Show Tec Polar Wash 740 User manual

USER MANUAL
ENGLISH
V1.0
Polar Wash 740
Product code: 40106
cc c

Preface
Thank you for purchasing this Showtec product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be
stored at an easily accessible location.
This user manual contains information concerning:
• Safety instructions•
• Intended and non-intended use of the device•
• Installation and operation of the device•
• Maintenance procedures•
• Troubleshooting•
• Transport, storage and disposal of the device•
Non-observance of the instructions in this user manual may result in serious injuries and damage of property.
©2023 Showtec. All rights reserved.
No part of this document may be copied, published or otherwise reproduced without the prior written consent
of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document or other language versions, please visit our website www.highlite.com or
contact us at [email protected].
Highlite International and its authorized service providers are not liable for any injury, damage, direct or indirect
loss, consequential or economic loss or any other loss arising from the use of, or inability to use or reliance on
the information contained in this document.
1
cProduct code: 40106
Polar Wash 740

Table of contents
1. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. Before Using the Product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2. Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3. LEDs Lifespan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4. Text Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.5. Symbols and Signal Words. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.6. Symbols on the Information Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1. Warnings and Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2. Requirements for the User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3. Description of the Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1. Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2. Back View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.3. Base Plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.4. Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.5. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4. Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.1. Safety Instructions for Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2. Personal Protective Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.3. Installation Site Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.4. Rigging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.5. Connecting to Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.6. Power Linking of Multiple Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5. Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1. Warnings and Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2. Stand-alone Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.3. DMX Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.3.1. DMX-512 Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.3.2. DMX Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.3.3. DMX Linking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3.4. DMX Addressing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6. Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.1. Safety Instructions for Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.2. Control Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.3. Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.4. Start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.5. No Reset Start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.6. Menu Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.7. Main Menu Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.7.1. DMX Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.7.2. Person (DMX Channel Mode). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.7.3. Run Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.7.4. Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.7.4.1. Display Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.7.4.2. Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.7.4.3. Signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.7.4.4. Color Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.7.5. Edit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.7.6. Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.7.6.1. Channel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.7.6.2. Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.7.7. Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.7.8. Info. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.7.8.1. System Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.8. DMX Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.8.1. DMX Channels Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.8.2. SSP (19 Channels), TOUR (21 Channels), TR16 (28 Channels). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2
cProduct code: 40106
Polar Wash 740

6.8.3. CMY (22 Channels). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
6.8.4. HSIC (21 Channels). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
6.8.5. PIXEL (25 Channels). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
6.8.6. Beam LEDs Zone Numbering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6.8.7. Beam Color Presets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
6.9. RDM Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
6.9.1. RDM Details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
6.9.2. Supported RDM PIDs (Parameter IDs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
7. Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
8. Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
8.1. Safety Instructions for Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
8.2. Preventive Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
8.2.1. Basic Cleaning Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
8.3. Corrective Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
8.3.1. Replacing the Fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
8.3.2. Draining Condensation Water. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
9. Deinstallation, Transportation and Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
9.1. Instructions for Deinstallation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
9.2. Instructions for Transportation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
9.3. Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
10. Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
11. Approval. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3
cProduct code: 40106
Polar Wash 740

1. Introduction
1.1. Before Using the Product
Important
Read and follow the instructions in this user manual before installing, operating or servicing
this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite
International dealer.
Your shipment includes:
Figure 1
• Showtec Polar Wash 740•
• Schuko to Power Pro True cable (1,5 m)•
• 2 x quick-lock brackets•
• User manual•
1.2. Intended Use
This device is intended for professional use as a moving head wash light. It can be installed indoors and
outdoors. This device is not suitable for households and for general lighting.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
1.3. LEDs Lifespan
The light output of the LEDs gradually decreases over time (lumen depreciation). High operating temperatures
contribute to this process. You can extend the lifespan of the LEDs by providing adequate ventilation and
operating the LEDs at the lowest possible brightness.
1.4. Text Conventions
Throughout the user manual the following text conventions are used:
• Buttons: All buttons are in bold lettering, for example "Press the UP/DOWN buttons"•
• References: References to parts of the device are in bold lettering, for example: "turn the adjustment•
handle (05)". References to chapters are hyperlinked
• 0–255: Defines a range of values•
• Notes: Note: (in bold lettering) is followed by useful information or tips•
4
cProduct code: 40106
Polar Wash 740

