Shure SE215-BT1 User manual

1/12
SE215-BT1 -- Shure Bluetooth® Earphones
Wearing the Earphones
The following are some suggested ways of wearing the earphones.
Inserting the Earphones
Insert the earphones so they form a tight seal. The fit of the earphone can greatly affect sound quality.

Shure Incorporated
2/12
Important: If there seems to be a lack of low frequency response (bass), this means that the earphone sleeve is
not forming a tight seal. Gently push the earphone deeper into the ear canal or try a different sleeve.
Warning: Do not push the earphone sleeve beyond the ear canal opening.
Removing the Earphones
Grasp the body of earphone and gently twist to remove.
Note: Do not pull on cable to remove earphone.
Changing Sleeves
•Twist and pull to remove the sleeve from the nozzle.
•Slide on a new sleeve so that it completely covers the barb and the nozzle.

Shure Incorporated
3/12
Caution: If the barb or any of the nozzle is exposed, the sleeve is not properly installed. Replace sleeves if they
do not tightly grip the nozzle. To ensure proper fit and performance, use only sleeves supplied by Shure (unless
using custom molded sleeves).
Choosing a Sleeve
Soft flex sleeves are included in small, medium, and large sizes. Select an earphone sleeve that provides the best
fit and sound isolation. It should be easy to insert, fit comfortably, and easy to remove.
Soft Flex Sleeves
Cleaning the Nozzle
If you notice a change in sound quality, remove the sleeve and check the nozzle of your earphone. If nozzle is
blocked, clear obstruction by using wire loop end of cleaning tool.

Shure Incorporated
4/12
Warning: The cleaning tool is only to be used to clean the earphones. Any other use, such as using the tool to
clean ears, could result in injury.
Maintenance and Cleaning
Careful maintenance ensures a tight seal between the sleeve and nozzle, improving sound quality and product
safety.
•Keep the earphones and sleeves as clean and dry as possible.
•To clean sleeves, remove them from earphones, gently rinse in warm water and air dry. Foam sleeves require a
longer drying time. Inspect for damage and replace if necessary. Ear sleeves must be completely dry before
reusing.
• Wipe the earphones and sleeves with mild antiseptic to avoid infections. Do not use alcohol-based disinfec-
tants.
•Do not expose earphones to extreme temperatures.
•Replace sleeves if they do not fit properly.

Shure Incorporated
5/12
•Do not attempt to modify this product. Doing so will void the warranty and could result in personal injury and/or
product failure.
Bluetooth Pairing
1. Turn off the earphones. Press and hold center button on earphone remote until the LED flashes blue and red.
2. From your audio source, select "Shure BT1."
3. LED turns blue when successfully paired.
For additional pairing options, please visit http://www.shure.com/earphones (http://www.shure.com/earphones).
Charging the Earphones
Red LED indicates low battery.
1. Connect earphones to charging device using supplied cable.
2. LED is red while charging.
3. When earphones are charged, LED turns off.
Warning: Before charging, make sure the product is at room temperature, between 0 to 45°C (32 to 113°F).
Note: Use this product only with an agency approved power supply which meets local regulatory requirements
(e.g., UL, CSA, VDE, CCC, INMETRO).
Using the Remote
The Center Button

Shure Incorporated
6/12
Power on Press and hold
Power off Press and hold, 5 seconds
Bluetooth pair Press and hold, 10 seconds
Play/Pause Click once
Answer/End a call Click once
Decline a call Press and hold, 3 seconds
Activate voice assistant Phone on, press and hold, 3 seconds
Up and Down Buttons
Volume Up/Down Click + or -
Next track Press and hold +, 3 seconds
Previous track Press and hold -, 3 seconds
Your phone may not be compatible with some functions. Visit http://www.shure.com/earphones (http://
www.shure.com/earphones) for more information.
Specifications
Transducer Type
Single High-Definition MicroDriver
Sensitivity
at 1 kHz
107 dB SPL/mW
Impedance
at 1 kHz
17 Ω

Shure Incorporated
7/12
Frequency Range
SE215 Special Edition 21 Hz –17.5 kHz
SE215 22 Hz –17.5 kHz
Net Weight
30 g (1 oz.)
Bluetooth Specifications
Antenna Type
Chip
Antenna Gain
+2.13 dBi
Bluetooth 4.1
Frequency
2402 to 2480 MHz
Modulation Type
FHSS
RF Output Power
+5.38 dBm (E.I.R.P)
Accessories
For information about earphone accessories and other Shure products visit:
http://www.shure.com/americas/products/accessories/earphones (http://www.shure.com/americas/products/acces-
sories/earphones)
Furnished accessories subject to change.
Safety Information
Visit http://www.shure.com/earphones (http://www.shure.com/earphones) for the latest regulatory and compliance
information.
WARNING
•Follow instructions from manufacturer.
• Product battery may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disas-
semble, heat above 140°F (60°C), or incinerate.

