Siemens MXL-IQ Instruction Manual

MXL-IQ CONTROL PANEL
Operation, Installation, and Maintenance Manual
P/N 315-093624-13
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Building Technologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada

CAUTION
ALL WIRING MUST BE DONE AS DESCRIBED BELOW
TO OBTAIN SAFE AND PROPER SYSTEM OPERATION.
1. Earth ground the MXL-IQ enclosure properly; see the latest edition of the National
Electrical Code for approved methods. Conduit ground is NOT adequate.
2. Separate all wiring for initiating devices (i.e., detectors, manual stations, TRI
modules, etc.) from all other wiring in the MXL-IQ enclosure. To wire the Sys-
tem in compliance with UL 864, refer to the Installation and Power Limited
Wiring Instructions for the MSE-3L Enclosure, P/N 315-095445.
3. INSULATE ALL CABLE DRAIN WIRES from any conduit or earth grounded
electrical box, including those in the MXL-IQ enclosure.
4. Connect shield cable drain wire ONLY inside the MXL-IQ enclosure.
5. No wiring used for any of the following can run outside the building:
• an ALD loop
• a RS-485 network
• an NAC circuit used for audibles
• a CZM-1B6 or CZM-4 initiating device loop
For additional wiring information, refer to this manual or call Siemens
Industry, Inc., Technical Support Department at 1-800-248-7976.

i
Chapter 1
Table Of Contents
Description ______________________________ 1 - 1
Introduction ____________________________________________________ 1 - 1
Software ______________________________________________________ 1 - 1
MinimumMXL-IQControlPanelConfiguration ________________________ 1 - 3
Components OfThe Basic System __________________________________ 1 - 4
SMB-2MainBoard _____________________________________________ 1 - 4
MPS-6 Power Supply ___________________________________________ 1 - 5
MPS-12 Power Supply __________________________________________ 1 - 5
MKBKeyboard/AnnunciatorPanel _________________________________ 1 - 5
PIM-1PeripheralInterfaceModule__________________________________ 1 - 6
PIM-2PeripheralInterfaceModule__________________________________ 1 - 6
PAL-1________________________________________________________ 1 - 6
MSE-3LorMSE-3MEnclosure ____________________________________ 1 - 7
TSW-2 Tamper Switch __________________________________________ 1 - 7
BP-61 Batteries________________________________________________ 1 - 7
BTX Batteries _________________________________________________ 1 - 7
Optional Modules _______________________________________________ 1 - 8
ALD-2IAnalogLoopDriver _______________________________________ 1 - 8
CCU/MPagerInterfaceModule ____________________________________ 1 - 8
CMI-300InterfaceModule ________________________________________ 1 - 8
CPY-HLIInterfaceCard* _________________________________________ 1 - 8
CRM-4RelayModule ___________________________________________ 1 - 9
CSM-4SignalModule ___________________________________________ 1 - 9
CZM-4ConventionalZoneModule__________________________________ 1 - 9
D2300CP Fiber Optic Interface ___________________________________ 1 - 10
LLM-1LeasedLineModule ______________________________________ 1 - 10
MDACTSerialDialer ___________________________________________ 1 - 10
MID-16InputDriver* ___________________________________________ 1 - 10
MOD-16 Output Driver*_________________________________________ 1 - 11
MOI-7VoiceandAnnunciatorDriver* ______________________________ 1 - 11