1.5. Symbols and Signal Words
Safety notes and warnings are indicated throughout the user manual by safety signs.
Always follow the instructions provided in this user manual.
DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION Indicates a potentially hazardous situation, which, if not avoided, may result in minor or
moderate injury.
Attention Indicates important information for the correct operation and use of the product.
Important Read and observe the instructions in this document.
Electrical hazard
Eye damage hazard
Provides important information about the disposal of this product.
1.6. Symbols on the Information Label
This product is provided with an information label. The information label is located on the base plate of the
device.
The information label contains the following symbols:
This device shall not be treated as household waste.
Read and follow the instructions in the user manual before installing, operating or servicing the
device.
This device falls under IEC protection class I.
This devices is rated IP65.
Minimum distance from lighted objects
Minimum distance from other objects
5
cProduct code: 40106
Polar Wash 740

2. Safety
Important
Read and follow the instructions in this user manual before installing, operating or servicing
this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual.
2.1. Warnings and Safety Instructions
DANGER
Danger for children
For adult use only. The device must be installed beyond the reach of children.
• Do not leave any parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within the reach of•
children. Packaging material is a potential source of danger for children.
DANGER
Electric shock caused by dangerous voltage inside
There are areas inside the device where dangerous touch voltage (> 120 V DC) may be present.
• Do not open the device or remove any covers.•
• Do not operate the device if the covers or the housing are open. Before operation, check if the housing is•
firmly closed and all screws are tightly fastened.
• Disconnect the device from the electrical power supply before service and maintenance, and when the•
device is not in use.
DANGER
Electric shock caused by short-circuit
This device falls under IEC protection Class I.
• Make sure that the device is electrically connected to ground (earth). Connect the device only to a•
socket-outlet with a ground (earth) connection.
• Do not cover the ground (earth) connection.•
• Do not bypass the thermostatic switch or fuses.•
• Replace fuses only with same type and rating.•
• Do not let the power cable come into contact with other cables. Handle the power cable and all•
connections with the mains with caution.
• Do not modify, bend, mechanically strain, put pressure on, pull or heat up the power cable.•
• Make sure that the power cable is not crimped or damaged. Examine the power cable periodically for any•
defects.
• Do not immerse the device in water or other liquids. Do not install the device in a location where flooding•
may occur.
• Do not use the device during thunderstorms. Disconnect the device from the electrical power supply•
immediately.
• Keep the connectors sealed with the rubber caps when the connectors are not in use.•
• Do not connect the cables from above the connectors, if the device is installed outdoors. Make a ‘drip•
loop’ in the cable so that rain water cannot enter the device.
6
cProduct code: 40106
Polar Wash 740

WARNING
Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at strobe
lights.
CAUTION
Possible eye damage caused by high light intensity
Possibly hazardous optical radiation emitted from this device. This is a Risk Group 2 product according to
EN62471. The device should be positioned so that prolonged staring into the light source at a distance closer
than 2,5 m is not expected.
• Do not stare at operating lamp. May be harmful to the eye.•
• Do not look at the light source with optical instruments that may concentrate the light output.•
• Make sure that persons are not looking directly into the light source when the device lights up suddenly. This•
can happen when the device is powered on, when it receives a DMX signal, or when certain menu items
are selected.
• Disconnect power before servicing.•
CAUTION
Risk of injury due to movement of the device
The head of the device can move quickly. Persons staying near the device could get injured or scared.
• Make sure that there are no persons close to the device when you turn on the device and during•
operation.
• Keep body parts away from the moving parts of the device when servicing and during maintenance. Long•
hair or loose clothing can be entangled during the rotation of the moving head.
Attention
Power supply
• Before connecting the device to the power supply, make sure that the current, voltage and frequency•
match the input voltage, current and frequency specified on the information label on the device.
• Make sure that the cross-sectional area of the extension cords and power cables is sufficient for the•
required power consumption of the device.
Attention
General safety
•Do not lift the device holding it by the projector head. This may damage the mechanics. Use the transport •
handles when handling the device.
•Do not insert objects into air vents. •
•Do not connect this device to a dimmer pack. •
•Do not switch the device on and off in short intervals. This reduces the device’s life. •
•Do not shake the device. Avoid brute force when installing or operating the device. •
•Change the lens or the LEDs if they are visibly damaged to such an extent that their effectiveness is •
impaired, for example by cracks or deep scratches.Contact your Highlite International dealer for more
information, as servicing can be performed only by instructed or skilled persons.
•If the device is dropped or struck, disconnect the device from the electrical power supply immediately. •
7
cProduct code: 40106
Polar Wash 740

