Siemens SIMOTICS S-1FT7 Instruction sheet

Configuration Manual
For SINAMICS S120
SIMOTICS S-1FT7 synchronous motors
09/2018Edition
SIMOTICS
www.siemens.com

___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMOTICS
Drive technology
S-1FT7 synchronous motors
Configuration Manual
09/2018
A5E45099423B AA
Introduction
Fundamental safety
instructions
1
Description of the motors
2
Mechanical properties
3
Motor components and
options
4
Configuration
5
Technical data and
characteristic curves
6
Preparation for use
7
Electrical connection
8
Assembly
drawings/dimension sheets
9
Appendix
A

Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: .
Ⓟ
10/2018 Subject to change
Copyright © Siemens AG 2007 - 2018.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

S-1FT7 synchronous motors
Configuration Manual, 09/2018, A5E45099423B AA 3
Introduction
Additional documents
For configuring, you require Catalog D 21.4
(https://support.industry.siemens.com/cs/document/109747019/) as print version or online.
More information
Information on the following topics is available at:
●Ordering documentation / overview of documentation
●Additional links to download documents
●Using documentation online (find and search in manuals / information)
More information (https://support.industry.siemens.com/cs/de/en/view/108998034)
If you have any questions regarding the technical documentation (e.g. suggestions,
corrections), please send an e-mail to the following address E-mail
(mailto:[e-mail]).
Target group
This documentation addresses project planners and project engineers as well as machine
manufacturers and commissioning engineers.
Benefits
The Configuration Manual enables the target group to apply the rules and guidelines to be
observed when configuring products and systems.
The Configuration Manual supports you with selecting motors, calculating the drive
components, and selecting the required accessories. The Configuration Manual helps the
target group to create a system or plant configuration.
Utilization phase
Planning and configuration phase
My support
The following link provides information on how to create your own individual documentation
based on Siemens content, and adapt it for your own machine documentation:
My support (https://support.industry.siemens.com/My/de/en/documentation)

Introduction
S-1FT7 synchronous motors
4Configuration Manual, 09/2018, A5E45099423B AA
Note
If you want to use this function, you must first register.
Later, you can log on with y
our login data.
Training
The following link provides information on SITRAIN - training from Siemens for products,
systems and automation engineering solutions:
SITRAIN (http://siemens.com/sitrain)
Technical Support
Country-specific telephone numbers for technical support are provided on the Internet under
Contact:
Technical Support (https://support.industry.siemens.com)
Internet address for products
Products (http://www.siemens.com/motioncontrol)
Websites of third parties
This publication contains hyperlinks to websites of third parties. Siemens does not take any
responsibility for the contents of these websites or adopt any of these websites or their
contents as their own, because Siemens does not control the information on these websites
and is also not responsible for the contents and information provided there. Use of these
websites is at the risk of the person doing so.
Information regarding third-party products
Note
Recommendation relating to third-party products
This document contains recommendations relati
ng to third-party products. Siemens accepts
the fundamental suitability of these third
-party products.
You can use equivalent products from other manufacturers.
Siemens does not accept any warranty for the properties of third
-party products.

Introduction
S-1FT7 synchronous motors
Configuration Manual, 09/2018, A5E45099423B AA 5