Table of Contents
ii
MOM-2 Card Cage ____________________________________________ 1 - 11
MOM-4 Card Cage ____________________________________________ 1 - 12
NIM-1WNetworkInterfaceModule ________________________________ 1 - 12
PS-5A Power Supply* __________________________________________ 1 - 13
RCC Remote Command Center__________________________________ 1 - 13
RDM-PC Remote Diagnostics Module _____________________________ 1 - 13
Silent Knight Model 5128/5129 Digital Fire Communicator ______________ 1 - 14
Intelligent/Analog Devices _______________________________________ 1 - 14
FP-11Intelligent/AnalogPhotoelectricDetector ______________________ 1 - 14
FPT-11 Intelligent Thermal Detector _______________________________ 1 - 14
ICPIntelligentControlPoint______________________________________ 1 - 14
ICP-B6IntelligentControlPoint ___________________________________ 1 - 14
ID-60PIntelligent/AnalogPhotoelectricDetector ______________________ 1 - 14
ID-60PT Intelligent/Analog Photo-electric Detector with Heat Sensor ______ 1 - 14
ID-60IIntelligent/AnalogIonizationDetector__________________________ 1 - 15
ID-60IHIntelligent/AnalogIonizationHighAltitudeDetector ______________ 1 - 15
ID-60IAIntelligent/AnalogIonization HighAir-VelocityDetector ___________ 1 - 15
ID-60IAHIntelligent/AnalogIonizationHighAir-Velocity,HighAltitudeDetector 1 - 15
ID-60IBIntelligent/AnalogIonizationAir-Duct Detector _________________ 1 - 15
ID-60IBHIntelligent/AnalogIonizationAir-Duct HighAltitude Detector ______ 1 - 15
ILI-1Intelligent/AnalogIonizationDetector ___________________________ 1 - 15
ILI-1HIntelligent/AnalogIonizationHighAltitudeDetector _______________ 1 - 15
ILI-1AIntelligent/AnalogIonization HighAir-VelocityDetector _____________ 1 - 15
ILI-1AHIntelligent/AnalogIonizationHighAir-Velocity,HighAltitudeDetector _ 1 - 15
ILI-1BIntelligent/AnalogIonizationAir-Duct Detector ___________________ 1 - 16
ILI-1BHIntelligent/AnalogIonizationAir-DuctHighAltitudeDetector _______ 1 - 16
ILP-1Intelligent/AnalogPhotoelectricDetector _______________________ 1 - 16
ILPT-1 Intelligent/Analog Photoelectric Detector with Heat Sensor ________ 1 - 16
ILP-2Intelligent/AnalogPhotoelectricDetector _______________________ 1 - 16
ILT-1IntelligentThermal Detector _________________________________ 1 - 16
LIM-1LoopIsolatorModule ______________________________________ 1 - 16

Table of Contents
iii
Chapter 2
MSI-10/20IntelligentManual Station _______________________________ 1 - 16
MSI-10B/20BIntelligentManualStation _____________________________ 1 - 16
MSI-B6FIntelligentManualStation_________________________________ 1 - 16
MSI-MB6IntelligentManual Station ________________________________ 1 - 16
MS-MIIntelligentManual Station __________________________________ 1 - 16
TRI-B6,TRI-B6R,andTRI-B6D Intelligent Interface Modules ____________ 1 - 17
CZM-1B6RemoteConventionalZoneModule________________________ 1 - 17
DI-3 Ionization Detector_________________________________________ 1 - 17
DI-3HIonizationHighAltitude Detector _____________________________ 1 - 17
TRI-B6MAddressableInterfaceModule ____________________________ 1 - 17
TRI-S,TRI-R,andTRI-DIntelligent Interface Modules _________________ 1 - 17
CONVENTIONAL DEVICES _______________________________________ 1 - 17
DI-A3IonizationHighAir-Velocity Detector __________________________ 1 - 17
DI-A3HIonizationHighAir-Velocity,HighAltitudeDetector_______________ 1 - 17
DI-B3 IonizationAir Duct Detector_________________________________ 1 - 17
DI-B3HIonizationAirDuctHighAltitudeDetector _____________________ 1 - 18
DT-11 Thermal Detector ________________________________________ 1 - 18
PE-3 Photoelectric Detector _____________________________________ 1 - 18
PE-3T Photoelectric Detector with Heat Sensor ______________________ 1 - 18
PE-11 Photoelectric Detector ____________________________________ 1 - 18
PE-11T Photoelectric Detector with Heat Sensor _____________________ 1 - 18
PBA-1191 Linear Beam Smoke Detector ___________________________ 1 - 18
Installation ______________________________ 2 - 1
GeneralGuidelinesForInstallingTheMXL-IQ_________________________ 2 - 1
Installation Instructions ForThe MXL-IQ Control Panel ___________________ 2 - 2
Start Up Procedure ____________________________________________ 2 - 10
System Function Checkout______________________________________ 2 - 16

