Show Tec EventSpot 1600 Q4 User manual

EventSpot 1600 Q4 V1
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 44051
MANUAL
ENGLISH

1
Ordercode: 44051
EventSpot 1600 Q4
Table of contents
Warning ...............................................................................................................................................................................3
Safety Instructions .........................................................................................................................................................3
Operating Determinations ..........................................................................................................................................5
Rigging ............................................................................................................................................................................5
Connection with the mains.........................................................................................................................................6
Return Procedure..........................................................................................................................................................7
Claims..............................................................................................................................................................................7
Description of the device.................................................................................................................................................8
Optional accessories....................................................................................................................................................8
Overview ........................................................................................................................................................................9
Bottom.............................................................................................................................................................................9
Backside .......................................................................................................................................................................10
Installation.........................................................................................................................................................................10
Set Up and Operation .....................................................................................................................................................10
Charging the built-in battery ....................................................................................................................................10
Control Modes.............................................................................................................................................................11
One EventSpot (Manual) .......................................................................................................................................11
One EventSpot (Auto program) ...........................................................................................................................11
One EventSpot (Built-in programs) .......................................................................................................................11
Multiple EventSpots (Master/Slave control)........................................................................................................12
Multiple EventSpots (DMX Control) ......................................................................................................................13
Multiple EventSpots (Wireless DMX Control) .......................................................................................................14
Connect the EventSpot 1600 Q4 to the Wireless DMX signal transmitter .....................................................15
Disconnect from the Wireless DMX signal transmitter.......................................................................................15
Fixture Linking ...............................................................................................................................................................16
Data Cabling...............................................................................................................................................................16
Control Panel ...............................................................................................................................................................17
DMX Control Mode.....................................................................................................................................................17
DMX Addressing ..........................................................................................................................................................17
Menu overview............................................................................................................................................................18
Main Menu Options....................................................................................................................................................19
1. DMX Address/ DMX Configuration/DMX signal .............................................................................................19
2. Manual...................................................................................................................................................................20
3. Auto program.......................................................................................................................................................20
4. Built-in programs ..................................................................................................................................................20
5. Master/slave .........................................................................................................................................................21
6. Settings...................................................................................................................................................................21
6.1. Curves Select ....................................................................................................................................................22
6.2. Dimmer Speed ..................................................................................................................................................22
6.3. DMX Fail..............................................................................................................................................................23
6.4. Working Time .....................................................................................................................................................23
6.5. DMX Sync ...........................................................................................................................................................23
6.6. Lock.....................................................................................................................................................................24
6.7. Calibration .........................................................................................................................................................24
6.8. Factory................................................................................................................................................................24
7. Information............................................................................................................................................................25
Optional remote control ...........................................................................................................................................25
Auto program...........................................................................................................................................................26
Built-in programs.......................................................................................................................................................26
Manual mode...........................................................................................................................................................26
DMX Channels .............................................................................................................................................................27
4 Channels ................................................................................................................................................................27
6 Channels ................................................................................................................................................................27
10 Channels ..............................................................................................................................................................27

2
Ordercode: 44051
EventSpot 1600 Q4
Maintenance....................................................................................................................................................................29
Troubleshooting ...............................................................................................................................................................30
No Light.........................................................................................................................................................................30
No Response to DMX..................................................................................................................................................30
Product Specifications....................................................................................................................................................32
Dimensions........................................................................................................................................................................33
Notes ..................................................................................................................................................................................34

3
Ordercode: 44051
EventSpot 1600 Q4
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear to be damaged from shipping or the carton
itself shows signs of mishandling. Save the carton and all packing materials. In the event that the fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box and
packing.
Your shipment includes:
●EventSpot 1600 Q4
●User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
●be qualified
●follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.

4
Ordercode: 44051
EventSpot 1600 Q4
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
●Never remove warning or informative labels from the unit.
●Never use anything to cover the ground contact.
●Never place any material over the lens.
●Never look directly into the light source.
●Never leave any cables lying around.
●Do not insert objects into air vents.
●Do not connect this device to a dimmerpack.
●Do not switch the device on and off in short intervals, as this would reduce the device’s lifespan.
●Do not touch the device’s housing bare-handed during its operation. Allow the fixture to cool for at
least 5 minutes before handling.
●Do not shake the device. Avoid brute force when installing or operating the device.
●Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
●Only operate the device after having familiarized with its functions.
●Avoid flames and do not put close to flammable liquids or gases.
●Always keep case closed while operating.
●Always allow free air space of at least 50 cm around the unit for ventilation.
●Make sure that the device is not exposed to extreme heat, moisture or dust.
●Make sure that the available voltage is not higher than stated on the rear panel.
●If the lens is obviously damaged, it has to be replaced to prevent its functions from being impaired,
due to cracks or deep scratches.
●If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
●If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
●If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
●For adult use only. Device must be installed out of reach of children. Never leave the unit running
unattended.
●Never attempt to bypass the thermostatic switch or fuses.
●For replacement, use fuses of same type and rating only.
●The user is responsible for correct positioning and operating of the Showtec EventSpot 1600 Q4. The
manufacturer will not accept liability for damages caused by the misuse or incorrect installation of
this device.
●This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
●Repairs, servicing and electrical connection must be carried out by a qualified technician.
●WARRANTY: Till one year after date of purchase.
●WARRANTY: on batteries is only 6 months after date of purchase.
When your battery remains dead after fully charging or it doesn’t function or doesn’t charge
anymore, you can order a new battery. The spare part number for the battery is on request.

