Show Tec Compact Par 18 MKII Tour V1 User manual

Compact Par 18 MKII Tour V1
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 42596
MANUAL
ENGLISH

1
Ordercode: 42596
Compact Par 18 MKII Tour
Table of contents
Warning ...............................................................................................................................................................................2
Safety Instructions .........................................................................................................................................................2
Operating Determinations ..........................................................................................................................................4
Rigging ............................................................................................................................................................................4
Connection with the mains.........................................................................................................................................5
Return Procedure..........................................................................................................................................................5
Claims..............................................................................................................................................................................5
Description of the device.................................................................................................................................................6
Overview ........................................................................................................................................................................6
Frontside..........................................................................................................................................................................7
Backside .........................................................................................................................................................................8
Installation...........................................................................................................................................................................8
Set Up and Operation .......................................................................................................................................................8
Control Modes...............................................................................................................................................................9
One Compact Par (Auto, Built-in programs, Sound-controlled, Manual) ......................................................9
Multiple Compact Pars (Master/Slave control) ...................................................................................................9
Multiple Compact Pars (DMX Control)...................................................................................................................10
Fixture Linking...............................................................................................................................................................11
Data Cabling...............................................................................................................................................................11
Control Panel ...............................................................................................................................................................12
Control Mode ..............................................................................................................................................................12
DMX Addressing ..........................................................................................................................................................12
Menu Overview...........................................................................................................................................................13
Main Menu Options....................................................................................................................................................14
1. Auto Run................................................................................................................................................................14
2. Built-in Programs...................................................................................................................................................14
3. Slave Mode...........................................................................................................................................................14
4. DMX Mode ............................................................................................................................................................15
5. Sound-controlled Mode .....................................................................................................................................15
6. Dimmer Options (Manual) .................................................................................................................................15
7. Settings...................................................................................................................................................................15
8. System Information..............................................................................................................................................15
DMX Channels .............................................................................................................................................................16
1 Channel..................................................................................................................................................................16
3 Channels ................................................................................................................................................................16
4 Channels ................................................................................................................................................................16
6 Channels ................................................................................................................................................................17
Maintenance....................................................................................................................................................................18
Troubleshooting ...............................................................................................................................................................18
No Light.........................................................................................................................................................................18
No Response to DMX..................................................................................................................................................18
Restore Factory Settings ............................................................................................................................................18
Product Specification .....................................................................................................................................................20
Dimensions........................................................................................................................................................................21

2
Ordercode: 42596
Compact Par 18 MKII Tour
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
Showtec Compact Par 18 MKII Tour
PowerCON power cable 1,5 m
User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving your lifespan expectancy is of a higher priority, place care in providing
for lower operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
be qualified
follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.

3
Ordercode: 42596
Compact Par 18 MKII Tour
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never place any material over the lens.
Never look directly into the light source.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not connect this device to a dimmerpack.
Do not switch the device on and off in short intervals, as this would reduce the device’s life.
Do not touch the device’s housing bare-handed during its operation. Allow the fixture to cool for at
least 5 minutes before handling.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoors, avoid contact with water or other liquids.
Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
Only operate the device after having familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Always keep case closed while operating.
Always allow free air space of at least 50 cm around the unit for ventilation.
Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power-cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power cord is never crimped or damaged. Check the device and the power-
cord from time to time.
If the lens is obviously damaged, it has to be replaced. So that its functions are not impaired, due to
cracks or deep scratches.
If device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
For adult use only. Device must be installed out of the reach of children. Never leave the unit running
unattended.
Never attempt to bypass the thermostatic switch or fuses.
For replacement use fuses of same type and rating only.
The user is responsible for correct positioning and operating of the Compact Par 18 MKII Tour. The
manufacturer will not accept liability for damages caused by the misuse or incorrect installation of
this device.
This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
Repairs, servicing and electric connection must be carried out by a qualified technician.
WARRANTY: Till one year after date of purchase.

