Show Tec Polar 300 Hybrid V3 User manual

Polar 300 Hybrid IP65 Moving Head V3
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Order code: 40102
MANUAL
ENGLISH

1
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Table of contents
Warning ...............................................................................................................................................................................3
Safety Instructions .........................................................................................................................................................3
Operating Determinations ..........................................................................................................................................5
Rigging ............................................................................................................................................................................5
Connection with the Mains.........................................................................................................................................7
Return Procedure..........................................................................................................................................................7
Claims..............................................................................................................................................................................7
Description of the Device ................................................................................................................................................8
Features ..........................................................................................................................................................................8
Photometric Diagrams.................................................................................................................................................9
Front View.....................................................................................................................................................................10
Back View.....................................................................................................................................................................10
Installation.........................................................................................................................................................................11
Lock/Unlock the Moving Head ................................................................................................................................11
Setup and Operation ......................................................................................................................................................12
Control Modes.............................................................................................................................................................12
One Polar (Auto Program, Custom Programs)...................................................................................................12
One Polar (Manual).................................................................................................................................................12
Multiple Polars (Master/Slave Control) ................................................................................................................13
Multiple Polars (DMX Control)................................................................................................................................14
Multiple Polars (Art-Net/sACN Control/RDM) .....................................................................................................15
Multiple Polars (Wireless DMX Control) ................................................................................................................16
Connect the Polar to the Wireless DMX Signal Transmitter..............................................................................17
Disconnect the Polar from the Wireless DMX Signal Transmitter.....................................................................17
Connecting to a Network .........................................................................................................................................18
Art-Net Settings.........................................................................................................................................................18
sACN Settings............................................................................................................................................................18
How to Make a Data Cable.....................................................................................................................................19
Fixture Linking...............................................................................................................................................................20
Data Cabling...............................................................................................................................................................20
Control Panel ...............................................................................................................................................................21
DMX Addressing ..........................................................................................................................................................21
Menu Overview...........................................................................................................................................................22
Start-up..........................................................................................................................................................................26
No Reset Start-up ........................................................................................................................................................26
Main Menu Options....................................................................................................................................................27
1. DMX Address ........................................................................................................................................................27
2. Person (DMX Channel Modes)..........................................................................................................................27
3. Run Mode..............................................................................................................................................................28
4. Option....................................................................................................................................................................28
4.1. Display Lock.......................................................................................................................................................29
4.2. Settings ...............................................................................................................................................................29
4.2.1. Recovery.........................................................................................................................................................29
4.2.2. Clean Edit 1 ....................................................................................................................................................29
4.2.3. Clean Edit 2 ....................................................................................................................................................29
4.2.4. WDMX Hide.....................................................................................................................................................30
4.3. Network ..............................................................................................................................................................30
4.3.1. IP Mode ...........................................................................................................................................................30
4.3.2. Custom IP........................................................................................................................................................31
4.4. Signal...................................................................................................................................................................31
5. Edit ..........................................................................................................................................................................32
6. Manual...................................................................................................................................................................33
6.1. Channel..............................................................................................................................................................34
6.2. Reset ...................................................................................................................................................................35

2
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
7. Info..........................................................................................................................................................................35
7.1. System Error........................................................................................................................................................36
8. Service ...................................................................................................................................................................37
DMX Channels .............................................................................................................................................................38
20 Channels (Basic) .................................................................................................................................................38
24 Channels (Standard) .........................................................................................................................................42
28 Channels (Extended).........................................................................................................................................46
Maintenance....................................................................................................................................................................51
Replacing the Fuse.....................................................................................................................................................51
Replacing a Gobo From the Rotating Gobo Wheel ...........................................................................................52
Gobo Size .....................................................................................................................................................................53
Glass Gobo Orientation.............................................................................................................................................54
Gobo Wheels and Color Wheel...............................................................................................................................55
Troubleshooting ...............................................................................................................................................................56
No Light.........................................................................................................................................................................56
No Response to DMX..................................................................................................................................................56
Product Specifications....................................................................................................................................................58
Dimensions........................................................................................................................................................................59
Notes ..................................................................................................................................................................................60

3
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture will be returned in the original factory box and
packing.
Your shipment includes:
●Showtec Polar 300 Hybrid IP65 Moving Head
●Schuko to PowerCON True1 power cable (1,5 m)
●2 x quick-lock brackets
●User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason, when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
●be qualified
●follow the instructions of this manual
Before the initial start-up, please make sure that there is no damage caused by transportation.
Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes contained in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.

