Shure UA845UWB User manual

UA845UWB
Antenna Distribution System
The Shure UA845UWB antenna distribution system user guide.
Version: 2 (2019-J)

Shure Incorporated
2/12
Table of Contents
UA845UWBAntenna Distribution System 3
General Description 3
System Features 3
System Components 3
Front and Rear Panels 4
Rack Mount Instructions 5
System Installation 5
Connecting Receivers 6
Single Antenna Distribution Setup 6
Multiple Antenna Distribution Setup 7
Selecting the Frequency Range 8
RF Power Overload 8
Optional Accessories 8
Selecting Antenna Cables 9
Enable or Disable DC Bias Voltage 9
Specifications 10
Certifications 11
Important Product Information 11
LICENSING INFORMATION 11

Shure Incorporated
3/12
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
UA845UWB
Antenna Distribution System
General Description
The Shure Model UA845UWB Antenna Distribution System allows up to four receivers to use the same set of antennas. There
are also power connectors for distributing power to each receiver. RF signal amplification compensates for insertion loss from
splitting the antenna input to multiple outputs. Cascade connectors allow connections to a fifth receiver or a second
UA845UWB. A button on the front panel switches between one of five frequency bands from 174 to 1805 MHz.
System Features
The Shure Model UA845UWB ensures maximum sensitivity and signal processing capability, providing the widest radio range
possible for the largest number of wireless receivers.
5 Selectable Frequency Ranges The UA845UWB allows more options for avoiding intermodulation artifacts by switching
between one of the five frequency bands.
RF Power LED Indicators Front panel LED indicators display red if RF power is overloading.
Expandability The UA845UWB Antenna Distribution System is designed for large wireless systems. Each unit allows up
to four wireless receivers to use the same two antennas, and the cascade ports allow connection to a fifth receiver or a
second UA845UWB.
Compatibility The UA845UWB is compatible with all Shure wireless microphone receivers operating within a compatible
frequency range.
Cascade Ports Two 50 ohm, BNC-antenna cascade ports allow an additional UA845UWB unit or a fifth wireless receiver.
A large wireless system can be run off of a single pair of antennas.
Power Output and Out Connectors Multiple receivers can be daisy-chained and powered from a single source via the
power output connectors.
Low Noise and Intermodulation Distortion The UA845UWB maintains clean signals with minimal distortion.
Insertion Loss Compensation Whenever a signal is split to multiple output ports, there is a loss in signal strength. The
UA845UWB amplifies signals to compensate, ensuring a strong signal to the receivers.
Front-Mounted Antennas The UA845UWB comes with hardware to front-mount the antennas, if desired.
System Components
UA845UWB Antenna/Power Distribution System
(4) Locking DC power cords (ULXD4)*
(4) Non-locking DC power cords (QLXD4, SLX4, BLX4R)
(10) 22 in. BNC cables**
(2) 6 ft. BNC cables
(2) Bulkhead adapters for front mounting antennas
(1) AC daisy-chain cord
(1) AC power cord
Rack-mounting hardware
*Not included with Model UA845UWB/LC variant
**Model UA845UWB/LC substitutes (2) 22 in. BNC cables.

Shure Incorporated
4/12
Front and Rear Panels
Front Panel
Rear Panel
①Mounts for front-mounted antenna
②RF Power Overload Indicators
Displays RF overload with 2 red LEDs for antenna A and B.
③Frequency Band Selector
④Power Switch
⑤AC Power Input Connector.
⑥AC Power Output Connector.
Each amplifier has a power output connector for daisy-chaining up to five Shure Diversity Single or Dual Receivers to a sin-
gle power source.
⑦Antenna In Ports, Channel A and B.
BNC connectors for antennas.
⑧RF Cascade Connectors Channel A and B.
BNC connectors for adding a fifth receiver, or an additional UA845UWB, permitting more wireless receivers to be connect-
ed.
⑨RF Output Connectors, Channel A and B.
BNC connectors for up to four wireless receivers.