4
Ordercode: 42596
Compact Par 18 MKII Tour
Operating Determinations
This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
The minimum distance between light output and the illuminated surface must be more than 1 meter.
The maximum ambient temperature ta = 35°C must never be exceeded.
The relative humidity must not exceed 50 % with an ambient temperature of 35° C.
If this device is operated in any other way, than the one described in this manual, the product may
suffer damages and the warranty becomes void.
Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself!
Always let the installation be carried out by an authorized dealer!
Procedure:
If the Compact Par 18 MKII Tour is lowered from the ceiling or high joists, professional trussing systems
have to be used.
Use a clamp to mount the Compact Par 18 MKII Tour, with the mounting-bracket, to the trussing
system.
The Compact Par 18 MKII Tour must never be fixed swinging freely in the room.
The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
When rigging, derigging or servicing the Compact Par 18 MKII Tour, always make sure, that the area
below the installation place is blocked and staying in the area is forbidden.
The Compact Par 18 MKII Tour can be placed on a flat surface or fitted to any kind of truss with a clamp.
Improper installation can cause serious damage to people and property!

5
Ordercode: 42596
Compact Par 18 MKII Tour
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.

6
Ordercode: 42596
Compact Par 18 MKII Tour
Description of the device
Features
The Showtec Compact Par 18 MKII Tour is a compact and powerful parcan with high output and great
effects.
Input voltage: 100-240V AC, 60/50Hz
LED quantity: 18 x 3W 3-in-1 RGB LEDs
Power consumption: 60W
Channel modes: 1, 3, 4, 6 channels
Color mixing: RGB
Lumen: 2323
Light output: 3112 lux @ 2 m
IP rating: IP20
Housing: Die-cast aluminum
DMX control: via standard DMX controller
Onboard: Display for easy setup
Control: Auto, Built-in programs, Sound-controlled, Manual color, Master/Slave, DMX-512
Beam Angle: 28°
Dimmer: 0-100%
Strobe: 0-20Hz
Connections: PowerCON power connector IN/OUT & 3-pin DMX connector IN/OUT
Cooling: Convection
Dimensions: 264 x 93 x 295 mm (LxWxH)
Weight: 2,9 kg
Overview
Fig. 01

7
Ordercode: 42596
Compact Par 18 MKII Tour
Frontside
Fig. 02
01) Mounting bracket with inclination screw
02) Adjustment screw
03) 18 x 3W 3-in-1 RGB LEDs

8
Ordercode: 42596
Compact Par 18 MKII Tour
Backside
Fig. 03
04) LED display + menu buttons
05) 3-pin DMX signal connector OUT
06) 3-pin DMX signal connector IN
07) Safety eye
08) Ground/earth connection
09) 100-240V PowerCON power connector IN
10) 100-240V PowerCON power connector OUT
Installation
Remove all packing materials from the Compact Par 18 MKII Tour. Check that all foam and plastic
padding is removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.

9
Ordercode: 42596
Compact Par 18 MKII Tour
Control Modes
There are 6 modes:
Auto
Built-in programs
Sound-controlled
Manual
Master/slave
DMX-512 (1CH, 3CH, 4CH, CH6)
One Compact Par (Auto, Built-in programs, Sound-controlled, Manual)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Compact Par 18 MKII Tour is not connected with a DMX cable, it functions as a stand-
alone device.
05) Please see pages 14-15 for more information about Auto, Built-in programs, Sound-controlled and
Manual control functions.
Multiple Compact Pars (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Compact Pars.
The pins:
1. Earth
2. Signal (-)
3. Signal (+)
05) Link the units as shown in fig. 04. Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units. You can
use the same functions on the master device as described on pages 14-15 (Auto, Built-in programs,
Sound-controlled and Manual). This means that you can set your desired operation mode on the
master device and all slave devices will react the same as the master device.
Multiple Compact Pars (Master/Slave control)
Fig. 04

10
Ordercode: 42596
Compact Par 18 MKII Tour
Multiple Compact Pars (DMX Control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Compact Par 18 MKII Tour and other devices.
05) Link the units as shown in fig. 05. Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units.
06) Supply electric power: Plug electric mains power cords into each unit's PowerCON socket, then plug
the other end of the mains power cord into proper electric power supply sockets, starting with the
first unit. Do not supply power before the whole system is set up and connected properly.
Multiple Compact Pars DMX Set Up
Fig. 05
Note : Link all cables before connecting electric power

