Shuttle SH61R4 User manual

SH61R4 Quick Guide【 English 】
B1. AC Power Socket
B2. Kensington Lock
B3. Serial Port
Perforation
(Optional)
B4. SPDIF Out Port
(Optional)
B5. DVI-I Port
B6. DVI-D Port
B7. USB3.0 Ports
B8. Microphone Jack
B9. Line-Out Jack
B10. Line-In Jack
B11. LAN & USB2.0 Ports
B12. Clear CMOS Button
B13. USB2.0 Ports
B14.
Wireless LAN
Perforation
Back Panel
B8
B6
B1
B7
B10
B14
B5
12. Fasten the Smart Fan
to the chassis with the
4 thumbscrews.
A. Begin Installation
1. Unscrew 3 thumbscrews of the chassis cover.
2. Slide the cover backwards and upwards.
3. Unfasten the rack mount screws and remove the rack.
B. CPU and ICE Installation
For safety reasons, please ensure that the power cord is
disconnected before opening the case.
1. Unfasten the ICE fan thumbscrews on the back of the chassis.
2. Unfasten the four ICE module attachment screws and unplug the fan
connector.
3. Remove the ICE module from the chassis and put it aside.
1. Unlock the DIMM latch.
2. Align the memory module's cutout with the DIMM slot notch.
Slide the memory module into the DIMM slot.
C. Memory module Installation
3. Check that the latches are closed, and the memory module is firmly installed.
1. Unfasten expansion slot bracket screws.
Remove the back panel bracket and put the bracket aside.
E. Accessories Installation
2. Install the PCI Express x16 card into the PCI Express x16 slots.
3. Secure the bracket.
F. Complete
Please press "Del" key while booting to enter BIOS and load the
optimised BIOS settings.
Fan Connector
The maximum size acceptable for display cards is
267mm x 98mm x 34.6mm.
1. Replace the cover and refasten the thumbscrews.
2. Complete.
This 1155 pin socket is fragile and easily damaged. Always use
extreme care when installing a CPU and limit the number of times
that you remove or change the CPU. Before installing the CPU,
make sure to turn off the computer and unplug the power cord
from the power outlet to prevent damage to the CPU.
VGA Card PCB
Chassis
Cover
5mm 34.6mm
5. Connect the Serial ATA and power cables to the optical drive.
Installing a memory module
DDR3 DIMMs are not compatible with DDR/DD2 or DDR DIMMs.
Be sure to install DDR3 DIMMs on this motherboard. Follow the steps below
to correctly install your memory modules in the memory sockets.
Repeat the above steps to install additional memory modules,
if required.
Cutout
Latch Latch
Notch
DDR3 240-pin 1.5V
48*2=96 pin 72*2=144 pin
A DDR3 memory module has a cutout, so it can only fit in one direction.
10. Screw the ICE module to the mainboard. Note to press down on the
opposite diagonal corner while tightening each screw.
11. Connect the fan connector.
4. First unlock. Press Awith your thumb, then move it to Buntil it is
released from the retention tab and raise the socket lever.
Follow the steps below to correctly install the CPU into the
motherboard CPU socket.
Please be aware of the CPU orientation, DO NOT force the CPU into the
socket to avoid bending of pins on the socket and damage of CPU!
6. Orientate the CPU and socket, you may align the CPU notches with the
socket alignment keys. Make sure the CPU is perfectly horizontal, insert
the CPU into the socket.
DO NOT touch socket contacts. To protect the CPU socket, always
replace the protective socket cover when the CPU is not installed.
Socket 1155
CPU
Triangle Pin1
Marking
on the CPU
Notch on the CPU/ Alignment Key of the CPU Socket
2
1
3
LThe product’s colour and specification will depend on the actual shipping product.
Fan Connector
1
2
3
4
4. Connect the Serial ATA and power cables to the HDD.
3. Place the rack in the chassis and refasten the rack.
Please do not apply excess amount of thermal paste.
7. Close the metal load plate, lower the CPU socket lever and lock in place.
8. Spread thermal paste evenly on the CPU surface.
Retention tab
A
B
5. Lift the metal load plate on the CPU socket.
1
2
Metal load plate
Notch on the CPU/ Alignment Key of the CPU Socket
Metal load plate
Thermal Paste
application area
Load lever
PCI Express x16 slot
PCI Express
Serial ATA Cable
Serial ATA Power Cable
Serial ATA Cable
Serial ATA Power Cable
2. Place the HDD and optical drive in the rack and secure with screws
from the side.