5
Ordercode: 44051
EventSpot 1600 Q4
Operating Determinations
●This device is not designed for permanent operation. Regular operation breaks will ensure that the
device will serve you for a long time without defects.
●The minimum distance between light-output and the illuminated surface must be bigger than 0,5
meter.
●In order to eliminate wear and improve the device’s lifespan, during periods of non-use, completely
disconnect from power source via breaker or by unplugging.
●The maximum ambient temperature ta = 40°C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
●If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
●Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself!
Always let the installation be carried out by an authorized dealer!
Procedure:
●If the device is lowered from the ceiling or high joists, professional trussing systems have to be used.
●Use a clamp to mount the device, with the mounting-bracket, to the trussing system.
●The device must never be fixed swinging freely in the room.
●The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
●When rigging, derigging or servicing the device, always make sure, that the area below the
installation place is blocked and staying in the area is forbidden.

6
Ordercode: 44051
EventSpot 1600 Q4
The EventSpot 1600 Q4 can be placed on a flat surface or fitted to any kind of truss with a clamp.
Improper installation can cause serious damage to people and property!
Connection with the mains
Connect the device to the mains with the power plug.
Always check if the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE
GROUND
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!

7
Ordercode: 44051
EventSpot 1600 Q4
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause of
the return. Be sure to properly pack fixture as any shipping damage resulting from inadequate packaging
is the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that the fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period, complaints will not be handled anymore.
Complaints will only be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.

8
Ordercode: 44051
EventSpot 1600 Q4
Description of the device
Features
The EventSpot 1600 Q4 is a wireless LED Eventspot from Showtec.
●Long battery life
●Eco mode for extended batterylife
●IP-54 for outdoor use
●Wireless DMX by Wireless Solutions Sweden
●Input Voltage: 100~240V AC, 50/60Hz
●Batttery storage: 15,6Ah
●Light source: 4 x 12W RGBW LEDs
●Drive current: 650mA
●Refresh rate: 12KHz
●Liminus flux: 1580
●Lux@2m: 15000
●Operating time at Full On: 8 hours at full RGBW on
●Charging time: 6 hours
●Battery type: Litium ion
●Voltage: 18,5V
●Spare battery: On request
●OLED display for easy setup
●Control Protocol: DMX512 via wireless/ DMX512
●DMX channels: 4, 6 or 10 channels
●Control modes: Built-in programs, Auto, Manual, Master/Slave, DMX, W-DMX
●Beam angle: 10°
●Dimmer: 0-100%
●Strobe: 0-15Hz
●Housing: Black aluminum and iron
●IP rating: IP54
●Connections: Dedicated 3-pin XLR IN/OUT IP54
●Cooling: Aluminum heatsink
●Operation Temperature: -10°C ~40°C
●Dimensions: 180 x 180 x 280 mm (LxWxH)
●Weight: 5,0 Kg
Note: Knowledge of DMX is required to fully utilize this unit.
Optional accessories
44002 –Showtec UR-5 Universal IR Remote
44052 –Charger for EventSpot 1600 Q4
44053 –Beamshaper for Eventspot 1600 Q4 (40°)
44054 –Beamshaper for Eventspot 1600 Q4 (15° x 60°)
44055 –Beamshaper for Eventspot 1600 Q4 (20°)
50175 –W-DMX MicroBox F-1 G5 Transceiver

9
Ordercode: 44051
EventSpot 1600 Q4
Overview
Fig. 01
01) Adjustment knob
02) 4 x 12W RGBW LEDs
03) OLED display + control buttons
Bottom
Fig. 02
04) Dedicated 3-pin DMX signal connector IN IP54
05) Main power button ON/OFF
06) Dedicated 3-pin DMX signal connector OUT IP54
07) Quick lock mounting hole
08) Battery charger socket

10
Ordercode: 44051
EventSpot 1600 Q4
Backside
Fig. 03
09) Wireless DMX receiving antenna
Installation
Remove all packing materials from the EventSpot 1600 Q4. Check that all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Charging the built-in battery
01) In order to charge the battery you need the optional charger 44052 (is not included!).
02) Turn off the power.
03) Connect the EventSpot to the charger (fig 04).
04) Please make sure that the battery socket from the EventSpot covers the socket from the
charger (fig 04).
05) Connect the charger to a powerCON to Schuko power cable.
06) Then plug the other end of the powerCON to Schuko power cable into a proper electric power
supply socket.
07) Charge the battery within 6 hours.
08) The four LED indicators from the charger will light up green when the EventSpot is fully charged.

