Candela Pix 50 (40º)

7
Ordercode: 41281
Candela Pix 100
Overview
Fig. 01
01) 14 x 15W 4-in-1 RGBW LEDs
02) Mounting bracket with inclination screw
Backside
Fig. 02
03) Dedicated PowerCON True 1 connector 100-240V IN (IP65)
04) Dedicated PowerCON True 1 connector 100-240V OUT (IP65)
05) Quick lock
06) Dedicated 3-pin DMX signal connector IN (IP65)
07) Dedicated 3-pin DMX signal connector OUT (IP65)
Side
Fig. 03
08) OLED display with Menu buttons

8
Ordercode: 41281
Candela Pix 100
Installation
Remove all packing materials from the Candela Pix 100.
Check that all foam and plastic padding is removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply.
Control Modes
There are 5 modes:
●Auto program
●Built-in programs
●Manual
●Master/Slave
●DMX512 (CH4, CH6, CH9, CH56)
One Candela Pix (Auto program, Built-in programs and Manual control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Candela Pix 100 is not connected with a DMX cable, it functions as a stand-alone device.
Please see page 14 for more information about the Auto program mode, Built-in programs or
Manual color mode.
Multiple Candela Pixs (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-p XLR cable to connect the Candela Pixs and other devices.
The pins:
1. Earth
2. Signal (-)
3. Signal (+)
05) Link the units as shown in Fig. 04, connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second and third unit. You can use the
same functions on the master device as described on page 14 (Auto program, Built-in programs or
Manual color mode). This means you can set your desired operation mode on the master device
and all slave devices will react the same as the master device.
Multiple Candela Pixs (Master/Slave control)
Fig. 04

9
Ordercode: 41281
Candela Pix 100
Multiple Candela Pixs (DMX512 Mode)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-p XLR cable to connect the Candela Pixs and other devices.
04) Link the units as shown in Fig. 05, Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second and third unit.
05) Supply electric power: Plug electric mains power cords into each unit's PowerCON True 1 socket,
then plug the other end of the mains power cord into proper electric power supply sockets, starting
with the first unit. Do not supply power before the whole system is set up and connected properly.
Multiple Candela Pixs DMX Set Up
Fig. 05
Note: Link all cables before connecting electric power!

10
Ordercode: 41281
Candela Pix 100
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy chained in one single line. To comply with the
EIA-485 standard no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number on a DMX data link: 30 fixtures
Maximum recommended number of fixtures on a power link: 6 @100V
Maximum recommended number of fixtures on a power link: 14 @240V
Data Cabling
To link fixtures together you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
●DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin. Ordercode
FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
●DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
●DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
●DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
●DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
●DAP Audio data cable FL08 DMX/AES-EBU, XLR/M 5-pin > XLR/F 5-pin.Ordercode FL08150 (1,5 m),
FL083 (3 m), FL086 (6 m), FL0810 (10 m), FL0820 (20 m).
●DAP Audio DMX adapter: 5-pin > 3-pin. Ordercode FLA29.
●DAP Audio DMX adapter: 3-pin > 5-pin. Ordercode FLA30.
●DAP Audio DMX Terminator 3-pin. Ordercode FLA42.
●DAP Audio DMX Terminator 5-pin. Ordercode FLA43.
The Candela Pix 100 can be operated with a controller in control mode or without the controller in
stand-alone mode.

11
Ordercode: 41281
Candela Pix 100
Control Panel
A. OLED Display
B. MODE button
C. UP Button
D. SET Button
E. DOWN Button
Fig. 06
DMX Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address the next time.)
DMX Addressing
The control panel on the backside of the device allows you to assign the DMX fixture address, which is
the first channel from which the Candela Pix will respond to the controller. Please note when you use the
controller, the unit has up to 56 channels. When using multiple Candela Pixs, make sure you set the DMX
addresses right. Therefore, the DMX address of the first Candela Pix should be 1(001); the DMX address of
the second Candela Pix should be 1+56=57 (057); the DMX address of the third Candela Pix 100 should
be 57+56=113 (113), etc. Please, be sure that you do not have any overlapping channels in order to
control each Candela Pix correctly. If two or more Candela Pixs are addressed similarly, they will work
similarly.
Controlling:
After having addressed all Candela Pixs, you may now start operating these via your lighting controller.
Note: After switching on, the Candela Pix will automatically detect whether DMX 512 data is received or
not. If there is no data received at the DMX-input, the text “DMX In“ on the control panel will not appear.
If not, the problem may be:
●The XLR cable from the controller is not connected with the input of the Candela Pix.
●The controller is switched off or defective, the cable or connector is defective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert a XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
Display Off after 30 seconds
When no button is pressed for 30 seconds, the display will turn off. To light up the display, you have to
press the MODE, SET, UP or DOWN button. Once you have pressed the button, the display will light up.