S-1FT7 synchronous motors
Configuration Manual, 09/2018, A5E45099423B AA 7
Table of contents
Introduction............................................................................................................................................. 3
1 Fundamental safety instructions............................................................................................................ 11
1.1 General safety instructions .....................................................................................................11
1.2 Equipment damage due to electric fields or electrostatic discharge ......................................16
1.3 Industrial security ....................................................................................................................17
1.4 Residual risks of power drive systems....................................................................................19
2 Description of the motors ...................................................................................................................... 21
2.1 Highlights and benefits............................................................................................................21
2.2 Intended use ...........................................................................................................................23
2.3 Technical features and environmental conditions ..................................................................24
2.3.1 Standards and guidelines .......................................................................................................24
2.3.2 Technical features...................................................................................................................26
2.3.3 Torque overview .....................................................................................................................28
2.3.4 Environmental conditions........................................................................................................30
2.4 Derating factors.......................................................................................................................32
2.5 Selection based on the article number ...................................................................................33
2.6 Rating plate data (type plate)..................................................................................................36
3 Mechanical properties ........................................................................................................................... 37
3.1 Cooling....................................................................................................................................37
3.1.1 Natural cooling ........................................................................................................................37
3.1.2 Forced ventilation....................................................................................................................39
3.1.3 Water cooling ..........................................................................................................................40
3.1.3.1 Cooling circuit .........................................................................................................................41
3.1.3.2 Pressure conditions in the cooling circuit................................................................................44
3.1.3.3 Specification of the cooling water ...........................................................................................46
3.1.3.4 Coolant connection .................................................................................................................48
3.2 Degree of protection ...............................................................................................................50
3.3 Types of construction..............................................................................................................52
3.4 Bearing versions .....................................................................................................................52
3.5 Flange forms ...........................................................................................................................53
3.6 Shaft extension .......................................................................................................................54
3.7 Radial and axial forces............................................................................................................54
3.7.1 Sample calculation of the belt pre-tension..............................................................................54
3.7.2 Radial force loading ................................................................................................................55
3.7.3 Radial force diagrams .............................................................................................................56
3.7.4 Axial force loading...................................................................................................................60

Table of contents
S-1FT7 synchronous motors
8Configuration Manual, 09/2018, A5E45099423B AA
3.8 Radial eccentricity, concentricity and axial eccentricity ......................................................... 61
3.9 Balancing ............................................................................................................................... 62
3.10 Vibration response ................................................................................................................. 62
3.11 Noise emission....................................................................................................................... 64
3.12 Bearing change interval ......................................................................................................... 64
3.13 Service and inspection intervals ............................................................................................ 65
4 Motor components and options ............................................................................................................. 67
4.1 Motor components ................................................................................................................. 67
4.1.1 Thermal motor protection....................................................................................................... 67
4.1.2 Encoders ................................................................................................................................ 69
4.1.2.1 Encoders for 1FT7 motors ..................................................................................................... 69
4.1.2.2 Technical specifications of the incremental encoders ........................................................... 71
4.1.2.3 Technical specifications of the absolute encoders ................................................................ 72
4.2 Options................................................................................................................................... 74
4.2.1 Holding brake ......................................................................................................................... 74
4.2.1.1 Type of the holding brake ...................................................................................................... 74
4.2.1.2 Properties............................................................................................................................... 74
4.2.1.3 Technical specifications ......................................................................................................... 76
4.2.2 Output coupling ...................................................................................................................... 77
4.2.3 Motors with planetary gearboxes........................................................................................... 78
4.2.3.1 Properties............................................................................................................................... 78
4.2.3.2 Selection and ordering data for the planetary gearboxes...................................................... 78
4.2.4 Special options....................................................................................................................... 80
4.2.4.1 Introduction ............................................................................................................................ 80
4.2.4.2 Option B02 - Manufacturer’s test certificate........................................................................... 82
4.2.4.3 Option K20 - Reinforced bearing ........................................................................................... 83
4.2.4.4 Option L03 - Increased resistance to vibration ...................................................................... 89
4.2.4.5 Option L06 - increased shock loads ...................................................................................... 91
4.2.4.6 Option N05 - Alternative shaft geometry................................................................................ 92
4.2.4.7 Option N16 - Increased chemical resistance ......................................................................... 94
4.2.4.8 Option N27 - Brake with low moment of inertia ..................................................................... 96
4.2.4.9 Option N40 - Increased resistance to industrial cleaning ...................................................... 97
4.2.4.10 Option Q12 - Sealing air connection.................................................................................... 100
4.2.4.11 Option Q13 - Encoder sealing.............................................................................................. 102
4.2.4.12 Option Q41-Q44 - Connector outlet directions for fixed fan connectors at 1FT7117
force-ventilated..................................................................................................................... 102
4.2.4.13 Options X.., K23, K24, and N16 - Paint finish...................................................................... 103
4.2.4.14 Option Y84 - Customer data on the rating plate .................................................................. 106
5 Configuration .......................................................................................................................................107
5.1 Configuring software ............................................................................................................ 107
5.1.1 SIZER configuration tool ...................................................................................................... 107
5.1.2 STARTER drive/commissioning software............................................................................ 107
5.2 Procedure when engineering ............................................................................................... 108
5.2.1 1. Clarification of the drive type............................................................................................ 109
5.2.2 2. Specification of the supplementary conditions and integration into the automation
system.................................................................................................................................. 109