4
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
●Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
●Never modify, bend, mechanically strain, put pressure on, pull or heat up the power cord.
●Never strain the cable. There must always be sufficient cable going to the device. Otherwise, the
cable will be damaged, which can cause serious damage.
●Never remove warning or informative labels from the unit.
●Never use anything to cover the ground contact.
●Never lift the device holding it by the projector-head, as the mechanics may be damaged. Always
hold the device by the transport handles.
●Never place any material over the LEDs or lens.
●Never look directly into the light source.
●Never leave any cables lying around.
●Never use the device during thunderstorms, unplug the device immediately.
●Never leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach, as they are potential sources of danger.
●Do not insert objects into air vents.
●Do not open the device and do not modify the device.
●Do not connect this device to a dimmer pack.
●Do not switch the device on and off in short intervals, as this will reduce the device’s life.
●Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Allow the device to cool for at least 5 minutes before handling.
●Do not shake the device. Avoid brute force when installing or operating the device.
●Only operate the device after having checked if the housing is firmly closed and all screws are tightly
fastened.
●Only operate the device after having familiarized with its functions.
●Avoid flames and do not put close to flammable liquids or gases.
●Always allow a free air space of at least 1,3 m around the unit for ventilation.
●Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord holding it by the plug. Never pull out the plug by tugging the power cord.
●Make sure that the device is not exposed to extreme heat or dust.
●Make sure that the available voltage is not higher than stated on the rear panel.
●Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
●Make sure that the core diameter of extension cords and power cords is sufficient for the required
power consumption of the device.
●If the lens or LEDs are obviously damaged, they need to be replaced to prevent their functions from
being impaired, due to cracks or deep scratches.
●If the external cable is damaged, it has to be replaced by a qualified technician.
●If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
●If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
●If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
●For adult use only. The device must be installed beyond the reach of children. Never leave the unit
running unattended.
●Never attempt to bypass the thermostatic switch or fuses.
●For replacement use fuses of same type and rating only.
●This device is heavy. When handling, use a two-person lift to prevent injury.
●The user is responsible for correct positioning and operating of the device. The manufacturer will not
accept liability for damages caused by the misuse or incorrect installation of this device.
●This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.

5
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
●Repairs, servicing and electric connection must be carried out by a qualified technician.
●WARRANTY: Till one year after date of purchase.
Operating Determinations
●This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
●The minimum distance between light output and the illuminated surface must be bigger than 1,3 m.
●To eliminate wear and improve lifespan, during periods of non-use, completely disconnect from
power via breaker or by unplugging.
●The maximum ambient temperature ta= 40 °C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 40 °C.
●If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
●Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
You endanger your own safety and the safety of others!
Rigging
This device is heavy. When handling, use a two-person lift to prevent injury.
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself!
Always let the installation be carried out by an authorized dealer!
Procedure:
●If the Polar is lowered from the ceiling or high joists, professional trussing systems have to be used.
●Use clamps to mount the Polar with the mounting brackets to the trussing system.
●The Polar must never be fixed swinging freely in the room.
●The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
●When rigging, derigging or servicing the Polar, always make sure, that the area below the installation
site is secured and that there are not any unauthorized people around.

6
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Fig. 01
The Polar can be placed on a flat stage floor or mounted to any kind of truss with quick-lock brackets
and clamps (see Fig. 01).
The quick-lock brackets can be positioned on the base of the Polar in two ways, as shown on Fig. 02.
Fig. 02
Improper installation can cause serious injuries and/or damage of property!