11
Ordercode: 44051
EventSpot 1600 Q4
Fig. 04
Important!
●Do not charge for more than 24 hours.
●Recharge within 3 days of use.
●Press the Main power button (05) to off at the underside when storing for more than 7 days.
●Store in an upright position.
Control Modes
There are 6 modes:
Manual (stand alone)
Auto program (stand alone)
Built-in programs (stand alone)
Master/Slave
DMX512
Wireless DMX (W-DMX)
One EventSpot (Manual)
When the EventSpot is not connected by a DMX-cable and Wireless DMX is switched off, it functions as
a stand-alone device. See page 20 for more information about the Manual mode.
One EventSpot (Auto program)
When the EventSpot is not connected by a DMX-cable and Wireless DMX is switched off, it functions as a
stand-alone device. See page 20 for more information about the Auto program.
One EventSpot (Built-in programs)
When the EventSpot is not connected by a DMX-cable and Wireless DMX is switched off, it functions as a
stand-alone device. See pages 20-21 for more information about the Built-in programs.

12
Ordercode: 44051
EventSpot 1600 Q4
Multiple EventSpots (Master/Slave control)
01) Use a 3-p XLR cable to connect the EventSpots and other devices.
The pins:
1. Earth
2. Signal (-)
3. Signal (+)
02) Link the units as shown in (Fig. 05), connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third and fourth units. You can
use the same functions on the master device as described on pages 20-21 (Manual, Auto program
or Built-in programs). This means you can set your desired operation mode on the master device and
all slave devices will react the same as the master device.
Multiple EventSpots (Master/Slave control)
Fig. 05

13
Ordercode: 44051
EventSpot 1600 Q4
Multiple EventSpots (DMX Control)
01) Leave at least 0,5 meter on all sides for air circulation
02) Use a 3-p XLR cable to connect the EventSpots and other devices.
03) Link the units as shown in (figure 06), connect a DMX signal cable from the first unit's DMX "out"
socket to the second unit's "in" socket. Repeat this process to link the second, third and fourth units.
Multiple EventSpots DMX Set Up
Fig. 06

14
Ordercode: 44051
EventSpot 1600 Q4
Multiple EventSpots (Wireless DMX Control)
01) Place the EventSpots at the desired position (see page 15 for maximum WiFi distance).
02) When the W-DMX LED indicator (C) is blinking (green), the device is searching for a connection.
03) Connect the transmitter with multiple EventSpots. In order to create a Wireless match, please check
the manual of your wireless signal transmitter.
04) When there is a connection, the W-DMX LED indicator (C) from the EventSpot will light up green.
05) Use a DMX-cable to link the transmitter with a suitable lightcontroller.
Setup example wireless DMX
Fig. 07

15
Ordercode: 44051
EventSpot 1600 Q4
Sweden 2.4GHz Wireless communication module
Communication distance:
Depending on the transmitting power or transmitter module
Test conditions:
W-DMX TRx Transmitter module, 2dBi Antenna, transmitting power
20dBm (100mW)
Range indoor:
60m (approx. through three concrete walls)
Range outdoor:
250m
Wireless DMX connection
The wireless receiving module “Pico G4 Receiver, 2.4GHz”, provided by Swedish WIRELESS SOLUTION, only
has a 2.4 GHz wireless signal receiving function. In order to match the wireless signal, please use the 50175
W-DMX MicroBox F-1 G5 Transceiver by WIRELESS SOLUTION. To control the status of the wireless
communication, please look at the green LED indicator on the control panel of the fixture.
Wi-fi Problems:
01) No emitter/sender matching.
The LED Indicator dims for a long period of time.
02) Matching signal with one emitter, but loss of signal communication.
The LED Indicator light will light up for 100ms and then dim for 100ms; The LED will flicker quickly.
03) Communication with an emitter, but no DMX data.
The LED Indicator will light up for 900ms and then dim for 100ms; The LED will flicker slowly.
When the wireless DMX communication is normal, the LED indicator will always be on.
The EventSpot 1600 Q4 cannot receive a wireless DMX signal and a DMX
cable signal at the same time
When the device is in manual, auto program or built-in program, please ensure that the matching 2.4GHz
wireless signal transmitter is OFF.
Connect the EventSpot 1600 Q4 to the Wireless DMX signal transmitter
The EventSpot 1600 Q4 cannot actively match a random wireless signal transmitter.
In order to create a Wireless match, please check the manual of your wireless signal transmitter.
We advise you to use the W-DMX MicroBox F-1 G5 Transceiver (50175) by WIRELESS SOLUTION (Fig. 08).
Ordercode: 50175
Fig. 08
Disconnect from the Wireless DMX signal transmitter
The EventSpot 1600 Q4 can be disconnected from the wireless DMX signal transmitter.
You can turn off/unlink the W-DMX if you press the W-DMX button (H) for 3 seconds.
The EventSpot will be disconnected.