Table of contents
S-1FT7 synchronous motors
Configuration Manual, 09/2018, A5E45099423B AA 9
5.2.3 3. Definition of the load, calculation of the maximum load torque and determination of
the motor...............................................................................................................................110
5.3 Dimensioning the gearbox ....................................................................................................117
5.4 Brake resistances (armature short-circuit braking)...............................................................120
5.4.1 Description of function braking resistor.................................................................................120
5.4.2 Dimensioning of braking resistors.........................................................................................124
6 Technical data and characteristic curves ............................................................................................. 131
6.1 Explanations .........................................................................................................................131
6.2 Motor overview / assignment of Motor Modules / power cables...........................................142
6.3 Data sheets and characteristics............................................................................................150
6.3.1 1FT7 Compact - natural cooling ...........................................................................................150
6.3.1.1 1FT7034-_A ..........................................................................................................................150
6.3.1.2 1FT7036-_A ..........................................................................................................................152
6.3.1.3 1FT7042-_A ..........................................................................................................................154
6.3.1.4 1FT7044-_A ..........................................................................................................................158
6.3.1.5 1FT7046-_A ..........................................................................................................................162
6.3.1.6 1FT7062-_A ..........................................................................................................................166
6.3.1.7 1FT7064-_A ..........................................................................................................................170
6.3.1.8 1FT7066-_A ..........................................................................................................................174
6.3.1.9 1FT7068-_A ..........................................................................................................................178
6.3.1.10 1FT7082-_A ..........................................................................................................................180
6.3.1.11 1FT7084-_A ..........................................................................................................................186
6.3.1.12 1FT7086-_A ..........................................................................................................................192
6.3.1.13 1FT7102-_A ..........................................................................................................................198
6.3.1.14 1FT7105-_A ..........................................................................................................................204
6.3.1.15 1FT7108-_A ..........................................................................................................................210
6.3.1.16 1FT7132-_A ..........................................................................................................................216
6.3.1.17 1FT7134-_A ..........................................................................................................................222
6.3.1.18 1FT7136-_A ..........................................................................................................................
226
6.3.1.19 1FT7138-_A ..........................................................................................................................230
6.3.2 1FT7 Compact - forced ventilation........................................................................................232
6.3.2.1 1FT7084-_S ..........................................................................................................................232
6.3.2.2 1FT7086-_S ..........................................................................................................................238
6.3.2.3 1FT7105-_S ..........................................................................................................................244
6.3.2.4 1FT7108-_S ..........................................................................................................................248
6.3.2.5 1FT7132-_S ..........................................................................................................................252
6.3.2.6 1FT7134-_S ..........................................................................................................................258
6.3.2.7 1FT7136-_S ..........................................................................................................................262
6.3.2.8 1FT7138-_S ..........................................................................................................................266
6.3.3 1FT7 Compact - water cooling..............................................................................................268
6.3.3.1 1FT7062-_W .........................................................................................................................268
6.3.3.2 1FT7064-_W .........................................................................................................................272
6.3.3.3 1FT7066-_W .........................................................................................................................276
6.3.3.4 1FT7068-_W .........................................................................................................................280
6.3.3.5 1FT7082-_W .........................................................................................................................282
6.3.3.6 1FT7084-_W .........................................................................................................................288
6.3.3.7 1FT7086-_W .........................................................................................................................294
6.3.3.8 1FT7102-_W .........................................................................................................................300
6.3.3.9 1FT7105-_W .........................................................................................................................306