7
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Connection with the Mains
Connect the device to the mains with the power-plug.
Always check if the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE
GROUND
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause for
the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is
the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to report and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be prepared in writing or sent by fax within 10 working days after receipt of
the invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement from which the obligation is resulting.

8
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Description of the Device
Features
The Polar 300 Hybrid is a moving head with high output and great effects.
●Input voltage: 100–240 V AC, 50/60 Hz (auto-ranging)
●Power consumption: 400 W (max)
●Light source: 300 W LED Module
●Light output: 22750 Lux @ 10 m (3°); 71250 Lux @ 1 m (30°)
●Dimmer: 0–100 % (16 bit)
●Strobe: 0–25 Hz
●Beam angle: 3–30°
●Focus: Motorized linear focus
●Control protocol: DMX-512, Art-Net, sACN, RDM, W-DMX
●Control personality: 20 channels (Basic), 24 channels (Standard), 28 channels (Extended)
●Pan: 0º–540º
●Tilt: 0º–270º
●Pan/Tilt resolution: 8–16 bit
●Special: Pan/Tilt movement blackout, user selectable Pan/Tilt ranges, reverse Pan/Tilt movement
●Control modes: Stand alone, Manual, Master/Slave, DMX-512, Art-Net/sACN, W-DMX
●Color wheels: CMY wheels, 8 dichroic filters + white
●Rotating gobo wheel: 8 gobos + white
●Static gobo wheel: 12 gobos + white
●Color functions: Rainbow flow effect, split colors, CMY color mixing, CMY color macros
●Gobo functions: Gobo flow effect, gobo shake, gobo bounce, bidirectional rotation
●Prism: 5-facet circular prism
●Prism functions: Bidirectional rotation, adjustable speed
●Frost filter: Yes, linear adjustment
●Display: LCD, battery-powered
●Housing: Flame-retardant plastic, die-cast aluminum
●Color: Black
●Cooling: Forced convection
●IP rating: IP65
●Connections: IP-65 rated power connector True1 IN, IP-65 rated 5-pin DMX IN/OUT connectors,
2 x IP-65 rated RJ45 connectors
●Fuse: T6,3 A/250 V
●Dimensions: 670 x 416 x 356 mm (L x W x H)
●Weight: 34,6 kg

9
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Photometric Diagrams
Fig. 03

10
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Front View
Fig. 04
01) 300 W LED Module
02) Tilt lock pin
03) Pan lock pin
04) Control panel: LCD display and control buttons
Back View
Fig. 05
05) IP-65 rated power connector True1 IN
06) Fuse T6,3 A/250 V
07) IP-65 rated RJ45 connector
08) IP-65 rated RJ45 connector
09) IP-65 rated 5-pin DMX signal connector OUT
10) IP-65 rated 5-pin DMX signal connector IN

11
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Installation
Remove all packing materials from the Polar 300 Hybrid Moving Head. Check if all foam and plastic
padding is removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Lock/Unlock the Moving Head
You can lock/unlock the moving head by sliding the lock pins:
●Slide the tilt lock pin (02) upwards to disable and downwards to enable the vertical movement (Tilt)
of the fixture (see Fig. 06).
●Slide the pan lock pin (03) to the left to disable and to the right to enable the horizontal movement
(Pan) of the fixture (see Fig. 06).
Always lock the moving head before transportation!
Make sure to release the lock pins before operating the fixture.
Fig. 06

12
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Setup and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 110 V specification product on 240 V power, or vice versa.
Connect the device to the main power supply.
Control Modes
There are 6 modes:
●Stand-alone (Auto program, Custom programs)
●Manual
●Master/Slave
●DMX-512 (20 CH, 24 CH, 28 CH)
●Art-Net/sACN (20 CH, 24 CH, 28 CH)
●W-DMX (20 CH, 24 CH, 28 CH)
One Polar (Auto Program, Custom Programs)
01) Fasten the effect light to a firm trussing or mount it on flat surface. Leave at least 1,3 m on all sides
for air circulation.
02) Secure the device with a safety cable (order code 70454 / 70456).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Polar is not connected with a DMX cable, it functions as a stand-alone device.
05) Please see 3. Run Mode on page 28 for more information.
One Polar (Manual)
01) Fasten the effect light to a firm trussing or mount it on flat surface. Leave at least 1,3 m on all sides
for air circulation.
02) Secure the device with a safety cable (order code 70454 / 70456).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Polar is not connected with a DMX cable, it functions as a stand-alone device.
05) Please see 6. Manual on page 33 for more information.