• If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it on•
immediately. Let the device reach room temperature before switching it on, otherwise it may be damaged
by the formed condensation.
• If the device fails to work properly, discontinue the use immediately.•
Attention
For professional use only
This device must be used only for the purposes it is designed for.
This device is intended for professional use as a moving head wash light. Any incorrect use may lead to
hazardous situations and result in injuries and material damage.
• This device is not suitable for households and for general lighting.•
• This device is not designed for permanent operation.•
• This device does not contain user-serviceable parts. Unauthorized modifications to the device will render•
the warranty void. Such modifications may result in injuries and material damage.
Attention
Before use, examine the device visually for any defects.
Make sure that:
• All screws used for installing the device or parts of the device are tightly fastened and are not corroded.•
• The safety devices are not damaged.•
• There are no deformations on housings, fixings and installation points.•
• The lens is not cracked or damaged.•
• The power cables are not damaged and do not show any material fatigue.•
Attention
Do not expose the device to conditions that exceed the rated IP class conditions.
This device is IP65 rated. IP (Ingress Protection) 65 class means that the device is dust-tight and protected
against harmful effect of water jets.
Keep the connectors sealed with the rubber caps when the connectors are not in use.
2.2. Requirements for the User
This product may be used by ordinary persons. Maintenance may be carried out by ordinary persons.
Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite
International dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled person,
for specific tasks and work activities associated with the installation, service and maintenance of this product,
so that they can identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and avoid hazards
associated with the installation, service and maintenance of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons include not
only users of the product but also any other persons that may have access to the device or who may be in the
vicinity of the device.
8
cProduct code: 40106
Polar Wash 740

3. Description of the Device
The Showtec Polar Wash 740 is a compact LED wash moving head with zoom and LED ring effects, suitable for
indoor and outdoor applications. With the addition of the lime LED, it achieves a CRI of 85 for its white colors.
The device features a motorized zoom from 3,5° up to 44°. The 7 RGBL LEDs can be controlled in 2 sections: the
center LED and the outer LEDs. The LED ring around the 7 LEDs can be controlled separately.
3.1. Front view
Figure 2
LED ring
7 x LED modules x 40 W (RGBL)
2 x Transport handles
Control panel: OLED display and control
buttons
9
cProduct code: 40106
Polar Wash 740
01)
02)
03)
04)

3.2. Back View
Figure 3
Protective vent (M12x1,5)
IP65-rated 3-pin DMX signal connector IN
IP65-rated 3-pin DMX signal connector OUT
IP65-rated 5-pin DMX signal connector IN
IP65-rated 5-pin DMX signal connector OUT
Fuse (T 6,3 A, 250 V)
IP65-rated Seetronic power connector IN
IP65-rated USB-C connector (this is used for
servicing to update firmware)
IP65-rated Seetronic power connector OUT
Drain plug
3.3. Base Plate
Figure 4
4 x Mounting holes for quick-lock brackets
2 x Openings for a safety cable
10
cProduct code: 40106
Polar Wash 740
05)
06)
07)
08)
09)
10)
11)
12)
13)
14)
15)
16)