1. Loosen the purse lock and separate the Serial ATA and power cables.
Serial ATA HDD
Serial ATA Optical Drive
PCI Express x16 slots / PCI
Pin Assignments
Safety Information
Read the following precautions before setting up a Shuttle XPC.
Laser compliance statement
The optical disc drive in this PC is a laser product.
The drive's classi󰘰cation label is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION：INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
CAUTION
Incorrectly replacing the battery may damage this computer.
Replace only with the same or equivalent as recommended by Shuttle.
Disposal of used batteries according to the manufacturer's instructions.
Motherboard Illustration
2x 240 pins DDR3 DIMM Slots
USB Header-USB2
Line-Out/Line-In Ports/
MIC Port
2x USB 2.0 Ports & 1x LAN
ATX Power
Connector-ATX1
ATX Power
Connector-PWR1
Serial ATA-SATA 1,2,3,4
CIR connector -JP6
AUX IN Connector-
AUX_IN1
Intel H61 Chipset
Socket 1155
J4
J1
CPU_FAN Connector-
FAN2
J2
DVI-D Port & DVI-I Port
One PCI Express x1 Slot
One PCI Express x16 Slot
LPC Header-JP1
S/PDIF output Connector
-SPDIF1
2x USB 2.0 Ports
COM Header-COM1
J8
Front Panel
9. Tear off the protective membrane from the bottom of ICE module.
Remove the protective socket mylar from the CPU socket.
DVI-I & DVI-D Ports cannot be used, if the
PCI Express graphics card is installed.
Remove the
protective
membrane
J2 
AUX IN Connector - (AUX_IN1)
1=AUX_IN_L
2=Ground
3=Ground
4=AUX_IN_R
4 3 2 1
J4 
Fan Connectors
SPEED_SENSE
PWM_CTRL +12V Ground
J1 
USB Header - (USB2)
1=5V_USB 2=5V_USB
3=USB A- 4=USB B-
5=USB A+ 6=USB B+
7=GND 8=GND
9=NULL 10=NA
2 4 6 8 10
1 3 5 7 9
1=Ground
2=VCC
3=SPDIF_O
1 2 3
J3 
S/PDIF Out connector - (SPDIF1)
J5 
Power Header - (JP3)
1=+HD_LED 2=PWR_LED
3=-HD_LED 4=GND
5=RST_SW 6=PWR_SW
7=GND 8=GND
9=NA 10=NULL
9 7 5 3 1
10 8 6 4 2
1=Ground
2=5V_DUAL
3=CIR-RX
1 2 3
J7 CIR connector - (JP6)
J8 COM Header - (COM1)
9 7 5 3 1
10 8 6 4 2
53R-SH61R3-2001
F1. HDD LED
F2. Power Button / Power LED
F3. 5.25” Bay
F4. USB2.0 Ports
F5. Microphone
F6. Headphone
F1
F4
F3
F4F5 F6
F2
B9
B11
B14
B2
B3
B14
B12
B13
B4
Clear CMOS Button
2x USB 2.0 Ports
2x USB 3.0 Ports
FRONT audio Header
-JP5
FAN Connector-FAN1
Power Header-JP3
J3
J4
J5
J6
J7
SPEED_SENSE
PWM_CTRL +12V Ground
J6 
Front audio Header - (JP5)
1=Front MIC_L 2=AGND
3=Front MIC_R 4=Front Audio detect
5=Head phone_R 6=Front MIC SENSE_Return
7=Front SENSE 8=NULL
9=Head phone_L 10=Head phone SENSE_Return
1
3
5
7
9
2
4
6
8
10
D. Peripheral Installation
J9
FAN1 CPU_FAN2
1=DCD1 2=RX1
3=TXD1 4=DTR1
5=Ground 6=DSR1
7=RTS1 8=CTS1
9=-XRI 10=NULL
LPC Header - (JP1)
11 12 13 14 15 16 17 18 19
1 2 3 4 5 6 7 8 9 10
1=+12V 11=-12V
2=5V 12=3VSB
3=5VSB 13=RI
4=SERIRQ 14=LDRQ
5=CLK-48M 15=PME
6=CLK-33M 16=LAD1
7=SIORST# 17=LAD0
8=LFRAME 18=+3.3V
9=LAD3 19=GND
10=LAD2
J9
62R-SH61R0-0601
English.Spanish.Korean.
Traditional Chinese.Japanese.
French. German Quick Guide