13
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Multiple Polars (Master/Slave Control)
01) Fasten the effect light onto firm trussing or mount it on flat surface. Leave at least 1,3 m on all sides for
air circulation.
02) Secure the device with a safety cable (order code 70454 / 70456).
03) Use a 5-pin DMX cable to connect the Polar to other devices.
The pins:
1. Earth
2. Signal (-)
3. Signal (+)
4. N/C
5. N/C
04) Link the units as shown in Fig. 07. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX cable. Repeat this process to link the rest of the units. The first connected device
will be automatically recognized as master device. To upload custom programs from the master
device to the slave devices, see 4. Option on pages 28–29.
05) Supply electric power: Plug electric mains power cords into each unit's power IN socket, then plug
the other end of the mains power cord into proper electric power supply sockets, starting with the
first unit. Do not supply power before the whole system is set up and connected properly.
Fig. 07
Note: Link all cables before connecting electric power

14
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Multiple Polars (DMX Control)
01) Fasten the effect light to a firm trussing or mount it on flat surface. Leave at least 1,3 m on all sides
for air circulation.
02) Secure the device with a safety cable (order code 70454 / 70456).
03) Use a 5-pin DMX cable to connect the Polar and other devices.
04) Link the units as shown in Fig. 08. Connect a light controller to the first unit's DMX "in" socket, using a
DMX cable. Connect the first unit’s "out" socket with the second unit's "in" socket, using a DMX
cable. Repeat this process to link the rest of the units.
05) Supply electric power: Plug electric mains power cords into each unit's power IN socket, then plug
the other end of the mains power cord into proper electric power supply sockets, starting with the
first unit. Do not supply power before the whole system is set up and connected properly.
Fig. 08
Note: Link all cables before connecting electric power

15
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Multiple Polars (Art-Net/sACN Control/RDM)
01) Fasten the effect light to a firm trussing or mount it on flat surface. Leave at least 1,3 m on all sides
for air circulation.
02) Secure the device with a safety cable (order code 70454 / 70456).
03) Use a CAT-5/CAT-6 cable to connect the Polar and other devices.
04) Connect your computer with installed Art-Net software to the first device’s RJ45 "in" socket.
05) Link the units as shown in Fig. 09. Connect the first unit's RJ45 "out" socket with the second unit's "in"
socket, using a CAT-5/CAT-6 cable. Repeat this process to link the rest of the units.
06) Supply electric power: Plug electric mains power cords into each unit's power IN socket, then plug
the other end of the mains power cord into proper electric power supply sockets, starting with the
first unit. Do not supply power before the whole system is set up and connected properly.
Fig. 09
Note: Link all cables before connecting electric power
Note: The Polar 300 Hybrid supports Art-Net to DMX, which means that you can connect the first device
to your computer using a CAT-5/CAT-6 cable and the rest of the devices can be linked using a DMX
cable. For more information, see 3. Run Mode on page 28.

16
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Multiple Polars (Wireless DMX Control)
01) Install multiple Polars at the desired positions (maximum distance to transceiver: 250 m).
02) In order for the Polars to receive a wireless DMX signal properly, activate W-DMX on all Polars (see
4.4. Signal on page 31 for more information).
03) Pair the wireless signal transmitter with multiple Polars. In order to create a wireless connection,
please read the manual of your wireless signal transmitter.
04) Use a DMX cable to connect the transmitter to a suitable light controller.
Fig. 10