12
Ordercode: 41281
Candela Pix 100
Menu overview
The Candela Pix 100 will show the current software version and current temperature at start-up !

13
Ordercode: 41281
Candela Pix 100
Main Menu Options
01) Press the MODE or SET button to open the main menu.
02) Press the UP/DOWN buttons to scroll through the menu. The display will show:
03) Press the SET button to open the desired menu.
04) Press the MODE button to return to the previous menu.
1. DMX Address/ DMX Configuration
In this menu you can set the DMX address and DMX configuration.
01) While in the main menu, press the UP/DOWN buttons until the display shows DMX.
02) Press the SET button to open the menu, the display will show:
03) With the UP/DOWN buttons you can set the DMX address or the desired DMX configuration.
04) If you choose the desired DMX address , press the SET button to open the submenu.
05) Press the UP/DOWN buttons to set the desired address. The adjustment range is between
.
06) If you choose the desired DMX configuration , press the SET button to open the submenu.
07) Press the UP/DOWN buttons to choose one of the 4 options:
4 Channel
6 Channels
9 Channels
56 Channels
08) Press the SET button to confirm your choice.

14
Ordercode: 41281
Candela Pix 100
2. Manual
In this menu you can individually set the static colors.
01) While in main menu, press the UP/DOWN buttons until the display shows Manual.
02) Press the SET button to open the menu, the display will show:
03) Press the UP/DOWN buttons to scroll between the static colors Red, Green, Blue and White.
04) If you choose the desired color, press the SET button to adjust the color intensity.
05) Press the UP/DOWN buttons to set the intensity from the desired colors, the adjustment ranges are
between:
Red
Green
Blue
White
3. Auto program
In this menu you can activate the Auto program.
01) While in main menu, press the UP/DOWN buttons until the display shows Auto.
02) Press the SET button to open the menu, the display will show:
03) Press the UP/DOWN buttons to choose between Yes or No.
04) If you choose Yes, the Candela Pix will immediately start the Auto program.
05) If you choose No, the Candela Pix doesn’t start the Auto program and the output will blackout.
06) Press the SET button to confirm your choice.
4. Built-in programs
In this menu you can set the built-in programs.
01) While in main menu, press the UP/DOWN buttons until the display shows Program.
02) Press the SET button to open the menu, the display will show:
03) Press the SET button to open the submenu and use the UP/DOWN buttons to choose between the
built-in programs. The adjustment range is between .
04) If you choose , press the UP/DOWN buttons to choose the desired color or set the strobe
frequency.
05) If you choose the color , press the SET button to open the submenu.
06) Press the UP/DOWN buttons to choose one of the 38 available preset colors
.
07) If you choose the strobe frequency , press the SET button to open the submenu.

15
Ordercode: 41281
Candela Pix 100
08) Press the UP/DOWN buttons to set the desired strobe frequency. The adjustment range is between
, from OFF to high strobe frequency.
09) If you choose , press the UP/DOWN buttons to set the program speed and
strobe frequency.
10) If you choose the program speed , press the SET button to open the submenu.
11) Press the UP/DOWN buttons to set the desired program speed. The adjustment range is between
, from slow to fast.
12) If you choose the strobe frequency , press the SET button to open the submenu.
13) Press the UP/DOWN buttons to set the desired strobe frequency. The adjustment range is between
, from OFF to high strobe frequency.
5. Master/slave
In this menu you can set the device as a slave.
01) While in main menu, press the UP/DOWN buttons until the display shows Slave.
02) Press the SET button to open the menu, the display will show:
03) If you choose Yes, the device will become a slave device.
04) If the device has been set to slave, it will react the same as its master device.
05) If you choose No, it is automatically classified as a master device.
06) Press the SET button to confirm your choice.
6. Settings
In this menu you can set several settings of the device.
01) While in main menu, press the UP/DOWN buttons until the display shows Settings.
02) Press the SET button to open the menu, the display will show:
03) Press the UP/DOWN buttons to scroll between the following menus: Curves Select, Pixel Invert, PWM
Frequency, DMX Fail, DMX Sync, Lock, Key Back Light and Factory.

16
Ordercode: 41281
Candela Pix 100
6.1. Curves Select
In this menu you can adjust the dimming of the device by choosing a dimming curve.
01) Press the UP/DOWN buttons until the display shows Curves Select.
02) Press the SET button to open the menu, the display will show:
03) Press the UP/DOWN buttons to choose the desired dimming curve out of the 4 available options:
04) Press the SET button to confirm your choice.
6.2. Pixel Invert
In this menu you can adjust the Pixel direction of the device.
01) Press the UP/DOWN buttons until the display shows Pixel Invert.
02) Press the SET button to open the menu, the display will show:
03) Press the UP/DOWN buttons to select Yes or No.
04) If you choose Yes and confirm it with the SET button, the output of the device will be in the opposite
pixel direction.
05) If you choose No, the output of the device will be in the default pixel direction.