Table of contents
S-1FT7 synchronous motors
10 Configuration Manual, 09/2018, A5E45099423B AA
6.3.3.10 1FT7108-_W ........................................................................................................................ 312
6.3.4 1FT7 High Dynamic - natural cooling................................................................................... 318
6.3.4.1 1FT7087-_A ......................................................................................................................... 318
6.3.4.2 1FT7117-_A ......................................................................................................................... 320
6.3.5 1FT7 High Dynamic - forced ventilation............................................................................... 324
6.3.5.1 1FT7065-_S ......................................................................................................................... 324
6.3.5.2 1FT7067-_S ......................................................................................................................... 328
6.3.5.3 1FT7085-_S ......................................................................................................................... 332
6.3.5.4 1FT7087-_S ......................................................................................................................... 336
6.3.5.5 1FT7117-_S ......................................................................................................................... 340
6.3.6 1FT7 High Dynamic - water cooling..................................................................................... 344
6.3.6.1 1FT7065-_W ........................................................................................................................ 344
6.3.6.2 1FT7067-_W ........................................................................................................................ 348
6.3.6.3 1FT7085-_W ........................................................................................................................ 352
6.3.6.4 1FT7087-_W ........................................................................................................................ 356
7 Preparation for use ..............................................................................................................................361
7.1 Transporting ......................................................................................................................... 361
7.2 Storage................................................................................................................................. 365
8 Electrical connection ............................................................................................................................367
8.1 Permissible line system types.............................................................................................. 367
8.2 Circuit diagram of the motor................................................................................................. 367
8.3 System integration ............................................................................................................... 368
8.3.1 Connection notes ................................................................................................................. 368
8.3.1.1 Rotating a connector on the motor ...................................................................................... 370
8.3.1.2 Routing cables in a damp environment ............................................................................... 374
8.3.1.3 Handling the SPEED-CONNECT connection ...................................................................... 374
8.3.2 Connecting to a converter.................................................................................................... 376
8.3.3 Connecting a separately driven fan ..................................................................................... 384
8.3.4 Connecting the holding brake .............................................................................................. 387
8.3.5 Signal connection / motor protection ................................................................................... 389
8.3.5.1 Motors with DRIVE-CLiQ interface ...................................................................................... 389
8.3.5.2 Motors without DRIVE-CLiQ interface ................................................................................. 392
8.3.5.3 PIN assignment of the signal connectors ............................................................................ 393
8.3.5.4 Signal cables........................................................................................................................ 394
8.3.5.5 Connecting the signal cable on a force-ventilated motor..................................................... 394
9 Assembly drawings/dimension sheets..................................................................................................397
A Appendix .............................................................................................................................................399
A.1 Glossary ............................................................................................................................... 399
Index ...................................................................................................................................................403

S-1FT7 synchronous motors
Configuration Manual, 09/2018, A5E45099423B AA 11
Fundamental safety instructions
1
1.1
General safety instructions
WARNING
Electric shock and danger to life due to other energy sources
Touching live components can result in death or severe injury.
•Only work on electrical devices when you are qualified for this job.
•Always observe the country-specific safety rules.
Generally, the following six steps apply when establishing safety:
1. Prepare for disconnection. Notify all those who will be affected by the procedure.
2. Isolate the drive system from the power supply and take measures to prevent it being
switched back on again.
3. Wait until the discharge time specified on the warning labels has elapsed.
4. Check that there is no voltage between any of the power connections, and between any
of the power connections and the protective conductor connection.
5. Check whether the existing auxiliary supply circuits are de-energized.
6. Ensure that the motors cannot move.
7. Identify all other dangerous energy sources, e.g. compressed air, hydraulic systems, or
water. Switch the energy sources to a safe state.
8. Check that the correct drive system is completely locked.
After you have completed the work, restore the operational readiness in the inverse
sequence.
WARNING
Electric shock due to connection to an unsuitable power supply
When equipment is connected to an unsuitable power supply, exposed components may
carry a hazardous voltage that might result in serious injury or death.
•Only use power supplies that provide SELV (Safety Extra Low Voltage) or PELV-
(Protective Extra Low Voltage) output voltages for all connections and terminals of the
electronics modules.