11
Ordercode: 42596
Compact Par 18 MKII Tour
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy chained in one single line. To comply with the
EIA-485 standard no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of Compact Pars on a DMX data link: 30 fixtures
Maximum recommended number of Compact Pars on a Power link: 11 fixtures @110V
Maximum recommended number of Compact Pars on a Power link: 21 fixtures @240V
Data Cabling
To link fixtures together you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
•DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin.
Ordercode FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
•DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
•DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
The Compact Par 18 MKII Tour can be operated with a controller in control mode or without the
controller in stand-alone mode.

12
Ordercode: 42596
Compact Par 18 MKII Tour
Control Panel
A)
B)
C)
D)
E)
LED display
Down button
Up button
Setup button
Mode button
Fig.06
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address the next time.)
DMX Addressing
The control panel on the front side of the base allows you to assign the DMX fixture address, which is the
first channel from which the Compact Par 18 MKII Tour will respond to the controller.
Please note when you use the controller, the unit has 6channels.
When using multiple Compact Pars, make sure you set the DMX addresses right.
Therefore, the DMX address of the first Compact Pars should be 1(001); the DMX address of the second
Compact Par 18 MKII Tour should be 1+6=7 (007); the DMX address of the third Compact Par 18 MKII Tour
should be 7+6=13 (013), etc.
Please, be sure that you don’t have any overlapping channels in order to control each Compact Par 18
MKII Tour correctly. If two or more Compact Pars are addressed similarly, they will work similarly.
Controlling:
After having addressed all Compact Par 18 MKII Tour fixtures, you may now start operating these via your
lighting controller.
Note: After switching on, the Compact Par 18 MKII Tour will automatically detect whether DMX 512 data
is received or not. If there is no data received at the DMX-input, the “LED“ on the control panel will not
flash.
The problem may be:
•The XLR cable from the controller is not connected with the input of the Compact Par 18 MKII Tour.
•The controller is switched off or defective, the cable or connector is defective, or the signal wires are
swapped in the input connector.
Note: It’s necessary to insert a XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
Display Off after 60 seconds
When no button is pressed for 60 seconds, the display will turn off.
To light up the display, you have to press the MODE, SETUP, UP or DOWN button.
Once you have pressed the button, the display will light up.

13
Ordercode: 42596
Compact Par 18 MKII Tour
Menu Overview

14
Ordercode: 42596
Compact Par 18 MKII Tour
Main Menu Options
1. Auto Run
2. Built in Programs
3. Slave Mode
4. DMX Mode
5. Sound-controlled Mode
6. Dimmer Options (Manual)
7. Settings
8. System Information
1. Auto Run
With this menu you can start Auto Run mode.
01) Press the MODE button until the display shows .
02) The Compact Par will now run all the built-in programs in a sequence.
2. Built-in Programs
With this menu you can you can set the built-in programs.
01) Press the MODE button until the display shows .
02) Press the SETUP button to open the menu.
03) Press the UP/DOWN buttons to toggle through the 9 built-in programs. The adjustment range is
between .
04) Once you have selected the desired program, press the SETUP button to open.
05) If you have chosen , press the UP/DOWN buttons to choose the desired color macro. The
available color macros are: Red, Green, Blue, Amber, Orange, Yellow, Purple, Pink, Cyan, Light Red,
Light Green, Light Blue, Warm White, Cold White, Black.
06) Press the SETUP button again to proceed to strobe settings.
07) Press the UP/DOWN buttons to set the strobe frequency. The adjustment range is between
, from low to high frequency.
08) Return to step 4. If you have chosen one of the programs , press the SETUP
button to enter the menu.
09) Repeatedly press the SETUP button to toggle between strobe and program speed settings.
10) Press the UP/DOWN buttons to adjust the values.
Program speed, from slow to fast
Strobe frequency, from low to high frequency
3. Slave Mode
With this menu you can set the device as a slave device.
01) Press the MODE button until the display shows .
02) If the device has not been set to slave, it is automatically classified as a master device. All slave
devices will follow the master. If the device has been set to slave, it will react the same as its master
device.