Shure Incorporated
5/12
•
•
•
•
•
1.
2.
3.
⑩15 V DC Connectors
Four connectors for DC power.
Rack Mount Instructions
If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Keep the rack environment temperature at or below the maximum ambient temperature (Tma)
specified by the manufacturer of the installed equipment.
Provide the proper amount of air flow inside the rack as required for safe operation of the equipment.
Do not create a hazardous condition by mounting the equipment in the rack with an uneven mechanical load.
When connecting the equipment to the supply circuit, consider the effect that overloading of the circuits might have on
over-current protection and supply wiring. Consider all equipment nameplate ratings when addressing this concern.
Maintain reliable earthing of rack-mounted equipment. Give particular attention to indirect supply connections to the
branch circuit (e.g., power strips).
System Installation
Installing Front-Mounted Antennas
The UA845UWB comes equipped for front-mounted antennas. Front-mounting improves RF performance of the system by
moving the antennas to the front of the rack. When a unit is located in a rack, antennas should be either front- or remote-
mounted.
Insert the bulkhead adapters through the holes in each bracket, and secure them from each side, using the supplied
hardware.
Connect the supplied antenna cables to the receiver antenna inputs and adapters.
Install the antennas onto the bulkhead adapters protruding through the front panel.
Note: For the best results, point the antennas up and away from each other at 45° angles from vertical. This ensures the best possible reception and greatly
reduces the possibility of signal dropout. Always perform a walk-through test of the system in the performing area before using a wireless system.

Shure Incorporated
6/12
•
•
1.
2.
3.
Installing Remote Antennas
Remote-mounted antennas have the advantage of being free from the unit and closer to the transmitters. They can be placed
anywhere within the recommended cable length, creating a much wider radio reception range and further reducing the possibil-
ity of signal dropout. Please ask your Shure dealer for information on in-line RF amplifiers.
When remote mounting antennas, follow these guidelines:
When using long runs of cable, use Shure low-loss cables that are compatible with the operating frequency. If necessary,
use a Shure In-Line RF Amplifier.
Locate antennas more than 3 m (10 ft) from transmitters.
Connecting Receivers
Single Antenna Distribution Setup
Using Shure low-loss, 50 Ω coaxial cables, connect the right and left (channels 1 through 4, A and B) RF output ports
on the UA845UWB to the corresponding left and right antenna inputs on each receiver. Use the cascade ports to con-
nect a fifth receiver.
Using the supplied power cable, connect the UA845UWB to a power outlet.
To daisy-chain receivers together with power output cables, connect the power output connector of the UA845UWB to
the power input connector of one receiver. Connect the remaining receivers similarly. Connect the power input of the
unit to a power supply.
Note: No more than five Shure receivers should be powered through a daisy-chain from a single UA845UWB.

Shure Incorporated
7/12
1.
2.
3.
Single UA845UWB Setup
Multiple Antenna Distribution Setup
Connect the cascade ports for RF output channels A and B of one UA845UWB to the antenna input, channels A and B,
of a receiver or second UA845UWB.
If desired, connect additional units in the same manner.
To daisy-chain receivers with power output cables, connect the power output connector of the UA845UWB to the power
input connector of one receiver. Connect the remaining receivers similarly. Connect the power input of the unit to an AC
power source.
Warning: When adding additional UA845UWBs to a system, each UA845UWB should be connected to a separate power sup-
ply. No more than five receivers can be powered from a single UA845UWB. Daisy-chaining multiple UA845UWB's through the
power output ports will overload a single power supply, possibly causing damage to the equipment.