16
Ordercode: 44051
EventSpot 1600 Q4
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy chained in one single line. To comply with the
EIA-485 standard no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of EventSpots on a DMX data link: 30 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
●DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin. Ordercode
FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
●DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
●DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
●DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
●DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
●DAP Audio data cable FL08 DMX/AES-EBU, XLR/M 5-pin > XLR/F 5-pin.Ordercode FL08150 (1,5 m),
FL083 (3 m), FL086 (6 m), FL0810 (10 m), FL0820 (20 m).
●DAP Audio DMX adapter: 5-pin > 3-pin. Ordercode FLA29.
●DAP Audio DMX adapter: 3-pin > 5-pin. Ordercode FLA30.
●DAP Audio DMX Terminator 3-pin. Ordercode FLA42.
●DAP Audio DMX Terminator 5-pin. Ordercode FLA43.
The EventSpot 1600 Q4 can be operated with a controller in control mode or without the controller in
stand-alone mode.

17
Ordercode: 44051
EventSpot 1600 Q4
Control Panel
A)
B)
C)
D)
E)
F)
G)
H)
I)
OLED display
IR-remote sensor
W-DMX LED indicator
MODE button
UP button
SET button
Power button on/off
W-DMX button
DOWN button
Fig.09
DMX Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address, next time.)
DMX Addressing
The control panel on the back side of the device allows you to assign the DMX fixture address, which is
the first channel from which the EventSpot will respond to the controller. Please note when you use the
controller, the unit has up to 10 channels.
When using multiple EventSpots, make sure you set the DMX addresses right. Therefore, the DMX address
of the first EventSpot should be 1(001); the DMX address of the second EventSpot should be 1+10=11
(011); the DMX address of the third EventSpot should be 11+10=21 (021), etc. Please, be sure that you
don’t have any overlapping channels in order to control each EventSpot correctly. If two or more
EventSpots are addressed similarly, they will work similarly.
Controlling: After having addressed all EventSpots, you may now start operating these via your lighting
controller.
Note: After switching on, the EventSpot will automatically detect whether DMX 512 data is received or
not. If there is no data received at the DMX-input, the problem may be:
●The XLR cable from the controller is not connected with the input of the EventSpot.
●The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It’s necessary to insert a XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
Display Off after 60 seconds
When no button is pressed for 60 seconds, the display will turn off.
To light up the display, you have to press the MODE, SET, UP or DOWN button.
Once you have pressed the button, the display will light up.

18
Ordercode: 44051
EventSpot 1600 Q4
Menu overview

19
Ordercode: 44051
EventSpot 1600 Q4
First press the main power button (5) and then hold the power button (G) for at least 3 sec. to activate the
EventSpot! The EventSpot will show the current software version, battery energy level, actual temperature
and type of DMX signal at start-up !
Main Menu Options
01) Press the MODE or SET button to open the main menu.
02) Press the UP/DOWN buttons to scroll through the menu. The display will show:
03) Press the SET button to open the desired menu.
04) Press the MODE button to return to the previous menu.
1. DMX Address/ DMX Configuration/DMX signal
In this menu you can set the device’s DMX starting address, choose a DMX channel mode or choose
between the DMX signal options.
01) While in main menu, press the UP/DOWN buttons until the display shows DMX.
02) Press the SET button to open the menu, the display will show:
03) Press the UP/DOWN buttons to set the DMX address, the desired configuration and activate DMX or
W-DMX mode.
04) If you choose the DMX address , press the SET button to open the submenu.
05) Press the UP/DOWN buttons to set the desired address. The adjustment range is between
.
06) If you choose the DMX configuration , press the SET button to open the submenu.
07) Press the UP/DOWN buttons to choose between:
4 Channels
6 Channels
10 Channels
08) If you choose Signal, press the SET button to open the submenu:
09) Press the UP/DOWN buttons to select normal DMX or wireless DMX mode.
10) Press the SET button to confirm your choice.