3.4. Product Specifications
Model: Polar Wash 740
Source:
Light source type LED
Light source quantity 7
Light source power 40W
LED color type R / G / B / L
Refresh rate (min.) 1200Hz
Refresh rate (max.) 25kHz
Illuminance @ 2 m 73388lx
Illuminance @ 3 m 32617lx
Illuminance @ 5 m 11742lx
Luminous flux (total) 4060lm
Luminous flux (red) 1093lm
Luminous flux (green) 1604lm
Luminous flux (blue) 679lm
Luminous flux (lime) 1800lm
CRI 85
Optical:
Beam angle min. (circular) 3,5°
Beam angle max. (circular) 44°
Zoom type Motorized
Zoom ratio 1:10
Zoom minimum 3,5°
Zoom maximum 44°
Control and Programming:
Control mode DMX
DMX channels HSIC (21 CH), SSP (19 CH), Tour (21CH), TR16 (28CH), Pixel (25CH),
CMY(22CH)
Protocols DMX / RDM
Wireless Optional
Display OLED
Fan mode Yes
Zone control (sections) 2sections
Dimmer resolution 16 bit
Dynamic Effects:
Dimmer 0–100 %
Strobe 0–25 Hz
Movement:
Pan 540°
Tilt 220°
Pan/Tilt resolution 16-bit
Continuous movement No
Electrical Specifications and Connections:
Power supply 100–240 V AC 50–60 Hz
Power consumption 320W
Fuse 6,3A
11
cProduct code: 40106
Polar Wash 740

Power connector IN Power Pro True
Power connector OUT Power Pro True
DMX connector IN XLR 3P / XLR 5P
DMX connector OUT XLR 3P / XLR 5P
Mechanical Specifications:
Length (mm) 290mm
Width (mm) 233mm
Height (mm) 375mm
Weight 9,8kg
Noise level maximum 45,2dB
Silent mode noise level 36,1dB
IP Rating IP65
Housing Aluminium die-cast
Color Black
Product Properties:
Cooling Convection/Axial fan
Rigging:
Mounting options Quick-Lock
Safety attachment Yes
Safety eyes 1
Thermal Specifications:
Maximum ambient temperature 45°C
Maximum surface temperature 65°C
Minimum operating temperature -20°C
Included Items:
Included cables Power Pro True Cable 
Included rigging Quick-Lock Bracket
12
cProduct code: 40106
Polar Wash 740

3.5. Dimensions
Figure 5
4. Installation
4.1. Safety Instructions for Installation
WARNING
Incorrect installation can cause serious injuries and damage of property.
If trussing systems are used, installation must be carried out only by instructed or skilled persons.
Follow all applicable European, national and local safety regulations concerning rigging and trussing.
13
cProduct code: 40106
Polar Wash 740

4.2. Personal Protective Equipment
During installation and rigging wear personal protective equipment in compliance with the national and site-
specific regulations.
4.3. Installation Site Requirements
• The device can be used indoors and outdoors.•
• The minimum distance between the light output and the illuminated surface must be bigger than2 m.•
• The minimum distance to other objects must be bigger than 0,5 m.•
• The maximum ambient temperature ta = 40 °C must never be exceeded.•
4.4. Rigging
The device can be positioned on a flat surface or mounted to a truss or other rigging structure in any
orientation. Make sure that all loads are within the pre-determined limits of the supporting structure.
CAUTION
Restrict the access under the work area during rigging/derigging.
To mount the device, follow the steps below:
01) Fasten the 2 quick-lock brackets, supplied with the device, on the mounting holes for quick-lock01)
brackets(15). You can position the quick-lock brackets in two ways.
02) Install the clamps. Make sure that you use clamps suitable for attaching the device to a truss.02)
Figure 6
03) Attach the device to the supporting structure. Make sure that the device cannot move freely.03)
04) Secure the device with a secondary suspension, for example a safety cable. Make sure that the secondary04)
suspension can hold 10 times the weight of the device. If possible, the secondary suspension should be
attached to a supporting structure independent of the primary suspension. Put the safety cable through
the openings for a safety cable (16).
14
cProduct code: 40106
Polar Wash 740