15
Ordercode: 42596
Compact Par 18 MKII Tour
4. DMX Mode
With this menu you can set the DMX address and the desired DMX channel mode.
01) Press the MODE button until the display shows .
02) Press the SETUP button to open the menu.
03) Press the UP/DOWN buttons to select the desired DMX address. The adjustment range is between
.
04) Press the SETUP button again to proceed to the channel mode selection.
05) Press the UP/DOWN buttons to choose one of the 4 channel modes: 1 channel, 3 channels, 4
channels, 6 channels.
5. Sound-controlled Mode
01) Press the MODE button until the display shows .
02) Press the SETUP button to open the menu.
03) Press the UP/DOWN buttons to set the sound sensitivity. The adjustment range is between
, from OFF to high sound sensitivity.
6. Dimmer Options (Manual)
With this menu you can manually set the desired color.
01) Press the MODE button until the display shows .
02) Press the SETUP button to open the menu.
03) Press the SETUP button to toggle through the 3 colors: Red, Green and Blue.
04) Press the UP/DOWN buttons to set the color brightness. The adjustment range is between 0-255, from
dark to brightest.
05) You can combine Red, Green and Blue to create an infinite range of colors (0-255).
7. Settings
01) Press the MODE button until the display shows .
02) Press the SETUP button to open the menu.
03) Press the UP/DOWN buttons to choose between the 2 available menus: and .
04) Press the SETUP button to open the desired menu.
05) In menu you can set how long the display will remain on, when no button is pressed.
06) Press the UP/DOWN buttons to choose between 10, 20, 30 or 60 seconds.
07) In menu you can restore the factory settings.
08) Press the SETUP button to open the menu and then press the SETUP buttons to confirm or the MODE
button to return to the previous menu.
09) The factory settings will now be restored.
8. System Information
01) Press the MODE button until the display shows .
02) Press the SETUP button to open the menu.
03) Press the UP/DOWN buttons to choose between the 2 menus: and .
04) Press the SETUP button to open the desired menu.
05) In menu, you can view the device’s current model number.
06) In the menu you can view the current software version.

16
Ordercode: 42596
Compact Par 18 MKII Tour
DMX Channels
1 Channel
Channel 1 –Color macros
0-17
Black
18-35
Red
36-53
Green
54-71
Blue
72-89
Amber
90-107
Orange
108-125
Yellow
126-143
Purple
144-161
Pink
162-179
Cyan
180-197
Light Red
198-215
Light Green
216-233
Light Blue
234-251
Warm White
252-255
Cold White
3 Channels
Channel 1 –Red dimmer intensity
0-255
Red, from 0 –100%
Channel 2 –Green dimmer intensity
0-255
Green, from 0 –100%
Channel 3 –Blue dimmer intensity
0-255
Blue, from 0 –100%
4 Channels
Channel 1 –Dimmer
0-255
From dark to brightest
Channel 2 –Red dimmer intensity ( Dimmer must be open )
0-255
Red, from 0 –100%
Channel 3 –Green dimmer intensity ( Dimmer must be open )
0-255
Green, from 0 –100%
Channel 4 –Blue dimmer intensity ( Dimmer must be open )
0-255
Blue, from 0 –100%

17
Ordercode: 42596
Compact Par 18 MKII Tour
6 Channels
Channel 1 –Dimmer
0-255
From dark to brightest
Channel 2 –Red dimmer intensity ( Dimmer must be open and CH6 must be set to 0 )
0-255
Red, from 0 –100%
Channel 2 –Color macros ( Dimmer must be open and CH6 must be set between 1-27 )
0-17
Black
18-35
Red
36-53
Green
54-71
Blue
72-89
Amber
90-107
Orange
108-125
Yellow
126-143
Purple
144-161
Pink
162-179
Cyan
180-197
Light Red
198-215
Light Green
216-233
Light Blue
234-251
Warm White
252-255
Cold White
Channel 2 –Program speed ( Dimmer must be open and CH6 must be set between 28-251 )
0-255
Program speed, from slow to fast
Channel 3 –Green dimmer intensity ( Dimmer must be open and CH6 must be set to 0 )
0-255
Green, from 0 –100%
Channel 4 –Blue dimmer intensity ( Dimmer must be open and CH6 must be set to 0 )
0-255
Blue, from 0 –100%
Channel 5 –Strobe ( Dimmer and CH2-4 must be open )
0-255
Strobe frequency, from low to high frequency
Channel 6 –Control modes
0
Manual mode
1-27
Color macros
28-251
Built-in programs
252-255
Sound-controlled