17
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Sweden 2.4 GHz Wireless communication module
Communication distance:
Depending on the transmitting power or transmitter module
Test conditions:
W-DMX TRx Transmitter module, 2 dBi Antenna, transmitting power
20 dBm (100 mW)
Range indoor:
60 m (approx. through three concrete walls)
Range outdoor:
250 m
Wireless DMX Connection
The wireless receiving module “Nano G5 Receiver, 2.4 GHz”, provided by the Swedish WIRELESS
SOLUTION, only has a 2.4 GHz wireless signal receiving function. In order to match the wireless signal,
please use the 50175 W-DMX MicroBox F-1 G5 Transceiver by WIRELESS SOLUTION.
The Polar cannot receive a wireless DMX signal and a DMX cable signal at the same time.
Connect the Polar to the Wireless DMX Signal Transmitter
Enable W-DMX for the device and select the W-DMX option as control mode. See 4.4. Signal on page 31
for more information.
The Polar cannot actively match a random wireless signal transmitter.
In order to create a wireless match, please check the manual of your wireless signal transmitter.
We advise you to use the W-DMX MicroBox F-1 G5 Transceiver (50175) by WIRELESS SOLUTION (Fig. 11).
Fig. 11
Disconnect the Polar from the Wireless DMX Signal Transmitter
To turn W-DMX off, disable W-DMX by unlinking the fixture. See 4.4. Signal on page 31 for more
information. The Polar will now be disconnected.

18
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
Connecting to a Network
Art-Net Settings
01) Install any Art-Net-based software on your PC (Windows or Mac) or use a light controller which
supports Art-Net.
02) Connect the power supply to the Polar.
03) Connect the device’s RJ45 connector to the RJ45 connector of the lighting controller/network
switch, using a CAT-5/CAT-6 cable.
04) Set the IP address of your computer/light controller to 2.x.x.x or 10.x.x.x, depending on the Art-Net
settings. See 4.3. Network on page 30 for more information.
05) Set the Subnet mask to 255.0.0.0. on all devices.
06) Make sure that all fixtures in the network have a unique IP address.
07) If you want to connect more fixtures, follow the example below.
Example:
01) Make sure that each connected Polar has a unique IP address.
02) Make sure that the subnet mask on each device is set to 255.0.0.0.
03) Set the universe of the first Polar to 1.
04) Set the first Polar’s DMX address to 001.
05) Please note, that you can connect only 18 devices (18 x 28 channels = 504 channels needed). Due
to the channel limit of 512, you cannot connect the 19th device to the same data line, as it would
result in limited functionality of this device.
06) In order to solve this problem, set the universe of the 19th Polar to 2 and its DMX address to 001.
07) When connecting multiple devices, you can repeat steps 5 and 6 up to 255 times, each time
inserting ascending universe numbers (as there are 255 universes available).
08) Map all connected devices.
09) The connected Polars are now ready for use.
10) When creating large setups, it is recommended to use a 16-bit, high speed Ethernet switch to
distribute the Art-Net data signal.
Art-Net is a protocol that uses TCP/IP to transfer large amount of DMX-512 data over an Ethernet network.
Art-Net 4 can support up to 32768 universes. Art-Net™ Designed by and Copyright Artistic Licence
Holdings Ltd.
sACN Settings
01) Connect the device’s RJ45 connector to a network switch, using a CAT-5/CAT-6 cable.
02) Set the IP address of your computer/lighting controller. sACN networks have no restrictions on the IP
address.
03) Set the Subnet mask on all devices.
04) Make sure that all fixtures in the network have a unique IP address.
sACN (streaming Architecture for Control Networks), also known as ANSI E1.31, is a protocol for sending
DMX-512 data over IP networks developed by ESTA (Entertainment Services and Technology Association).
It supports up to 63999 universes and uses multicasting.

19
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
How to Make a Data Cable
A standard ETHERNET cable can be used to replace the data cable required to transmit the data.
Please follow the instructions below in order to create an extra network cable.
Take a standard network cable (CAT-5/ 5E /6) and connect it to the RJ45 connector, as shown on Fig. 12.
The wires should now be colored as follows:
Fig. 12