4.5. Connecting to Power Supply
DANGER
Electric shock caused by short-circuit
The device accepts AC mains power at 100–240 V and 50/60 Hz. Do not supply power at any other voltage or
frequency to the device.
This device falls under IEC protection class I. Make sure that the device is always electrically connected to the
ground (earth).
Before connecting the device to the socket-outlet:
•Make sure that the power supply matches the input voltage specified on the information label on the •
device.
•Make sure that the socket-outlet has ground (earth) connection. •
Connect the device to the socket-outlet with the power plug. Do not connect the device to a dimmer circuit,
as this may damage the device.
This device is IP65 rated.
• Do not expose the device to conditions that exceed the rated IP class conditions.•
• Keep the connectors sealed with the rubber caps when the connectors are not in use.•
• Do not connect the cables from above the connectors, if the device is installed outdoors. Make a ‘drip•
loop’ in the cable so that rain water cannot enter the device.
• Make sure that the cable run is not too heavy. A heavy cable run can cause damage to the connectors. If•
the connectors are damaged, their ingress protection (IP) can deteriorate.
4.6. Power Linking of Multiple Devices
This device supports power linking. Power can be relayed to another device via the power OUT connector.
Note that the input and the output connectors have different designs: one type cannot be connected to the
other.
Power linking of multiple devices must be carried out only by instructed or skilled persons.
WARNING
Incorrect power linking may lead to overload of the electrical circuit and result in serious
injuries and damage of property.
To prevent overload of the electrical circuit, when power linking multiple devices:
• Use cables with sufficient current-carrying capacity. The power cable supplied with the device is not•
suitable for power linking of multiple devices.
• Make sure that the total current draw of the device and all connected devices does not exceed the rated•
capacity of the power cables and the circuit breaker.
• Do not link more devices on one power link than the maximum recommended number.•
Maximum recommended number of devices:
• at 100–120 V: 4 devices Polar Wash 740•
• at 200–240 V: 9 devices Polar Wash 740•
15
cProduct code: 40106
Polar Wash 740

5. Setup
5.1. Warnings and Precautions
DANGER
Electric shock caused by short-circuit
This device is IP65 rated.
• Do not expose the device to conditions that exceed the rated IP class conditions.•
• Keep the connectors sealed with the rubber caps when the connectors are not in use.•
• Do not connect the cables from above the connectors, if the device is installed outdoors. Make a ‘drip•
loop’ in the cable so that rain water cannot enter the device.
• Make sure that the cable run is not too heavy. A heavy cable run can cause damage to the connectors. If•
the connectors are damaged, their ingress protection (IP) can deteriorate.

Attention
Connect all data cables before supplying power.
Disconnect power supply before connecting or disconnecting data cables.
5.2. Stand-alone Setup
When the Polar Wash 740 is not connected to a controller or to other devices, it functions as a stand-alone
device. It can be operated manually via the control panel or in auto mode.
For more information refer to Control Modes (see 6.2. Control Modes on page 19).
5.3. DMX Connection
5.3.1. DMX-512 Protocol
You need a DMX serial data link to run light shows of one or more devices using a DMX-512 controller.
The Polar Wash 740 has 3-pin and 5-pin DMX signal IN and OUT connectors.
The pin assignment is as follows:
•3-pin: pin 1 (ground), pin 2 (-), pin 3 (+) •
•5-pin: pin 1 (ground), pin 2 (-), pin 3 (+), pin 4 (N/C), pin 5 (N/C) •
Devices on a serial data link must be daisy-chained in a single line. The number of devices that you can control
on one data link is limited by the combined number of the DMX channels of the connected devices and the
512 channels available in one DMX universe.
To comply with the TIA-485 standard, no more than 32 devices should be connected on one data link. Inorder
to connect more than 32 devices on one data link, you must use a DMX optically isolated splitter/booster,
otherwise this may result in deterioration of the DMX signal.
Note:
•Maximum recommended DMX data link distance: 300 m •
•Maximum recommended number of devices on a DMX data link: 32 devices •
5.3.2. DMX Cables
Shielded twisted-pair cables with 3-pin/5-pin XLR connectors must be used for reliable DMX connection. You
can purchase DMX cables directly from your Highlite International dealer or make your own cables.
If you use XLR audio cables for DMX data transmission, this may lead to signal degradation and unreliable
operation of the DMX network.
16
cProduct code: 40106
Polar Wash 740

