Shuttle XPC Barebone SH67H3 User manual

SH67H3 Quick Guide【 English 】
B1. AC Power Socket
B2. DVI-I Port
B3. HDMI Port
B4. USB3.0 Ports
B5. Esata & USB2.0 Ports
B6. LAN & USB2.0 Ports
B7. Line-In Port
B8. Center/Bass Port
B9. Front Out (L/R)
B10. Side Surr (L/R)
B11. Clear CMOS Button
B12. Surround Back
(L/R) Port
B13. SPDIF Out Port
B14.
Wireless LAN
Perforation
B15. Serial Port Perforation
F1. 5.25” Bay
F2. 3.5” Bay
F3. Power Switch
& Power LED
F4. HDD LED
F5. Reset
F6. Headphone
F7. Mic In
F8. USB3.0 Ports
F9. eSATA+USB2.0
Port
Back Panel
F5
F1
B10
B9
B12
B7
B14
B3
B1 B6B5
B4
B8
B15 B14
F3
F2
F4
B2
12. Fasten the Smart Fan
to the chassis with the
4 thumbscrews.
A. Begin Installation
1. Unscrew 3 thumbscrews of the chassis cover.
2. Slide the cover backwards and upwards.
3. Unfasten the rack mount screws and remove the rack.
B. CPU and ICE Installation
For safety reasons, please ensure that the power cord is
disconnected before opening the case.
1. Unfasten the ICE fan thumbscrews on the back of the chassis.
2. Unfasten the four ICE module attachment screws and unplug the fan
connector.
3. Remove the ICE module from the chassis and put it aside.
1. Unlock the DIMM latch.
2. Align the memory module's cutout with the DIMM slot notch.
Slide the memory module into the DIMM slot.
C. Memory module Installation
3. Check that the latches are closed, and the memory module is firmly installed.
D. Peripheral Installation
1. Unfasten expansion slot bracket screws.
Remove the back panel bracket and put the bracket aside.
E. Accessories Installation
2. Install the PCI/PCI Express x16 card into the PCI/PCI Express x16 slots.
3. Secure the bracket.
F. Complete
Please press "Del" key while booting to enter BIOS and load the
optimised BIOS settings.
Fan Connector
The maximum size acceptable for display cards is
267mm x 98mm x 34.6mm.
1. Replace the cover and refasten the thumbscrews.
2. Complete.
This 1155 pin socket is fragile and easily damaged. Always use
extreme care when installing a CPU and limit the number of times
that you remove or change the CPU. Before installing the CPU,
make sure to turn off the computer and unplug the power cord
from the power outlet to prevent damage to the CPU.
VGA Card PCB
Chassis
Cover
5mm 34.6mm
5. Connect the Serial ATA and power cables to the optical drive.
Make sure that the motherboard supports the memory.
It is recommended that memory of the same capacity, brand,
speed,and chips are used.
(Go to Shuttle's website for the latest memory support list.)
Memory modules have a foolproof design. A memory module can
be installed in only one direction. If you are unable to insert the
memory, switch the direction.
Guidelines for Memory Con󰘰guration
Before installing DIMMs, read and follow these guidelines for memory
configuration.
Installing a memory module
DDR3 DIMMs are not compatible to each other or DDR DIMMs.
Be sure to install DDR3 DIMMs on this motherboard. Follow the steps below
to correctly install your memory modules in the memory sockets.
Repeat the above steps to install additional memory modules,
if required.
Cutout
Latch Latch
Notch
DDR3 240-pin 1.5V
48*2=96 pin 72*2=144 pin
A DDR3 memory module has a cutout, so it can only fit in one direction.
10. Screw the ICE module to the mainboard. Note to press down on the
opposite diagonal corner while tightening each screw.
11. Connect the fan connector.
4. First unlock. Press Awith your thumb, then move it to Buntil it is
released from the retention tab and raise the socket lever.
Follow the steps below to correctly install the CPU into the
motherboard CPU socket.
Please be aware of the CPU orientation, DO NOT force the CPU into the
socket to avoid bending of pins on the socket and damage of CPU!
6. Orientate the CPU and socket, you may align the CPU notches with the
socket alignment keys. Make sure the CPU is perfectly horizontal, insert
the CPU into the socket.
DO NOT touch socket contacts. To protect the CPU socket, always
replace the protective socket cover when the CPU is not installed.
Socket 1155
CPU
Triangle Pin1
Marking
on the CPU
Notch on the CPU/ Alignment Key of the CPU Socket
2
1
3
LThe product’s colour and specification will depend on the actual shipping product.
Fan Connector
1
2
3
4
4. Connect the Serial ATA and power cables to the HDD.
2. Place the HDD and optical drive in the rack and secure with screws
from the side.
3. Place the rack in the chassis and refasten the rack.
1. Loosen the purse lock and separate the Serial ATA and power cables.
Please do not apply excess amount of thermal paste.