Table of Contents
iv
Chapter 3 Operation _______________________________ 3 - 1
Introduction ____________________________________________________ 3 - 1
System Modules _______________________________________________ 3 - 2
Remote System Modules ________________________________________ 3 - 2
UsingThe MKB-4 Keyboard/Annunciator Panel in Local Mode ____________ 3 - 3
The Display ___________________________________________________ 3 - 3
InternalAudibleAlarm ___________________________________________ 3 - 4
Modes Of Operation ____________________________________________ 3 - 5
Alarm ________________________________________________________ 3 - 6
How The System Annunciates Fire Alarms ___________________________ 3 - 6
Viewing the List ofAlarms ________________________________________ 3 - 7
How to BlockAcknowledge a FireAlarm _____________________________ 3 - 7
HowtoIndividuallyAcknowledgeaFireAlarm _________________________ 3 - 7
Silencing The System ___________________________________________ 3 - 7
Supervisories __________________________________________________ 3 - 8
How The System Annunciates Supervisories _________________________ 3 - 8
Viewing the List of Supervisories___________________________________ 3 - 8
How to BlockAcknowledge a Supervisory____________________________ 3 - 8
HowtoIndividuallyAcknowledgeaSupervisory _______________________ 3 - 9
Security _______________________________________________________ 3 - 9
How The SystemAnnunciates Security Conditions ____________________ 3 - 9
Viewing the List of Security Conditions ______________________________ 3 - 9
HowtoIndividuallyAcknowledgeaSecurityCondition(UL1076) __________ 3 - 9
Troubles ______________________________________________________ 3 - 10
How The System Annunciates Troubles ____________________________ 3 - 10
Viewing The List of Troubles _____________________________________ 3 - 10
How to BlockAcknowledge a Trouble ______________________________ 3 - 10
HowtoIndividuallyAcknowledgeaTrouble __________________________ 3 - 11

Table of Contents
v
Reset Procedures ______________________________________________ 3 - 11
Hard Reset __________________________________________________ 3 - 11
Soft Reset ___________________________________________________ 3 - 11
UsingThe MKB Keyboard/Annunciator Panel in Global Mode ____________ 3 - 12
Limitations/Restrictions_________________________________________ 3 - 12
Global MKB Display Format _____________________________________ 3 - 12
GlobalKeypadOperation _______________________________________ 3 - 13
UsingThe Menu _______________________________________________ 3 - 14
Operation of the Keys on the MXL-IQAnnunciator Panel _______________ 3 - 14
Numeric Keypad ______________________________________________ 3 - 14
The Command Keypad _________________________________________ 3 - 14
Overview of the Menu’s Structure _________________________________ 3 - 15
Beginning a Menu Session ______________________________________ 3 - 16
IntroductiontotheAcknowledgeMenu _____________________________ 3 - 16
Introduction to the List Menu _____________________________________ 3 - 16
IntroductiontotheControlMenu __________________________________ 3 - 16
Introduction to the Test Menu_____________________________________ 3 - 16
Entering Your Password ________________________________________ 3 - 17
Entering a Module Number and Device Number ______________________ 3 - 17
Entering a Device Number with the Module Number___________________ 3 - 17
Acknowledge Menu ____________________________________________ 3 - 18
EnteringtheAcknowledgeMenu __________________________________ 3 - 18
Acknowledge:Alarm ___________________________________________ 3 - 18
Acknowledge:Supervsry________________________________________ 3 - 19
Acknowledge:Security _________________________________________ 3 - 20
Acknowledge:Trouble __________________________________________ 3 - 21
LIST Menu ____________________________________________________ 3 - 22
Entering the List Menu__________________________________________ 3 - 22
List: Status __________________________________________________ 3 - 23
List:Alarm ___________________________________________________ 3 - 23
List: Supervisory ______________________________________________ 3 - 24