When you make your own DMX cables, make sure that you connect the pins and wires correctly as shown in
the figure below.
Figure 7
5.3.3. DMX Linking
To connect multiple devices on one DMX data link, follow the steps below:
01) Use a 3-pin/5-pin DMX cable to connect the DMX OUT connector of the lighting controller to the DMX IN01)
connector of the 1st device.
02) Connect the DMX OUT connector of the 1st device to the DMX IN connector of the 2nd device with a 3-02)
pin/5-pin DMX cable.
03) Repeat step 2 to connect all devices in a daisy-chain.03)
04) Connect a DMX terminator (120 Ω resistor) to the DMX OUT connector of the last device on the data link.04)
Figure 8
17
cProduct code: 40106
Polar Wash 740

5.3.4. DMX Addressing
In a setup with multiple devices, make sure that you set the DMX starting address of each device correctly. The
Polar Wash 740 has 6 personalities: HSIC (21 channels), SSP (19 channels), Tour (21 channels), TR16 (28
channels), CMY (22 channels), Pixel (25 channels).
If you want to connect multiple devices on one data link and use them in 28-channel mode, for example,
follow the steps below:
01) Set the starting address of the 1st device on the data link to 1 (001).01)
02) Set the starting address of the 2nd device on the data link to 29 (029), as 1 + 28 = 29. 02)
03) Set the starting address of the 3rd device on the data link to 57 (057) as 29 + 28 = 57. 03)
04) Continue assigning the starting addresses of the remaining devices by adding each time 28 to the previous 04)
number.
Make sure that you do not have any overlapping channels in order to control each Polar Wash 740 correctly. If
two or more devices are addressed similarly, they will work similarly.
18
cProduct code: 40106
Polar Wash 740

6. Operation
6.1. Safety Instructions for Operation
Attention
This device must be used only for the purposes it is designed for.
This device is intended for professional use as a moving head wash light. It can be installed indoors and
outdoors. This device is not suitable for households and for general lighting.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Attention
Power supply
Before connecting the device to the power supply, make sure that the current, voltage and frequency match
the input voltage, current and frequency specified on the information label on the device.
6.2. Control Modes
The Polar Wash 740 supports the following control modes:
• Stand-alone: Auto operation mode (built-in program, custom programs), manual operation•
• DMX-512: HSIC (21 channels), SSP (19 channels), Tour (21 channels), TR16 (28 channels), CMY (22•
channels), Pixel (25 channels)
For more information about how to connect the devices, refer to Setup (see 5. Setup on page 16).
To operate the device manually as a stand-alone device:
Adjust the parameters of the device in the Channel submenu (see 6.7.6.1. Channel on page 32).
To run the built-in program or one of the custom programs in auto operation mode without a DMX controller:
Select the control mode of the device in the Run Mode menu (see 6.7.3. Run Mode on page 27).
• If you select AUTO, the device will run the built-in program.•
• If you select CUSTOM 1 or CUSTOM 2, the device will run the respective custom program. You can edit the•
custom programs in the Edit menu (see 6.7.5. Edit on page 30).
To operate the device with a DMX controller:
01) Select DMX512 as control mode in the Run Mode menu (see 6.7.3. Run Mode on page 27).01)
02) Set the DMX starting address (see 5.3.4. DMX Addressing on page 18) of the device in the DMX Address02)
menu (see 6.7.1. DMX Address on page 27).
03) Select the DMX channel mode in the DMX channel mode menu (see 6.7.2. Person (DMX Channel Mode)03)
on page 27). Refer to DMX Channels (see 6.8. DMX Channels on page 35) for a complete overview of all
DMX channels.
Note:
The device can be fitted with a wireless module and controlled via wireless DMX. Contact your Highlite
International dealer for more information.
19
cProduct code: 40106
Polar Wash 740