18
Ordercode: 42596
Compact Par 18 MKII Tour
Maintenance
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and
must not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
The Compact Par 18 MKII Tour requires almost no maintenance. However, you should keep the unit
clean.
Otherwise, the fixture’s light output will be significantly reduced. Disconnect the mains power supply, and
then wipe the cover with a damp cloth. Do not immerse in liquid. Wipe lens clean with glass cleaner and
a soft cloth. Do not use alcohol or solvents.
The front lens will require weekly cleaning, as smoke-fluid tends to build up residues, reducing the light-
output very quickly.
Please clean internal components once a year with a light brush and vacuum cleaner.
Keep connections clean. Disconnect electric power, and then wipe the DMX connections with a damp
cloth. Make sure connections are thoroughly dry before linking equipment or supplying electric power.
Troubleshooting
No Light
If the light effect does not operate properly, refer servicing to a technician.
Suspect three potential problem areas as: the power supply and the LEDs.
01) Power supply. Check that the unit is plugged into an appropriate power supply.
02) The LEDs. Return the Compact Par to your Showtec dealer.
03) If both appear to be O.K., plug the unit in again.
04) If you are unable to determine the cause of the problem, do not open the Compact Par, as this may
damage the unit and the warranty will become void.
05) Return the device to your Showtec dealer.
No Response to DMX
Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction.
01) Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is at fault. Does the controller operate properly with
other DMX products ? If not, take the controller in for repair. If so, take the DMX cable and the light
effect to a qualified technician.
Restore Factory Settings
You can discard all data by restoring the factory settings.
01) Press and hold down the MODE and SETUP buttons for 3 seconds.
02) The display will show and the settings will have been reset.

19
Ordercode: 42596
Compact Par 18 MKII Tour
Problem
Probable cause(s)
Solution
One or more
fixtures do not
function at all
No power to the fixture
•Check if power is switched on and
cables are plugged in
Fixtures reset
correctly, but all
respond
erratically or not
at all to the
controller
The controller is not connected.
•Connect controller.
3-pin XLR Out of the controller
does not match XLR Out of the first
fixture on the link (i.e. signal is
reversed)
•Install a phase reversing cable
between the controller and the
first fixture on the link
Fixtures reset
correctly, but
some respond
erratically or not
at all to the
controller
Poor data quality
•Check data quality. If much lower
than 100 percent, the problem
may be a bad data link
connection, poor quality or
broken cables, missing termination
plug, or a defective fixture
disturbing the link
Bad data link connection
•Inspect connections and cables.
Correct poor connections. Repair
or replace damaged cables
Data link not terminated with 120
Ohm termination plug
•Insert termination plug in output
jack of the last fixture on the link
Incorrect addressing of the fixtures
•Check address setting
One of the fixtures is defective and
disturbs data transmission on the
link
•Bypass one fixture at a time until
normal operation is restored:
unplug both connectors and
connect them directly together.
•Have the defective fixture
serviced by a qualified technician
3-pin XLR Out on the fixtures does
not match (pins 2 and 3 reversed)
•Install a phase-reversing cable
between the fixtures or swap pin 2
and 3 in the fixture that behaves
erratically
No light or lamp
cuts out
intermittently
Fixture is too hot
•Allow the fixture to cool down
•Make sure that air vents are not
blocked
•Turn up the air conditioning
LEDs damaged
•Disconnect the fixture and return it
to your dealer
The power supply settings do not
match local AC voltage and
frequency
•Disconnect fixture. Check settings
and correct if necessary