Fundamental safety instructions
1.1 General safety instructions
S-1FT7 synchronous motors
12 Configuration Manual, 09/2018, A5E45099423B AA
WARNING
Electric shock due to damaged motors or devices
Improper handling of motors or devices can damage them.
Hazardous voltages can be present at the enclosure or at exposed components on
damaged motors or devices.
•Ensure compliance with the limit values specified in the technical data during transport,
storage and operation.
•Do not use any damaged motors or devices.
WARNING
Electric shock due to unconnected cable shield
Hazardous touch voltages can occur through capacitive cross-coupling due to unconnected
cable shields.
•As a minimum, connect cable shields and the conductors of power cables that are not
used (e.g. brake cores) at one end at the grounded housing potential.
WARNING
Electric shock if there is no ground connection
For missing or incorrectly implemented protective conductor connection for devices with
protection class I, high voltages can be present at open, exposed parts, which when
touched, can result in death or severe injury.
•Ground the device in compliance with the applicable regulations.
WARNING
Arcing when a plug connection is opened during operation
Opening a plug connection when a system is operation can result in arcing that may cause
serious injury or death.
•Only open plug connections when the equipment is in a voltage-free state, unless it has
been explicitly stated that they can be opened in operation.

Fundamental safety instructions
1.1 General safety instructions
S-1FT7 synchronous motors
Configuration Manual, 09/2018, A5E45099423B AA 13
NOTICE
Property damage due to loose power connections
Insufficient tightening torques or vibration can result in loose power connections. This can
result in damage due to fire, device defects or malfunctions.
•Tighten all power connections to the prescribed torque.
•Check all power connections at regular intervals, particularly after equipment has been
transported.
WARNING
Unexpected movement of machines caused by radio devices or mobile phones
When radio devices or mobile phones with a transmission power > 1 W are used in the
immediate vicinity of components, they may cause the equipment to malfunction.
Malfunctions may impair the functional safety of machines and can therefore put people in
danger or lead to property damage.
•If you come closer than around 2 m to such components, switch off any radios or mobile
phones.
•Use the "SIEMENS Industry Online Support app" only on equipment that has already
been switched off.
WARNING
Unrecognized dangers due to missing or illegible warning labels
Dangers might not be recognized if warning labels are missing or illegible. Unrecognized
dangers may cause accidents resulting in serious injury or death.
•Check that the warning labels are complete based on the documentation.
•Attach any missing warning labels to the components, where necessary in the national
language.
•Replace illegible warning labels.

Fundamental safety instructions
1.1 General safety instructions
S-1FT7 synchronous motors
14 Configuration Manual, 09/2018, A5E45099423B AA
WARNING
Unexpected movement of machines caused by inactive safety functions
Inactive or non-adapted safety functions can trigger unexpected machine movements that
may result in serious injury or death.
•Observe the information in the appropriate product documentation before
commissioning.
•Carry out a safety inspection for functions relevant to safety on the entire system,
including all safety-related components.
•Ensure that the safety functions used in your drives and automation tasks are adjusted
and activated through appropriate parameterizing.
•Perform a function test.
•Only put your plant into live operation once you have guaranteed that the functions
relevant to safety are running correctly.
Note
Important safety notices for Safety Integrated functions
If you want to use Safety Integrated functions, you must observe the safety notices in the
Safety Integrated manuals.
WARNING
Active implant malfunctions due to electromagnetic fields
Electromagnetic fields (EMF) are generated by the operation of electrical power equipment,
such as transformers, converters, or motors. People with pacemakers or implants are at
particular risk in the immediate vicinity of this equipment.
•If you have a heart pacemaker or implant, maintain the minimum distance specified in
chapter "Correct usage" from such motors.
WARNING
Active implant malfunctions due to permanent-magnet fields
Even when switched off, electric motors with permanent magnets represent a potential risk
for persons with heart pacemakers or implants if they are close to converters/motors.
•If you have a heart pacemaker or implant, maintain the minimum distance specified in
chapter "Correct usage".
•When transporting or storing permanent-magnet motors always use the original packing
materials with the warning labels attached.
•Clearly mark the storage locations with the appropriate warning labels.
•IATA regulations must be observed when transported by air.