Table of Contents
vi
List Security Conditions_________________________________________ 3 - 24
List:Trouble__________________________________________________ 3 - 25
List: Sensitivity Settings_________________________________________ 3 - 26
List: Voltages _________________________________________________ 3 - 26
List: Temp ___________________________________________________ 3 - 28
List:ModuleType______________________________________________ 3 - 28
List: Device Type______________________________________________ 3 - 29
List: Message ________________________________________________ 3 - 30
List: Software Version __________________________________________ 3 - 30
List: Output States_____________________________________________ 3 - 31
List: Device Usages ___________________________________________ 3 - 32
List: NodeAddress ____________________________________________ 3 - 32
List:Air Sampling______________________________________________ 3 - 32
List: Percent/ft ________________________________________________ 3 - 34
List Percent/ft – Senstvty _______________________________________ 3 - 35
List Percent/ft – Pre-alarm ______________________________________ 3 - 35
List Percent/ft – Analog _________________________________________ 3 - 35
List: ASD_apps _______________________________________________ 3 - 35
CONTROL Menu _______________________________________________ 3 - 36
Enteringthe Control Menu _______________________________________ 3 - 37
Control: Reset ________________________________________________ 3 - 37
Control:Sensitivity_____________________________________________ 3 - 37
Control:Arm/dis_______________________________________________ 3 - 38
Control: Output on/off __________________________________________ 3 - 39
Control: LoopArm _____________________________________________ 3 - 39
Control: Loop Disarm __________________________________________ 3 - 40
Control: Net Link Request _______________________________________ 3 - 40
Control:Air Sampling___________________________________________ 3 - 40
Control: Percent/ft _____________________________________________ 3 - 41
Control: ChangeApps __________________________________________ 3 - 42

Table of Contents
vii
Chapter 4
TEST Menu ___________________________________________________ 3 - 42
Entering the Test Menu _________________________________________ 3 - 43
Test: Set Time ________________________________________________ 3 - 43
Test: Ground Fault_____________________________________________ 3 - 44
Test: Power __________________________________________________ 3 - 44
Test: Lamp Test_______________________________________________ 3 - 45
Test: Device LED _____________________________________________ 3 - 45
Test: MOI Lamp Test ___________________________________________ 3 - 46
Test:Network(X-Network, M-Network) _____________________________ 3 - 46
Test: Override ________________________________________________ 3 - 46
Test: Det_Cleaned_____________________________________________ 3 - 47
Test: Event Log _______________________________________________ 3 - 47
Test: Pyro_diags ______________________________________________ 3 - 48
Test: Pre_alarm_______________________________________________ 3 - 48
Test: ASD_Devices ____________________________________________ 3 - 48
Test: Summarize______________________________________________ 3 - 48
Test:Manual_Activate __________________________________________ 3 - 49
Testing andTroubleshooting __________________ 4 -1
SYSTEM TEST ___________________________________________________ 4 -1
EverySix Months_______________________________________________ 4 -1
Every Year ____________________________________________________ 4 -1
Fuse Replacement _____________________________________________ 4 -1
Troubleshooting________________________________________________ 4 -2

Table of Contents
viii
Chapter 5
Chapter 6
Walktest Operating Instructions _____________ 5 - 1
System w/AUD ________________________________________________ 5 - 2
System SIL ___________________________________________________ 5 - 2
Loopw/AUD __________________________________________________ 5 - 2
LoopSIL _____________________________________________________ 5 - 2
ZonewAUD ___________________________________________________ 5 - 2
ZoneSIL _____________________________________________________ 5 - 2
Cancel_______________________________________________________ 5 - 2
Extend _______________________________________________________ 5 - 2
Suggested Walktest Procedure ____________________________________ 5 - 2
Walktest the System ____________________________________________ 5 - 3
Walktest Ending Sequence _______________________________________ 5 - 4
Walktest EntireALDLoop,MOI-7(MID-16),orCZM-4Module ____________ 5 - 4
Walktest Ending Sequence _______________________________________ 5 - 5
Walktest Individual CZM-1B6 orCZM-4Zone _________________________ 5 - 5
History Log ______________________________ 6 - 1
Logging Methods _______________________________________________ 6 - 2
Small List Logging______________________________________________ 6 - 2
Circular Logging _______________________________________________ 6 - 3
MKB Menu Option to Enable, Disable and Erase History _________________ 6 - 4
Enabling the History Option in CSG-M ______________________________ 6 - 4
From the MKB Menu ____________________________________________ 6 - 4
Local History Log Query __________________________________________ 6 - 5
Query Selection________________________________________________ 6 - 5
Query Filters __________________________________________________ 6 - 5
NavigatingThe History Display _____________________________________ 6 - 6
History Display Formats _________________________________________ 6 - 6
Device Event __________________________________________________ 6 - 6
Reset Event __________________________________________________ 6 - 6