7. Close the metal load plate, lower the CPU socket lever and lock in place.
8. Spread thermal paste evenly on the CPU surface.
Retention tab
A
B
5. Lift the metal load plate on the CPU socket.
1
2
Metal load plate
Notch on the CPU/ Alignment Key of the CPU Socket
Dual-Channel mode Population Rule
In Dual-Channel mode, the memory modules can transmit and receive
data with two data bus lines simultaneously. Enabling Dual-Channel
mode can enhance the system performance. The following illustrations
explain the population rules for Dual-Channel mode.
DIMM1 (Red),Installed
DIMM2 (Yellow),Installed
DIMM3 (Red),Installed
DIMM4 (Yellow),Installed
A
B
Metal load plate
Thermal Paste
application area
Load lever
PCI Express x16 slot
PCI-e slot
Serial ATA Cable
Serial ATA Power Cable
Serial ATA Cable
Serial ATA Power Cable
Serial ATA HDD
Serial ATA Optical Drive
PCI Express x16 slots / PCI
Jumper Settings
Safety Information
Read the following precautions before setting up a Shuttle XPC.
Laser compliance statement
The optical disc drive in this PC is a laser product.
The drive's classi󰘰cation label is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION：INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
CAUTION
Incorrectly replacing the battery may damage this computer.
Replace only with the same or equivalent as recommended by Shuttle.
Disposal of used batteries according to the manufacturer's instructions.
B13
B11
F6 F7 F9
F8
Motherboard Illustration
4x 240 pins DDR3
DIMM Slots
FAN Connector-
CPU_FAN1 USB Headers-
USB1
Center/Bass/
Surround-Back/
Side Surround Ports
Front-Out/Line-In Ports
2x USB 2.0 Ports
& Esata Port
ATX Power
Connector-ATX2
ATX Power
Connector-PWR1
Serial ATA-SATA 3,4
Clear CMOS Button
Fornt panel
connector -JP7
S/PDIF-Out-JP1
AUX IN Connector
-AUX_IN1
J6
J3
Intel H67 Chipset
Front Connector-JP3
Socket 1155
J2 J5
J1
FAN Connector-
FAN1
J2
HDMI Port &
DVI-I Port
One PCI Express x1
Slot
One PCI Express x16
Slot
SATA 6.0Gbs-SATA 1,2
2x USB 3.0 Ports
2x USB 2.0 Ports
& 1x LAN1
CIR Connector-JP6
USB3.0 Connector CN5
RS232 Header-
COM1
J4
J8
Front Panel
9. Tear off the protective membrane from the bottom of ICE module.
Remove the protective socket mylar from the CPU socket.
DVI-I & HDMI Ports cannot be used, if the
PCI-e/ PCI Express graphics card is installed.
Remove the
protective
membrane
Pin Assignments (JP1):
1=GND
2=VCC
3=SPDIFO
J2 
Fan Connectors
J3 
AUX IN Connector
Pin Assignments (AUX_IN1):
1=CD_IN_L
2=Ground
3=Ground
4=CD_IN_R
4 3 2 1
J5 
USB Connector
FAN_SENSE
FAN_PWM +12V Ground
CPU_FAN1 FAN1
Ground
FAN_SENSE
+12V
1 2 3
Pin Assignments (USB1):
1=VCC 2=VCC
3=D1- 4=D0-
5=D1+ 6=D0+
7=Ground 8=Ground
9=KEY 10=Ground
9 7 5 3 1
10 8 6 4 2
J1 S/PDIF Out connector
J6 
Front Connector
Pin Assignments (JP3):
1=HDD_IED 2=Power_LED
3=HDD_IED- 4=Ground
5=Reset_button 6=Power_button
7=Ground 8=Ground
9=NC 10=NA
9 7 5 3 1
10 8 6 4 2
Pin Assignments (JP6):
1=Ground
2=5V_DUAL
3=CIR-RX
1 2 3
J4 CIR connector
J8 
RS232 Header
Pin Assignments (COM1):
1=DCD1P 2=RX1P
3=TXD1P 4=DTR1P
5=Ground 6=DSR1P
7=RTS1P 8=CTS1P
9=-XRI 10=NA
9 7 5 3 1
10 8 6 4 2
J7 
USB 3.0 Connector
Pin Assignments (CN5):
1=Wake- 2=-PCI-E RST 3=Ground 4=USB3_100M+
5=USB3_100M- 6=Ground 7=PET2P 8=PET2N
9=-Ground 10=PER2P 11=PER2N
12=Ground 13=VCC3 14=VCC3
53R-SH67H3-2001
J7
DIMM1 (Red),Empty
DIMM2 (Yellow),Installed
DIMM3 (Red),Empty
DIMM4 (Yellow),Installed