Fundamental safety instructions
1.1 General safety instructions
S-1FT7 synchronous motors
Configuration Manual, 09/2018, A5E45099423B AA 15
WARNING
Injury caused by moving or ejected parts
Contact with moving motor parts or drive output elements and the ejection of loose motor
parts (e.g. feather keys) out of the motor enclosure can result in severe injury or death.
•Remove any loose parts or secure them so that they cannot be flung out.
•Do not touch any moving parts.
•Safeguard all moving parts using the appropriate safety guards.
WARNING
Fire due to inadequate cooling
Inadequate cool
ing can cause the motor to overheat, resulting in death or severe injury as a
result of smoke and fire. This can also result in increased failures and reduced service lives
of motors.
•Comply with the specified cooling requirements for the motor.
WARNING
Fire due to incorrect operation of the motor
When incorrectly operated and in the case of a fault, the motor can overheat resulting in fire
and smoke. This can result in severe injury or death. Further, excessively high
temperatures destroy motor components and result in increased failures as well as shorter
service lives of motors.
•Operate the motor according to the relevant specifications.
•Only operate the motors in conjunction with effective temperature monitoring.
•Immediately switch off the motor if excessively high temperatures occur.
CAUTION
Burn injuries caused by hot surfaces
In operation, the motor can reach high temperatures, which can cause burns if touched.
•Mount the motor so that it is not accessible in operation.
Measures when maintenance is required:
•Allow the motor to cool down before starting any work.
•Use the appropriate personnel protection equipment, e.g. gloves.

Fundamental safety instructions
1.2 Equipment damage due to electric fields or electrostatic discharge
S-1FT7 synchronous motors
16 Configuration Manual, 09/2018, A5E45099423B AA
1.2
Equipment damage due to electric fields or electrostatic discharge
Electrostatic sensitive devices (ESD) are individual components, integrated circuits, modules
or devices that may be damaged by either electric fields or electrostatic discharge.
NOTICE
Equipment damage due to electric fields or electrostatic discharge
Electric fields or electrostatic discharge can cause malfunctions through damaged
individual components, integrated circuits, modules or devices.
•Only pack, store, transport and send electronic components, modules or devices in their
original packaging or in other suitable materials, e.g conductive foam rubber of
aluminum foil.
•Only touch components, modules and devices when you are grounded by one of the
following methods:
–Wearing an ESD wrist strap
–Wearing ESD shoes or ESD grounding straps in ESD areas with conductive flooring
•Only place electronic components, modules or devices on conductive surfaces (table
with ESD surface, conductive ESD foam, ESD packaging, ESD transport container).

Fundamental safety instructions
1.3 Industrial security
S-1FT7 synchronous motors
Configuration Manual, 09/2018, A5E45099423B AA 17
1.3
Industrial security
Note
Industrial security
Siemens provides products
and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement
– and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Su
ch systems, machines and components should only be
connected to an enterprise network or the Internet if and to the extent such a connection is
necessary and only when appropriate security measures (e.g. firewalls and/or network
segmentation) are in place.
For additional information on industrial security measures that may be implemented, please
visit:
Industrial security (
http://www.siemens.com/industrialsecurity)
Siemens’ products and solutions
undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and fa
ilure to apply the latest updates may increase customer’s exposure
to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed at:
Industrial security (
http://www.siemens.com/industrialsecurity)
Further information is provided on the Internet:
Industrial Security Configuration Manual
(https://support.industry.siemens.com/cs/ww/en/view/108862708)

Fundamental safety instructions
1.3 Industrial security
S-1FT7 synchronous motors
18 Configuration Manual, 09/2018, A5E45099423B AA
WARNING
Unsafe operating states resulting from software manipulation
Software manipulations (e.g. viruses, trojans, malware or worms) can cause unsafe
operating states in your system that may lead to death, serious injury, and property
damage.
•Keep the software up to date.
•Incorporate the automation and drive components into a holistic, state-of-the-art
industrial security concept for the installation or machine.
•Make sure that you include all installed products into the holistic industrial security
concept.
•Protect files stored on exchangeable storage media from malicious software by with
suitable protection measures, e.g. virus scanners.
•Protect the drive against unauthorized changes by activating the "know-how protection"
drive function.