17
Ordercode: 41281
Candela Pix 100
6.3. PWM Frequency
In this menu you can choose several PWM frequencies.
01) Press the UP/DOWN buttons until the display shows PWM Frequency.
02) Press the SET button to open the menu, the display will show:
03) Press the UP/DOWN buttons to select one of the 4 options.
04) Press the SET button to confirm your choice.
6.4. DMX Fail
In this menu you can adjust the behaviour of the device in case of a DMX signal error.
01) Press the UP/DOWN buttons until the display shows Dmx Fail.
02) Press the SET button to open the menu, the display will show:
03) Press the UP/DOWN buttons to choose one of the 4 options.
04) If you choose Off, the output will blackout when a DMX signal error occurs.
05) If you choose Hold, the device will fall back on the last properly working DMX signal from before the
DMX signal error, which ensures undisrupted performance.
06) If you choose Manual, the device will fall back on the last setting in the Manual mode before the
DMX signal error.
07) If you choose Program, the device will fall back on the last setting in the Program mode before the
DMX signal error.
08) Press the SET button to confirm your choice.
6.5. DMX Sync
In this menu you can set the DMX synchronisation of the device.
01) Press the UP/DOWN buttons until the display shows Dmx Sync.
02) Press the SET button to open the menu, the display will show:
03) Press the UP/DOWN buttons to select On or Off.
04) The Sync option is a tool which helps to keep multiple fixtures synchronized, when using them in
master slave mode.
05) If you choose On, the synchronization function is activated, this is recommended.
06) If you choose Off, the synchronization function is not activated.
07) Press the SET button to confirm your choice.

18
Ordercode: 41281
Candela Pix 100
6.6. Lock
In this menu you can select whether the safety lock is active or not.
01) Press the UP/DOWN buttons until the display shows Lock.
02) Press the SET button to open the menu, the display will show:
03) Press the UP/DOWN buttons to select On or Off.
04) If you choose Yes and confirm it with the SET button, the device will be in Lock mode. You will need
to insert the password in order to access the main menu. Simultaneously press the MODE and SET
button for 3 seconds and you will be able to access the main menu.
05) If you choose No, the main menu will remain unlocked.
06) Press the SET button to confirm your choice.
6.7. Key Backlight
In this menu you can select whether the safety lock is active or not.
01) Press the UP/DOWN buttons until the display shows Key Backlight.
02) Press the SET button to open the menu, the display will show:
03) Press the UP/DOWN buttons to select On or Off.
04) If you choose On, the menu buttons will light up.
05) If you choose Off, the menu buttons will not light up.
06) Press the SET button to confirm your choice.
6.8. Factory
In this menu you can reset to the default settings.
01) Press the UP/DOWN buttons until the display shows Factory.
02) Press the SET button to open the menu, the display will show:
03) Press the UP/DOWN buttons to select Yes or No.
04) If you choose Yes and confirm it with the SET button, the device will reset to its factory default
settings.
05) If you choose No, the device will keep current settings.
7. Information
With this menu you can view the currently installed software version and temperature
01) In main menu, press the UP/DOWN buttons until the display shows Information.
02) Press the SET button to open the menu, the display will show:
03) You can view the currently installed software version, current temperature and the UID number.

19
Ordercode: 41281
Candela Pix 100
DMX Channels
4 Channels
Channel 1 –Red Dimmer intensity
0-255
Gradual adjustment Red from 0-100%
Channel 2 –Green Dimmer intensity
0-255
Gradual adjustment Green from 0-100%
Channel 3 –Blue Dimmer intensity
0-255
Gradual adjustment Blue from 0-100%
Channel 4 –White Dimmer intensity
0-255
Gradual adjustment White from 0-100%
6 Channels
Channel 1 –Master Dimmer intensity
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 2 –Red Dimmer intensity (CH1 must be set between 1-255 )
0-255
Gradual adjustment Red from 0-100%
Channel 3 –Green Dimmer intensity (CH1 must be set between 1-255 )
0-255
Gradual adjustment Green from 0-100%
Channel 4 –Blue Dimmer intensity (CH1 must be set between 1-255 )
0-255
Gradual adjustment Blue from 0-100%
Channel 5 –White Dimmer intensity (CH1 must be set between 1-255 )
0-255
Gradual adjustment White from 0-100%
Channel 6 –Strobe (CH1 and CH2, CH3, CH4 or CH5 must be set between 1-255 )
0-10
Closed
11-255
Strobe flash frequency, from low to high frequency (0-20 Hz)