Shure Incorporated
8/12
•Attention should be drawn to the environmental aspects of battery disposal.
•Product shall not be exposed to excessive heat such as sunshine, fire, or the like.
•Do NOT make unauthorized alterations to this product.
WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or
other reproductive harm.
Note: Battery replacement to be performed only by Shure authorized service personnel.
CAUTION: Follow applicable laws regarding mobile phone and headphone use while driving.
This product contains magnetic material. Consult your physician on whether this might affect your implantable
medical device.
Information to the user
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harm-
ful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC Part 15.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's au-
thority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est con-
forme à la norme NMB-003 du Canada.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation of this device is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must accept any inter-
ference, including interference that may cause undesired operation of the device. Le présent appareil est con-
forme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est au-
torisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromet-
tre le fonctionnement.
Note: Testing is based on the use of supplied and recommended cable types. The use of other than shielded
(screened) cable types may degrade EMC performance.
Este equipo ha sido diseñado para operar con las antenas que enseguida se enlistan y para una ganancia máxi-
ma de antena de [+2.13] dBi. El uso con este equipo de antenas no incluidas en esta lista o que tengan una
ganancia mayor que [+2.13] dBi quedan prohibidas. La impedancia requerida de la antena es de [50] ohms.

Shure Incorporated
9/12
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispos-
itivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, in-
cluyendo la que pueda causar su operación no deseada.
1. 經審驗合格之射頻電信終端設備，非經許可，公司、商號或使用者均不
得擅自變更頻率、加大功率或變更原設計之特性及功能。
2. 射頻電信終端設備之使用不得影響飛航安全及干擾合法通信；經發現有
干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。所謂合法
通信，係指依電信法規定作業之無線電信。
3. 輸入、製造射頻電信終端設備之公司、商號或其使用者違反本辦法規
定，擅自使用或變更無線電頻率、電功率者，除依電信法規定處罰外，
國家通訊傳播委員會並得撤銷其審驗合格證明。
4. 減少電磁波影響，請妥適使用
根據NCC低功率電波輻射性電機管理辦法 規定:
1. 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或
使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
2. 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經
發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前
項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍
受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
運用に際しての注意
この機器の使用周波数帯では、電子レンジ等の産業・科学・医療用機器のほか
工場の製造ライン等で使用されている移動体識別用の構内無線局（免許を要
する無線局）及び特定小電力無線局（免許を要しない無線局）並びにアマ
チュア無線局（免許を要する無線局）が運用されています。
1. この機器を使用する前に、近くで移動体識別用の構内無線局及び特定小
電力無線局並びにアマ チュア無線局が運用されていないことを確認し
て下さい。
2. 万一、この機器から移動体識別用の構内無線局に対して有害な電波干渉
の事例が発生した場合には、 速やかに使用周波数を変更するか又は電波
の発射を停止した上、下記連絡先にご連絡頂き、混 信回避のための処
置等（例えば、パーティションの設置など）についてご相談して下さい。

Shure Incorporated
10/12
3. その他、この機器から移動体識別用の特定小電力無線局あるいはアマ
チュア無線局に対して有害な電波干渉の事例が発生した場合など何かお
困りのことが起きたときは、保証書に記載の販売代 理店または購入店
へお問い合わせください。代理店および販売店情報はShure 日本語ウェ
ブサイト http://www.shure.co.jp (http://www.shure.co.jp) でもご覧いた
だけます。
現品表示記号について
現品表示記号は、以下のことを表しています。 この無線機器は2.4GHz 帯
の電波を使用し、変調方式は「FH-SS」方式、想定与干渉距離は10m です。
2,400MHz～2,483.5MHz の全帯域を使用し、移動体識別装置の帯域を回避
することはできません。
Japanese Radio Law and Japanese Telecommunications Business Law
Compliance. This device is granted pursuant to the Japanese Radio Law
(電波法) and the Japanese Telecommunications Business Law (電気通信
事業法). This device should not be modified (otherwise the granted desig-
nation number will become invalid).
Este equipamento opera em caráter secundário, isto é, não tem direito a
proteção contra interferência prejudicial, mesmo de estações do mesmo
tipo, e não pode causar interferência a sistemas operando em carater pri-
mario.
Este produto está homologado pela ANATEL, de acordo com os procedi-
mentos regulamentados pela Resolução 242/2000, e atende aos requisitos
técnicos aplicados. Para maiores informações, consulte o site da ANATEL
- http://www.anatel.gov.br (http://www.anatel.gov.br)

Shure Incorporated
11/12
TRA REGISTERED No: ER56780/17
DEALER No: 67442/17
The Bluetooth word mark and logos are registered trademarks owned by
the Bluetooth SIG, Inc. and any use of such marks by Shure Incorporated
is under license. Other trademarks and trade names are those of their re-
spective owners.
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual
waste, but have to be disposed of separately. The disposal at the commu-
nal collecting point via private persons is for free. The owner of old appli-
ances is responsible to bring the appliances to these collecting points or to
similar collection points. With this little personal effort, you contribute to re-
cycle valuable raw materials and the treatment of toxic substances.
Paraguay Distributor: Microsystems S.R.L., Senador Long 664 c/Dr. Lilio,
Asunción, Paraguay
Certifications
This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking.
Hereby, Shure Incorporated declares that the radio equipment is in compliance with Directive 2014/53/EU. The full
text of the EU declaration of conformity is available at the following internet address: http://www.shure.com/europe/
compliance (http://www.shure.com/europe/compliance)
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa

Shure Incorporated
12/12
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: [phone]
Fax: [phone]
Email: [email protected]