Shure Incorporated
8/12
1.
2.
3.
Multiple UA845UWB Setup
Selecting the Frequency Range
Press and hold the Set button until the green Frequency Band LED begins to flash.
Use the Set button to click through the five bands of frequency range options.
When the LED stops flashing, the illuminated range is selected.
RF Power Overload
When the Overload Antenna Indicator displays a red LED, it indicates that a strong RF signal is overloading the antenna ampli-
fier. To correct an overload condition, increase the distance between the antenna and transmitter, or lower the antenna gain
setting.
Warning: Overloading the antenna amplifier results in reduced channel count and poor system performance.
Optional Accessories
1/2 Wave Omnidirectional Receiver Antenna for improved wireless signal reception UA8
In-Line RF Amplifier compensates for signal loss over extended cable runs UA834

Shure Incorporated
9/12
1.
2.
3.
4.
UA874 Active Directional Antenna for improved wireless signal reception with
greater rejection of unwanted signals UA874
1/2 Wave Antenna Remote Mount Kit UA505
Antenna Rack Panel with Cables and BNC Adapters UA440
Note: Be sure to select antennas and accessories that are compatible with the operating frequency range of your wireless system. Contact Shure or your local
retailer for help with selecting the right wireless accessories.
Selecting Antenna Cables
Use 50 ohm low-loss coaxial cable, such as RG-8U. Shure offers pre-terminated antenna cables ranging from 6 to 100 feet.
NOTE: When ordering cables from Shure, select the low-loss "Z" models (available for longer cables) when using frequency bands above 1000 MHz.
Enable or Disable DC Bias Voltage
The DC bias voltage can be disabled on UA845UWB units built after August 10, 2018.
Note: The build date is printed on the bottom of the unit.
To disable the DC bias voltage:
Hold the SET button down and turn the unit on.
Release the SET button when all LEDs on the front panel turn on.
Power cycle the unit.
DC bias voltage is disabled when all green LEDs flash briefly and the one matching the selected frequency range re-
mains on.

Shure Incorporated
10/12
1.
2.
3.
4.
To enable the DC bias voltage:
Hold the SET button down and turn the unit on.
Release the SET button when the 2 red LEDs turn on.
Power cycle the unit.
DC bias voltage is enabled when the frequency range LED illuminates. (LEDs do not flash after power cycle when en
abling the DC bias voltage.)
Specifications
Carrier Frequency Range
Band 1 174 to 216 MHz
Band 2 470 to 960 MHz
Band 3 1240 to 1260 MHz
Band 4 1492 to 1525 MHz
Band 5 1785 to 1805 MHz
Distributed Output Level (Gain)
0dB, typical
Receiver Antenna Input, Output Ports1 to 4 -2 dB to +2 dB
Receiver Antenna Input, Cascade Output -1 dB to +1 dB
Output Connector Isolation
>25 dB, typical
Third-order Overload Intercept Point (OIP3)
24 dBm, typical
Input-Output AC Line Voltage, Switched
100 to 240 V AC, 50/60 Hz
DC Output
15 V DC, 4 Connectors
Output Current
Combined total from all DC outputs

Shure Incorporated
11/12
2.5 A, maximum
Impedance
50 Ω
Operating Temperature Range
-18°C (0°F) to 63°C (145°F)
Dimensions
44.5 x 482.6 x 295.3 mm H x W x D (1.75 x 19 x 11.6in.)
Net Weight
3.32 kg (7.3 lbs)
Connector Type
BNC
Power Consumption V AC
Typical without powered antenna attached or receivers connected to the DC outputs
14.1 W per unit
Certifications
The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact
information please visit www.shure.com
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: [phone]
Fax: [phone]
Email: [email protected]
This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking.
Important Product Information
LICENSING INFORMATION
Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for
possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to
operate the equipment. Licensing of Shure wireless microphone equipment is the user’s responsibility, and licensability de-

Shure Incorporated
12/12
pends on the user’s classification and application, and on the selected frequency. Shure strongly urges the user to contact the
appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies.
NOTE: ThisRadioequipmentisintendedforuseinmusicalprofessionalentertainmentandsimilarapplications.ThisRadioapparatusmaybecapableofoper
ating on some frequencies not authorized in your region. Please contact your national authority to obtain information on authorized frequencies and RF power
levels for wireless microphone products.